Shark Steam & Scrub S7001 Handleiding

Shark Niet gecategoriseerd Steam & Scrub S7001

Lees hieronder de 📖 handleiding in het Nederlandse voor Shark Steam & Scrub S7001 (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/9
S7001 Series
OWNERS GUIDE
Scrubbing & Sanitizing* Steam Mop
STEAM & SCRUB
s h a r k c l e a n . c o m
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ CAREFULLY BEFORE USE • HOUSEHOLD USE ONLY
This steam mop has a polarized plug (one blade is wider than the other). As a
safety feature, this plug will fit into a polarized outlet only one way. If the plug
does not fit fully into the outlet, reverse the plug. If it still does not fit, contact
a qualied electrician. DO NOT attempt to defeat this safety feature. It is not
recommended to use an extension cord with this product.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
GENERAL WARNINGS
WHEN USING YOUR SHARK®
STEAM & SCRUB, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS
BE FOLLOWED, INCLUDING THE
FOLLOWING:
1. DO NOT leave the steam mop
unattended when plugged in.
ALWAYS unplug the power cord
from the electrical outlet when not
in use and beforeservicing.
2. DO NOT use with damaged
cord or plug. If steam mop is not
working as it should or has been
dropped, damaged, left outdoors,
or dropped into water, return it
to SharkNinja Operating LLC for
examination and repair. Incorrect
reassembly or repair can cause a
risk of electrical shock or injury
when the steam mop is used.
3. To protect against a risk of electric
shock, DO NOT immerse the steam
mop in water or any other liquids.
4. DO NOT handle the plug or steam
mop with wet hands or operate it
without wearing shoes.
5. DO NOT pull or carry by cord, use
cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. run DO NOT
steam mop over cord. Keep cord
away from heated surfaces.
6. DO NOT unplug by pulling on
power cord. To unplug, grasp the
plug not the power cord. DO NOT
use extension cords or outlets
with inadequate current-carrying
capacity.
7. Unplug before servicing.
8. ALWAYS make sure the steam mop
is UNPLUGGED when not in use.
9. NEVER fill the steam mop or attach
the mop head when the steam mop
is plugged into an electrical outlet.
Unplug from the electrical outlet
and allow to cool before you fill the
mop, or attach or remove the head.
10. When cleaning the exterior of the
steam mop, unplug the power cord
from the electrical outlet and clean
the steam mop with a dry or damp
cloth. DO NOT pour water or use
alcohol, benzene, or paint thinner
on the steam mop.
11. To avoid circuit overload, DO NOT
operate another appliance on the
same socket (circuit) as the steam
mop.
12. To avoid scalding injuries, ALWAYS
unplug and allow the steam mop to
cool before removing or changing
mop heads, accessories, or
Dirt Grip® pads.
USE WARNINGS
13. When in use, turn the NEVER
steam mop over on its side or
direct steam toward people, pets
or plants.
14. Use the system only for its
intended use.
15. DO NOT use for space-heating
purposes.
16. DO NOT use outdoors.
17. DO NOT allow the steam mop to be
used by children. Close attention is
necessary when used near children,
pets, or plants.
18. Use only as described in this
owner’s guide.
SAVE THESE INSTR
When assembling your steam mop there may be a little water in or around the water tank.
This is because we test all our steam mops before you buy them, so you get a quality
Shark ® Steam & Scrub steam mop.
a Steam Mop Handle
b Quick-Release Cord Holder
c Steam Mop Body
d Mop Head
e Water Tank Lid
f Mode Button
g Dirt Grip® Soft Scrub Pads
h Filling Flask
a
b
h
c
eg
f
d
s h a r k c l e a n . c o m
GETTING STARTED
NOTE: To prolong the life of your steam
mop, we recommend using distilled water.
NOTE: Sweep or vacuum youroors prior
to cleaning with your steam mop.
1 Make sure both pads are properly installed
before using.
2 Twist the quick-release cord holder
to unwrap the power cord completely
(fig. 5). Plug into an electrical outlet.
3 When it's first plugged in, the unit will be
in Standby mode. The 3 settings lights
below the mode button will blink to
indicate Standby mode.
4 To select the steam mode, press the mode
button once for LIGHT, twice for NORMAL,
or 3 times for DEEP . Once the (fig. 6)
mode is selected, tilt the handle down to
activate the spinning pads . (fig. 7)
TIP: If the handle is not reclined, the mode
selection may time out and pads will
not spin.
TIP: When cleaning near baseboards,
edges, or furniture, you may feel a slight
pull from the unit making contact with
these surfaces. This is normal and not a
cause for concern.
5 Mop with a forward and backward motion.
6 When finished mopping, press the mode
