Shimano RD-F800-GS Handleiding

Shimano Fietsaccessoire RD-F800-GS

Lees hieronder de 📖 handleiding in het Nederlandse voor Shimano RD-F800-GS (1 pagina's) in de categorie Fietsaccessoire. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

3. Outer casing length

(1) Loosen the B-tension adjustment screw until it is in the

position shown in the illustration.

(2) Check that there is enough slack in the outer casing. Next,

align the outer casing with the bottom

edge of the outer casing holder at the

rear derailleur and then cut of any excess

length of outer casing.

Connect the cable to the rear

derailleur and, after taking up

the initial slack in the cable,

re-secure to the rear

derailleur as shown in the

illustration.

Capreo

SL-F800

OT-SP41 (SIS-SP41)

RD-F800

SS / GS

FH-F700

CS-HG70-S

CN-HG73

SM-SP17 / SM-BT17

Series

RAPIDFIRE (Shifting lever)

Outer casing

Rear derailleur

Type

Freehub

Gears

Cassette sprocket

Chain

Bottom bracket guide

In order to realize the best performance, we recommend that the following

combination be used.

Specifications

Model number

Type

Gears

Total capacity

Applicable sprocket

Smallest sprocket

RD-F800

17 T

9 - 26 T

9 T

Rear Derailleur

Installation of the rear derailleur

5 mm Allen key

Dropout

Bracket

Bracket spindle

Tightening torque :

8 - 10 N·m {70 - 86 in. lbs.}

General Safety Information

WARNING

“Maintenance interval depends on the usage and riding circumstances.

Clean regularly the chain with an appropriate chaincleaner. Never use

alkali based or acid based solvents such as rust cleaners. If those solvent

be used chain might break and cause serious injury.”

• Use the reinforced connecting pin only for connecting the narrow type of chain.

• There are two different types of reinforced connecting pins available. Be sure to check the table

below before selecting which pin to use. If connecting pins other than reinforced connecting pins

are used, or if a reinforced connecting pin or tool which is not suitable for the type of chain is

used, sufficient connection force may not be obtained, which could cause the chain to break or

fall off.

• If it is necessary to adjust the length of the chain due to a change

in the number of sprocket teeth, make the cut at some other place

than the place where the chain has been joined using a

reinforced connecting pin or an end pin. The chain will be

damaged if it is cut at a place where it has been joined with a

reinforced connecting pin or an end pin.

• Check that the tension of the chain is correct and that the chain is not damaged. If the tension is

too weak or the chain is damaged, the chain should be replaced. If this is not done, the chain

may break and cause serious injury.

• Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or

damaged parts may cause the bicycle to fall over and serious injury may occur as a result. We

strongly recommend only using genuine Shimano replacement parts.

• Obtain and read the service instructions carefully prior to installing the parts. If adjustments

are not carried out correctly, the chain may come off and this may cause you to fall off the bicycle

which could result in serious injury.

• Read these Technical Service Instructions carefully, and keep them in a safe place for later

reference.

Note

• If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.

• If the amount of looseness in the links is so great that adjustment is not possible, you should

replace the derailleur.

• You should periodically clean the derailleur and lubricate all moving parts (mechanism and

pulleys).

• If gear shifting adjustment cannot be carried out, check the degree of parallelism at the rear end

of the bicycle. Also check if the cable is lubricated and if the outer casing is too long or too short.

• If you hear abnormal noise as a result of looseness in a pulley, you should replace the pulley.

• You should periodically wash the sprockets in a neutral detergent and then lubricate them again.

In addition, cleaning the chain with neutral detergent and lubricating it can be a effective way of

extending the useful life of the sprockets and the chain.

• If the chain keeps coming off the sprockets during use, replace the sprockets and the chain.

• Use a frame with internal cable routing is strongly discouraged as it has tendencies to impair the

SIS shifting function due to its high cable resistance.

• Always be sure to use the sprocket set bearing the same group marks. Never

use in combination with a sprocket bearing a different group mark.

• Use an outer casing which still has some length to spare even when the

handlebars are turned all the way to both sides. Furthermore, check that the

shifting lever does not touch the bicycle frame when the handlebars are

turned all the way.

• A special grease is used for the gear shifting cable. Do not use DURA-ACE

grease or other types of grease, otherwise they may cause deterioration in

gear shifting performance.

• Grease the inner cable and the inside of the outer casing before use to

ensure that they slide properly.

• For smooth operation, use the specified outer casing and the bottom bracket cable guide.

• Operation of the levers related to gear shifting should be made only when the front chainwheel is

turning.

• The tension pulley has an arrow on it to indicate the direction of rotation. Install the tension pulley

so that the arrow is pointing clockwise when looking at the outer side of the derailleur.

• Parts are not guaranteed against natural wear or deterioration resulting from normal use.

• For maximum performance we highly recommend Shimano lubricants and maintenance products

• For any questions regarding methods of installation, adjustment, maintenance or operation,

please contact a professional bicycle dealer.

Chain toolChain

9-speed super narrow

chain such as

CN-7701 / CN-HG93

8- / 7- /6-speed narrow

chain such as

CN-HG50 / CN-HG40

Reinforced

connecting pin

TL-CN32 / TL-CN27

6.5mm

7.1mm

Silver

Black

Reinforced Connecting Pin

End Pin Link Pin

Group marks

1. Top adjustment

Turn the top adjustment screw to adjust so that

the guide pulley is in line with the outer line of

the smallest sprocket when looking from the rear.

2. Low adjustment

Turn the low adjustment screw so that the guide

pulley moves to a position directly in line with the

largest sprocket.

SIS Adjustment

Top adjustment

screw

Pull

Less than 30 mm

Tightening torque :

6 - 7 N·m {52 - 60 in. lbs.}

Groove

Note: Be sure that the cable is

securely in the groove.

Low adjustment

screw

4. How to use the B-tension adjustment screw

Mount the chain on the chainring and the largest sprocket, and

turn the crank arm to shift gears. Then turn the B-tension

adjustment screw to adjust

so that the guide pulley

does not interfere with the

sprocket but not so close

that it touches the chain.

Next, set the chain to the

smallest sprocket and

repeat the above to make

sure that the pulley does

not touch the sprocket.

Largest sprocket Smallest sprocket

B-tension

adjustment screw

5. SIS Adjustment

Operate the shifting lever several times to move the chain to the

2nd sprocket. Then, while pressing the lever just enough to take

up the play in the lever, turn the crank arm.

When shifting to

3rd

Tighten the outer casing

adjustment barrel until the

chain returns to the 2nd

sprocket. (clockwise)

Loosen the outer casing

adjustment barrel until the

chain touches the 3rd sprocket

and makes noise. (counter

clockwise)

When no sound

at all is heard

Best setting

The best setting is when the shifting lever is

operated just enough to take up the play and the

chain touches the 3rd sprocket and makes noise.

* Return the lever to its original position (the position where

the lever is at the 2nd sprocket setting and it has been

released) and then turn the crank arm clockwise. If the

chain is touching the 3rd sprocket and making noise, turn the outer

casing adjustment barrel clockwise slightly to tighten it until the noise

stops and the chain runs smoothly.

Operate lever to change gears, and check that no noise occurs

in any of the gear positions.

For the best SIS performance, periodically lubricate all

power-transmission parts.

Adjustment bolt Adjustment bolt

Note:

Set the inner cable so that it protrudes by a

length of less than about 30 mm, and then

check that the inner cable does not interfere with

the spokes of the wheel. Stop the wheel from

turning while carrying out this step.

Outer casing

Outer casing holder

Guide pulley

Largest sprocket

Outer line of

smallest sprocket

(2)

(1)

SI-5XJ0A-001-00

Note: Periodically check that there is no gap

between the dropout and the bracket as shown

in the illustration. If there is a gap between

these two parts, problems with gear shifting

performance may occur.

Cutting the outer casing

When cutting the outer casing, cut the opposite end to the end

with the marking. After cutting the outer

casing, make the end round so that the

inside of the hole has a uniform diameter.

Attach the same outer

end cap to the cut end

of the outer casing.

Outer end cap

* If the rear derailleur moves to a large degree, such as in

bicycles with rear suspension, it is recommended that you

replace the cap with an aluminum

cap (sold separately). The end of

the outer casing which has the

aluminum cap should be at the

derailleur side. Aluminum cap

Derailleur side

The sealed cap with

tongue and the rubber

shield should be

installed to the outer

casing stopper of the

frame. Rubber shield

Rubber shield

Be careful not to bend

Sealed cap with tongue

■Replacing the rear derailleur

Guide pulley / Tension pulley

Tightening torque :

2.5 - 5.0 N·m {22 - 44 in. lbs.}

3 mm Allen key

* Service Instructions in further languages are available at :

http://techdocs.shimano.com

Please note: specifications are subject to change for improvement without notice. (English)

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222

3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan

This service instruction explains how to use and maintain the

Shimano bicycle parts which have been used on your new bicycle.

For any questions regarding your bicycle or other matters which

are not related to Shimano parts, please contact the place of

purchase or the bicycle manufacturer.

Be sure to read the service instructions for the Capreo Drive System in conjunction

with these service instructions.

Technical Service Instructions SI-5XJ0A-001

RD-F800 Rear derailleur

Product specificaties

Merk:	Shimano
Categorie:	Fietsaccessoire
Model:	RD-F800-GS

Heb je hulp nodig?

Als je hulp nodig hebt met Shimano RD-F800-GS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Fietsaccessoire Shimano

Shimano SH-TR500 Handleiding

15 November 2024

Shimano ST-R9100-L Handleiding

15 November 2024

Shimano ST-M4000-L Handleiding

12 Juni 2023

Shimano FD-M8000-H Handleiding

9 Juni 2023

Shimano RD-4700-SS Handleiding

8 Juni 2023

Shimano SL-3S35E Handleiding

6 Juni 2023

Shimano FD-R3030-B Handleiding

4 Juni 2023

Shimano FD-M8025-H Handleiding

23 Mei 2023

Shimano ST-9071 Handleiding

22 Mei 2023

Shimano FD-M4000-TS6 Handleiding

21 Mei 2023

Handleiding Fietsaccessoire

Nieuwste handleidingen voor Fietsaccessoire

Knog Oi Luxe Handleiding

26 September 2024

Abus WBA65 Handleiding

18 Augustus 2024

Topeak PRESSURE-RITE SHOCK ADAPTER Handleiding

30 Juli 2024

Blackburn Honest Digital Shock Handleiding

11 Juni 2024

Blackburn Grid Seat Bags Handleiding

11 Juni 2024

Blackburn Outpost Elite Handleiding

11 Juni 2024

Funn Ripper Handleiding

4 Mei 2024

Funn Mamba Handleiding

3 Mei 2024

Basil Bremen Handleiding

5 Maart 2024

Basil SoHo Handleiding

5 Maart 2024