Sjoef Race BIS12J3 Handleiding

Sjoef Fiets Race BIS12J3

Lees hieronder de 📖 handleiding in het Nederlandse voor Sjoef Race BIS12J3 (10 pagina's) in de categorie Fiets. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

Instrucons Manual

keep this manual

Handbuch

Bewahren Sie dieses Handbuch

Handleiding

Bewaar deze handleiding

S J O E F

Amsterdam

Made in China

in China hergestellt

Gemaakt in China

Bisshops BV

Herengracht 338

1016 CG Amsterdam

The Netherlands

EN - Manual

This manual provides instrucons for assembling and maintaining your new SJOEF

bicycle. Before assembling the bicycle, it is important to follow these steps. As-

sembly is intended for adults only

• Remove the bicycle from the packaging and remove the packaging materials.

The bicycles are manufactured to comply with European standards EN ISO-

8098:2014 or EN ISO-4210:2014. Please note: the manufacturer is not responsi-

ble for improper use or incorrect assembly of the bicycle.

Assembly

The bicycle can be assembled in a few simple steps. It is important to follow the

order of the instrucons in order to make the assembly as easy as possible.

Installing the handlebar and stem (if required)

1. Aach the cone to the stem by ghtening the bolt (if necessary).

2. Insert the stem (including handbrake lever) into the frame.

3. Posion the handlebar at the desired height and check whether it is perpen-

dicular to the front wheel.

4. Tighten the handlebar clamp and/or bolt.

5. Mount the bell on the le side of the steer next to the grip.

Installing the pedals

PLEASE NOTE: there is an (L) on the le and an (R) on the right side of the pedal.

Incorrectly ghtening the pedal will render the bike unusable and will void the

warranty.

1. It is advisable to grease the ends of the pedals so that they can be replaced

easily in the future.

2. An L or R can be read o from the axle of the pedal. Use this to check which

pedal should be ed on the le and which on the right. Are there no L or R

on the pedals? Then the le pedal contains a marking in the form of a line.

(le or right is viewed from the sing posion on the bicycle).

3. Insert the right pedal into the crank and turn the pedal clockwise by hand

towards the front wheel. It should be easy to turn the pedal; if it is s, the

thread may be damaged.

4. Then turn the le pedal by hand counter-clockwise into the crank, also in the

direcon of the front wheel.

5. Finally, ghten the pedals even further using an open-end spanner.

Fing the side wheels (if available)

1. Loosen the rear axle bolts and remove the fender stay.

2. Fit the support wheel arm on the rear axle against the locking plate which is

already ed on the rear axle). Make sure the rear wheel does not slide in the

frame.

3. Screw the outer axle nut ght when the desired height of the side wheels has

been found. The side wheels should stay about 6 mm above the ground on

both sides.

Handlebar pad

Use these cushions by aaching them to the handlebars and stem with the Velcro

strap.

The hand brake

The hand brake is already mounted on the bike. Check whether the brake blocks

press rmly on the rim when braking. Adjust them if necessary and do this regular-

ly:

1. If the margin in the brake handle is too large, ghten the brake cable nut at

the handle to make it ghter.

2. Double check to see if the brake pads are pressing rmly against the rim

when you squeeze the handbrake. If the pads do not t properly on the rim or

if they are crooked, you can unscrew the inner cable nut.

3. Next, straighten the brake pads with one hand. With the other hand, pull on

the inner cable and ghten the inner cable nut again.

4. You can adjust the distance between the brake blocks and rim by turning the

adjusng screw clockwise if further adjustment of the brakes is needed. Make

sure that the brake cable is rmly connected to the brake cable nut when

adjusng.

5. Lastly, ghten the lock nut securely.

Sll having trouble? Ask an expert to help you. Brakes are an essenal part of the

bicycle.

Checking the back pedal brake

It is a useful exercise to check whether the rear wheel turns smoothly before using

the bike. If the wheel turns s, this is usually due to the back-pedal brake being

ghtened too much. The back-pedal brake is located at the rear wheel axle on the

le-hand side and can be corrected in the following way:

1. Unscrew the bolt from the joint.

2. Rotate the joint back in anclockwise direcon (one rotaon should be su-

cient).

3. Tighten the bolt of the joint.

Assemble basket and doll seat (if equipped)

1. Aach the basket to the front, using the 2 supplied bolts and nuts.

2. Aach the doll’s seat to the back, by sliding it onto the doll’s seat mounng

arm. Secure the seat using the 2 screws supplied.

Product specificaties

Merk:	Sjoef
Categorie:	Fiets
Model:	Race BIS12J3

Heb je hulp nodig?

Als je hulp nodig hebt met Sjoef Race BIS12J3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Fiets Sjoef

Sjoef Classic BIS20M1 Handleiding

20 Juni 2023

Sjoef Balance Bike BIS256 Handleiding

19 Juni 2023

Sjoef Race BIS12J3 Handleiding

17 Juni 2023

Sjoef Dolly BIS12M2 Handleiding

16 Juni 2023

Handleiding Fiets

Nieuwste handleidingen voor Fiets

Kawasaki Z800 (2012) Handleiding

15 November 2024

Scott Addict eRIDE 10 Handleiding

15 November 2024

Trek Fuel EXe 9.8 XT Handleiding

14 November 2024

Kindercraft RAPID 2 Handleiding

23 Oktober 2024

Kindercraft FLY PLUS Handleiding

23 Oktober 2024

Kindercraft SPACE Handleiding

23 Oktober 2024

Lionelo Berry Handleiding

20 Oktober 2024

Kindercraft RAPID Handleiding

16 Oktober 2024

Kindercraft 2WAY NEXT Handleiding

16 Oktober 2024

Kindercraft GOSWIFT Handleiding

16 Oktober 2024