button. The blue settings lights will blink,
indicating that the unit is in Standby mode.
Once in Standby mode, lift the handle to
bring the steam mop back to the upright
position and unplug the unit.
7 When the pads have cooled completely,
remove them by pulling them o the discs.
8 When the water tank is empty, the unit
will stop producing steam. Make sure the
unit is unplugged before refilling the water
tank.
Please wait 2 to 3 minutes for the NOTE:
steam mop to cool o before removing the
Dirt Grip® pads. leave the steam NEVER
mop with damp or wet Dirt Grip pads on
any floor for an extended period.
fig. 5 fig. 6 fig. 7
USING YOUR STEAM & SCRUB
s h a r k c l e a n . c o m
AFTER USE AND STORAGE
1 Press the mode button until the settings
lights below start to blink, indicating that
you are in Standby mode. Unplug the cord
from the outlet and place the steam mop
into the upright position. Let it cool .(fig. 8)
2 When the pads have cooled completely,
remove them by pulling them o the discs.
(fig. 9)
.
3 After the unit has cooled and the steam has
been released, empty the water tank before
storing.
Open the tank lid and pour the water out
into a sink or bathtub. After all the water
has drained out, close the lid.
4 To store the steam mop, wait until after
it has cooled and the steam has been
released. Store steam mop in a dry
protected area until next use.
DIRT GRIP® SOFT SCRUB PADS
CARE INSTRUCTIONS
Care
Machine-wash the Dirt Grip Soft Scrub Pads
separately with warm water using liquid
detergent.
NEVER USE BLEACH, POWDERED
DETERGENT, OR FABRIC SOFTENERS as
they may damage the Dirt Grip Soft Scrub
Pads or leave a coating that will reduce their
cleaning performance and absorbency
. Dirt
Grip Soft Scrub Pads
should be line-dried
or tumble-dried on a low setting, as this will
extend the life of the microfiber fabric
(fig. 10).
Loose fibers can indicate wearing of the
microfiber fabric. pull the loose DO NOT
fibers, as this can cause the weave to come
undone. Simply trim the loose fibers with
scissors (fig. 11).
Replacement Dirt Grip Soft Scrub Pads
For best cleaning results, we recommend
replacing the Dirt Grip Soft Scrub Pads every
3 to 4 months following normal use. As with
any fabric, dirt particles, grease, friction, and
repeated washing can cause the fibers to break
down, and you may notice an increase in the
eort needed to push or pull the mop.
You can purchase replacement Dirt Grip Soft
Scrub Pads and other accessories by visiting
sharkclean.com.
fig. 8
fig. 10
fig. 11
fig. 9
s h a r k c l e a n . c o m
CARING FOR YOUR STEAM & SCRUB
PROBLEM POSSIBLE REASONS & SOLUTIONS
The steam mop
isn’t producing any
steam.
The steam mop should be securely plugged into an electrical outlet. Check
your fuse or circuit breaker or try a dierent outlet.
Make sure the water tank is full, the unit is plugged in, and the mode button is
illuminated.
If the settings lights are o, try a dierent electrical outlet.
If the
settings lights
are blinking, press the mode button to select a steam
setting.
If the settings lights are illuminated steadily, wait 30 seconds for the unit to warm up.
If after following the above steps the steam mop still does not produce any steam,
contact Customer Service at 1-800-798-7398 or visit sharkclean.com
The steam mop
is producing
intermittent steam.
This is normal. For more consistent steam, select the NORMAL setting.
Also make sure the water tank is full.
I can’t select a
steam setting.
Make sure the steam mop is plugged in and the settings lights are flashing.
If your steam mop is producing steam but the settings lights are o, call
Customer Service at 1-800-798-7398.
Floors are cloudy,
streaky, or spotty
after steaming.
The Dirt Grip® Soft Scrub Pads might be dirty. Install a clean set of pads. If you
washed the Dirt Grip Soft Scrub Pads with powdered detergent, then they
could be damaged and require replacement.
Due to accumulated soap or grease residue, the floor may require several
cleanings with the Steam Mop.
A more stubborn case may require you to rinse the floor with a mix of one
part vinegar and two parts water* (but put any cleaning solution into DO NOT
the steam mop's water tank.)
*Please consult your flooring manufacturer’s care and maintenance
instructions before applying any cleaning products or solutions.
It’s hard to push or
pull the mop.
The mop might be hard to push or pull if the Dirt Grip Soft Scrub Pads aren’t
wet enough. It should get easier to move the mop across the floor after it’s
been running for a few minutes.
Overly dirty pads could also make it harder to push or pull the mop. We
recommend using clean pads.
Rotating discs are
