Sanwa PC20TK Handleiding

Sanwa Niet gecategoriseerd PC20TK

Lees hieronder de 📖 handleiding in het Nederlandse voor Sanwa PC20TK (41 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/41
MULTIMETER
PC20TK
Assembling Training for
Digital Multimeter
Instruction Manual for Assembling and Operation Procedures
1
[1] Warnings for Safe Use of Multim
(Be sure to read this section before u
The instructions given in the text un
Warning and Caution must be observed to prevent
burns, electric shocks and other sim
1-1 Explanation of s
The symbols and their meanings use : Indicates information that is particularly important for safe use.• A warning message is given to prevent burns, electric shock and other accidents resulting in injury or death.• A cautionary message is given relating to any possibility of damaging this product. : Indicates that this part is potentially dangerous because it may be charged with high voltage. :
Double insulation or reinfo
: Fuse : Buzzer + : Positive : Ground : AC : Diode - : Negative
Ω : Resistance
: DC : Capacitor 1-2 Warning messag
The following warning messages are given to prevent accidents resulting in injury or death owing to burns, electric shock or other. Be sure to observe these instructions along with the ones included in this instruction manual.1. Do not use the PC20TK with any power line exceeding 6 kVA.2. Be careful about voltage of 33 VAC rms (46.7 Vpeak) or 70 VDC minimum because it is dangerous to the human body.3. Do not input any signal exceeding the maximum rated input value.4. Do not try to measure a line (e.g., to a motor) where induced voltage or surge voltage may occur, because the maximum overload input value might be exceeded.5. Do not use the PC20TK if its main body or test lead is damaged or broken.6. Do not use the PC20TK with its case removed.7. Do not use any substitute for a fuse or connect wire for non-electrical use.8. During measurement, do not hold any portion of the test pin beyond the test lead.9. Do not input voltage to the current measurement connector. Inputting voltage to that connector will result in a short-circuit, blowing out the built-in fuse. However, this may involve a danger.10. Do not change over to any other mode during measurement.11. Ensure that you have selected the proper range and mode for each measurement run.12. Use the specified type (TL-21) of test lead.13. Do not try to make a measurement with the PC20TK or your hand being wet.14. Use the PC20TK indoors.15. Check the appearance and the display of each mode (range) at least once a year.
Warning
The PC20TK is not provided with an automatic power-off capability. Be sure to turn OFF the Function switch after measurement has been finished, because the batteries will otherwise run out earlier.
Caution
Prior to the assembling of the PC20TK, check the parts in accordance with paragraph (2) in "4-5 Preparations for assembling."
Note
2
[2] Using the PC20TK
2-1 Intended uses and features
1. The PC20TK is a kit for a general-purpose digital multimeter (DMM), which has been designed for
educational uses. Once assembled, it may be used as a normal small-capacity DMM for low-
voltage measurements.
2. The PC20TK features the auto mode that automatically selects an appropriate measurement range
in accordance with the measured value. It may also be used in the manual mode (measurement
range fixed or manually selectable) that allows for faster measurements.
3. The PC20TK allows the user to measure electric capacitance of a capacitor, which is often used
with a resistor as a circuit component.
4. The current measurement connector is provided with a safety cover that prevents the user from
inserting a test lead into it by mistake.
5. If you connect the PC20TK to your PC by using the optionally available PC link (software) and PC
link cable, changes in electric quantity can be displayed as values or graphs on the PC monitor.
2-2 Names of various parts
Range Hold switch
Function switch
with power switch
Hole for VDC adjustment
(DCV ADJ.)
Panel
LCD
Select switch
Data Hold
switch
Safety cover
COM (-) connector
V, Ω, , ,
(+) measurement connector
µA & mA
measurement
connector
Rear case
mounting
screw
Stand
LED
Fig. 1-1: Names of various parts
Fig. 1-2: Test leads (TL-21) Fig. 1-3: Readout
(a) (b) (c)
Decimal point
Value displayed
Measurement
unit
Negative sign for
numeric data
AC measurement
indicator
DC measurement
indicator
Auto mode
RS232C mode
Diode test
mode
Continuity
check mode
Data hold
mode
Relative value
measurement mode
( measurement only)
Battery level
warning
Put the seal after
adjustment.
Test pin
Flange
Pin plug Grip Cord
When
not covered
Removable
test pin
covers

Product specificaties

Merk: Sanwa
Categorie: Niet gecategoriseerd
Model: PC20TK

Heb je hulp nodig?

Als je hulp nodig hebt met Sanwa PC20TK stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Sanwa

Sanwa

Sanwa PC20TK Handleiding

5 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Vitec

Vitec MGW Diamond-HX OG Handleiding

23 November 2024
Electrolux

Electrolux STA9 Handleiding

23 November 2024
Electrolux

Electrolux UMP3 Handleiding

23 November 2024
Electrolux

Electrolux ZS70GL Handleiding

23 November 2024
Bosch

Bosch HEZ8TK36UC Handleiding

23 November 2024
Bosch

Bosch HEZ8ZZ36UC Handleiding

23 November 2024
Bosch

Bosch HDZIT301 Handleiding

23 November 2024
Bosch

Bosch HEZBS301 Handleiding

23 November 2024
LG

LG LX-330 Handleiding

23 November 2024
Stamos

Stamos S-PLASMA 60U Handleiding

23 November 2024