Sanyo LNS-T02E Handleiding

Sanyo Projector accessoire LNS-T02E

Lees hieronder de 📖 handleiding in het Nederlandse voor Sanyo LNS-T02E (4 pagina's) in de categorie Projector accessoire. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

PARTS LIST

Following parts are contained in the packing.

· LENS

· LENS MOUNTING SCREWS

· DRIVER

· LIGHT-BLOCK SHEET

· LENS COVER (UPPER · LOWER )

NOTES ON LENS INSTALLATION

LCD PROJECTOR LENS

MODEL NO. LNS-W02/T02

LNS-W02K/T02K Series

Lens installation should be performed by the qualiﬁed service personnel.

It should be followed by this procedure precisely.

Before attempt to install the lens, conﬁrm the model number (both the LCD

projector and the lens) and use the proper lens.

If you have any questions, contact to the dealers.

Following checks and conﬁrmations should be taken for safety.

Check the following things by the time of the cabinet assembly after the

lens installation.

1. Conﬁrm the lens is securely ﬁxed by 4 screws.

2. Wiring must not be tangled in the gear of the lens motor or the other

mechanical part.

3. There is no missing part, or no loosing mounting part.

1AA6P1P2289-- (ICSC)

1 piece

6 screws (2 for spare)

1 piece

1 sheet

1 set

LENS REPLACEMENT AND

INSTALLATION PROCEDURE

LENS REPLACEMENT AND INSTALLATION PROCEDURE

Remove screws A (2 screws).

Pull down the lower lens cover while pushing

the part D, then remove it.

Remove screws B (2 screws).

Remove screws C (2 screws) and remove

upper lens cover.

1 5Perform the steps for lens replacement and installation.to

Fig-1

Fig-3

●IN CASE OF MODEL WITHOUT LENS

Remove 2 screws and pull down the plate.

UPPER LENS COVER

LOWER LENS COVER

COVER PLATE

REMOVE THE LENS COVER.

(At the step , insert the light-block sheet in the same

position as the removed cover plate has been placed.

Two screws are not used.)

Use the light-block sheet included with lens.

REMOVE THE COVER PLATE OF THE LENS COVER. (See ﬁgure-3)

Set the light-block

sheet, so that the

large rounder side

is set over the lens.

SCREWS

LIGHT-BLOCK SHEET

Fig-2

LENS COVER

Remove 4 screws of the lens cover and

remove the lens cover.

First, set the lens at the center position with

lens shift button.

First check the shape of cabinet.

In case ﬁgure-1 cabinet.

In case ﬁgure-2 cabinet.

LENS MOTOR LEAD

CONNECTOR “ K16B”

(D)

(D)(D)

(D)

LENS MOTOR

❋Figure shown inside of the cabinet.

REMOVE THE LENS. (See ﬁgure-4)

1. Remove the connector “K16B” of the

circuit board.

2. Loosen the A, B, C wire holder and

remove the lens motor lead.

3. Remove screws D (4 screws) which

fastens the lens and remove the lens.

●IN CASE OF MODEL WITH LENS

ATTACHED DRIVER

Fig-5

LENS MOUNTING BRACKET

LENS MOTOR LEAD

CONNECTOR “K16B”

(D)

(D)(D)

(D)

LENS MOTOR

Fig-4

This part wiring should

not be tightened.

INSTALL THE LENS. (See ﬁgure-4,5)

1. Remove protective caps (front

and back ) on the lens.

2. Mount the lens at the lens

mounting bracket with screws

(4 screws) included with the

lens. Use the driver included

with the lens to fasten the

screws . (After using, save it for

latter use.) (See ﬁgure-5)

3. Connect the lens motor lead to

the connector “K16B” of the

circuit board. (See ﬁgure-4)

4. Fasten the lens motor lead at

the A, B, C points with wire

holder.

(See ﬁgure-4)

Product specificaties

Merk:	Sanyo
Categorie:	Projector accessoire
Model:	LNS-T02E
Kleur van het product:	Zwart
Gewicht:	3100 g
Diameter:	130 mm
Diafragma (F-F):	2 - 2.8
Brandpuntbereik:	158 - 221 mm
Zoomverhouding:	1.4x
Compatibiliteit:	PLC-HF10000L\nPLC-HF15000L\nPLC-XF1000\nPLC-XF47\nPLC-XF47A