not turning or are
wobbling.
The steam mop may be in the upright position. Tilt the handle down to use the
mop.
The Dirt Grip Soft Scrub Pads may not be centered. Turn the power OFF,
unplug the steam mop, wait for a few moments to allow the pads to cool, then
reinstall the Dirt Grip Soft Scrub Pads.
The steam mop
is vibrating or
wobbling.
The Dirt Grip Soft Scrub Pads are not centered on the rotating discs. Turn
the power OFF and unplug the unit, and wait for the pads to cool. Follow the
instructions in the Assembling Your Steam & Scrub section to reinstall
the pads.
The steam mop
turns o on its own.
If your steam mop shuts o in use, it likely needs to cool down. Perform the
following steps before you restart cleaning:
1. Turn the steam mop o, unplug it, and remove pads.
2. Allow the unit to cool for a minimum of 30 minutes.
3. Reinstall the pads. Plug in the steam mop, select a steam mode, and
begin cleaning.
s h a r k c l e a n . c o m
TROUBLESHOOTING
s h a r k c l e a n . c o m
NOTES
s h a r k c l e a n . c o m
ONE (1) YEAR LIMITED WARRANTY
The One (1) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja
Operating LLC. Warranty coverage applies to the original owner and to the original product only and is
not transferable.
SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period
of one (1) year from the date of purchase when it is used under normal household conditions and
maintained according to the requirements outlined in the Owners Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion, will be
repaired or replaced up to one (1) year from the original purchase date.
2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the
receipt date of the replacement unit or the remainder of the existing warranty, whichever is later.
SharkNinja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
1. Normal wear and tear of wearable parts (such as Shark Cleaner, Pad, etc.), which require regular
maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this
warranty. Replacement parts are available for purchase at .sharkaccessories.com
2. Any unit that has been tampered with or used for commercial purposes.
3. Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure
to perform required maintenance, or damage due to mishandling in transit.
4. Consequential and incidental damages.
5. Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused
in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the
repair is performed by a repair person not authorized by SharkNinja.
6. Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal household conditions within the warranty
period, visit sharkclean.com/support for product care and maintenance self-help. Our Customer Service
Specialists are also available at to assist with product support and warranty service options, 1-800-798-7398
including the possibility of upgrading to our VIP warranty service options for select product categories. So
we may better assist you, please register your product online at registeryourshark.com and have the product
on hand when you call.
SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of
$24.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call to initiate a warranty claim. You will need the receipt as proof of purchase. 1-800-798-7398
We also ask that you register your product online at registeryourshark.com and have the product on hand
when you call, so we may better assist you. A Customer Service Specialist will provide you with return and
packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to
state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the
above may not apply to you.
© 2021 SharkNinja Operating LLC.
DIRT GRIP, INTELLIGENT STEAM CONTROL, and SHARK are registered trademarks of SharkNinja Operating LLC.
S7001 Series�IB�Sanitize�MP�Mv14
PRINTED IN CHINA
SharkNinja Operating LLC
US: Needham, MA 02494
CAN: Ville St-Laurent, QC H4S 1A7
1-800-798-7398
sharkclean.com
Illustrations may dier from actual product. We are constantly striving to improve our products,
therefore the specifications contained herein are subject to change without notice.
For SharkNinja U.S. patent information, visit sharkninja.com/uspatents/
*Sanitization studies were conducted under controlled test conditions. Household conditions and
results may vary. With mop head in DEEP mode.
PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.


Product specificaties

Merk: Shark
Categorie: Niet gecategoriseerd
Model: Steam & Scrub S7001

Heb je hulp nodig?

Als je hulp nodig hebt met Shark Steam & Scrub S7001 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Shark

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd