Sharkoon Vibe-Fixer III 5.25" Handleiding
Sharkoon
Geheugenkaartlezer
Vibe-Fixer III 5.25"
Lees hieronder de 📖 handleiding in het Nederlandse voor Sharkoon Vibe-Fixer III 5.25" (2 pagina's) in de categorie Geheugenkaartlezer. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Manual
www.sharkoon.com
HDD VIBE FIXER
1. Apply the cushion pads to the frame (fig. 1).
2. Slide the silicone covers over the 6 clamps of the
frame (fig. 2).
3. Fasten the rubber bands to the outer clamps of
the frame (fig. 3).
9. Fasten the last rubber band to the frame’s central
hook (fig. 7).
This is how the frame should finally look like (fig. 8).
10. Install the frame with the HDD into the computer
case. Secure it with the included screws.
Operating conditions:
Any hard disk of 3.5" width and 1" height can be
mounted and operated with the Vibe-Fixer. The
operation temperature should not exceed 50°
Celsius permanently. For short periods of time, up
to 70° Celsius are tolerable for the rubber bands.
Keep in mind that the aging process of the rubber is
accelerated by heat! The rubber bands must not be
exposed to daylight (UV light) for long periods of
time.
Transportation note:
Rough handling during transportation may cause
some displacement of the hard disk from its rubber
suspension. After transportation open the PC, check
and correct any possible displacement of the disk to
ensure perfect operation of the unit.
It is strongly recommended to check the rubber
bands prior to any movement/shipment of the
computer (see section "Maintenance").
Maintenance:
The rubber bands of the VIBE FIXER are subject to
an aging process. Therefore it is required that the
rubber bands’ condition is checked every 12-18
months and to replace them if needed. Take a very
close look at the spots where the rubber is bent the
most, at the hooks and at the edges of the hard disk.
If cracking shows up, any part of the rubber feels
tacky or if the surface of the rubber bands looks
distinctively whitish, do not use the unit until the
rubbers have been replaced. You can order /
purchase substitution rubber bands at
support@sharkoon.com.
4. Two silicone covers come with a lengthwise cut.
Slide these covers over both inner parts of the
rubber bands (fig. 4).
5. Fasten the two inner parts of the rubber bands
with the included cable tie. Take care to move the
cable tie over the silicone covers (fig. 4). Cut the
overlaying end of the cable tie with a pair of
scissors.
6. Place the frame on a flat surface in front of you.
7. Pull up the outer string of a rubber band and
carefully slide the HDD into the gap (the strings of
the rubber bands which are tied together by the
cable tie go underneath the HDD) (fig. 5).
Note:
Take care that the rubber bands will not be amaged
by the HDD or parts of it.
8. Slide the outer string of the second rubber band
over the HDD and center the drive between the
rubber bands (fig. 6).
Note:
The rubber bands of the frame are quite sensitive to
mechanical damage. Sharp edges of the hard disk
may cause small cuts in the rubber, which might go
unnoticed but could eventually lead to disruption of
the rubber. While inserting the hard disk into the
frame this risk is most present. Therefore any sharp
edges on the hard disk must be covered using
standard isolating tape.
Important:
Never pull or press the rubber bands directly onto
any electronics of the hard disk. It is harmless if the
rubber bands touch the electronics, yet force must
be avoided. Try to avoid placing rubber bands
directly across processor chips of the hard disk as
they might get hot.
1
2
3
4
5
6
7
8
Product specificaties
Merk: | Sharkoon |
Categorie: | Geheugenkaartlezer |
Model: | Vibe-Fixer III 5.25" |
Kleur van het product: | Zwart |
Ondersteunde opslagstationinterfaces: | IDE/ATA |
Aantal storage drives ondersteund: | 1 |
Heb je hulp nodig?
Als je hulp nodig hebt met Sharkoon Vibe-Fixer III 5.25" stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Geheugenkaartlezer Sharkoon
29 Juni 2023
25 Juni 2023
22 Juni 2023
Handleiding Geheugenkaartlezer
- Geheugenkaartlezer HP
- Geheugenkaartlezer Sony
- Geheugenkaartlezer Akasa
- Geheugenkaartlezer Blackberry
- Geheugenkaartlezer Buffalo
- Geheugenkaartlezer D-Link
- Geheugenkaartlezer DeLock
- Geheugenkaartlezer Digitus
- Geheugenkaartlezer Ednet
- Geheugenkaartlezer Eminent
- Geheugenkaartlezer Ewent
- Geheugenkaartlezer Gembird
- Geheugenkaartlezer Goobay
- Geheugenkaartlezer Hama
- Geheugenkaartlezer Hikvision
- Geheugenkaartlezer ICIDU
- Geheugenkaartlezer Icy Box
- Geheugenkaartlezer ID-Tech
- Geheugenkaartlezer Konig
- Geheugenkaartlezer Logilink
- Geheugenkaartlezer Manhattan
- Geheugenkaartlezer Maxell
- Geheugenkaartlezer Media-tech
- Geheugenkaartlezer Nedis
- Geheugenkaartlezer Renkforce
- Geheugenkaartlezer SanDisk
- Geheugenkaartlezer Sigma
- Geheugenkaartlezer Silvercrest
- Geheugenkaartlezer Sitecom
- Geheugenkaartlezer Sweex
- Geheugenkaartlezer Trendnet
- Geheugenkaartlezer Trust
- Geheugenkaartlezer Vivanco
- Geheugenkaartlezer Connect IT
- Geheugenkaartlezer CSL
- Geheugenkaartlezer Sandberg
- Geheugenkaartlezer Vantec
- Geheugenkaartlezer ABN AMRO
- Geheugenkaartlezer Rabobank
- Geheugenkaartlezer Conrad
- Geheugenkaartlezer Conceptronic
- Geheugenkaartlezer Hamlet
- Geheugenkaartlezer NZXT
- Geheugenkaartlezer SilverStone
- Geheugenkaartlezer Cherry
- Geheugenkaartlezer Satechi
- Geheugenkaartlezer SIIG
- Geheugenkaartlezer Sven
- Geheugenkaartlezer Approx
- Geheugenkaartlezer Enermax
- Geheugenkaartlezer I-Tec
- Geheugenkaartlezer Lexar
- Geheugenkaartlezer Lloyds Bank
- Geheugenkaartlezer UBS
- Geheugenkaartlezer IOGEAR
- Geheugenkaartlezer Speed-Link
- Geheugenkaartlezer IC Intracom
- Geheugenkaartlezer Arctic Cooling
- Geheugenkaartlezer Equip
- Geheugenkaartlezer Icy Dock
- Geheugenkaartlezer Revoltec
- Geheugenkaartlezer StarTech.com
- Geheugenkaartlezer Sonnet
- Geheugenkaartlezer Sabrent
- Geheugenkaartlezer Raidsonic
- Geheugenkaartlezer Rocstor
- Geheugenkaartlezer Urban Factory
- Geheugenkaartlezer OneSpan
- Geheugenkaartlezer EXSYS
- Geheugenkaartlezer Green House
Nieuwste handleidingen voor Geheugenkaartlezer
19 November 2024
30 September 2024
24 September 2024
27 Augustus 2024
17 Augustus 2024
26 Juli 2024
25 Juli 2024
25 Juli 2024
25 Juli 2024