SAB Heli Division Head HPS3 - H0640-K Handleiding
SAB Heli Division
Modelbouw
Head HPS3 - H0640-K
Lees hieronder de 📖 handleiding in het Nederlandse voor SAB Heli Division Head HPS3 - H0640-K (2 pagina's) in de categorie Modelbouw. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Approx 45 mm
11mm
Linkage Rod A Assembly . . . .x3
(Initial length for the rods from the
swashplate to the Blade Grip.)
Please read this user manual carefully, it contains instructions for the correct assembly of the KIT.
Please refer to the website www.goblin-helicopter.com for updates and other important information. Thanks You.
Blade Grip Linkage Assembly
Head Cap
Screw M2.5x15mm
(HC028-S)
Flanged Bearing
2.5x
6x2.5
(HC400-S)
Bushing
[H0599]
Blade Grip Linkage
(H0598-S)
Linkage Rod
(H0561-S)
Plastic Ball Link
(H0403-S)
Center Hub Assembly
Center Hub
(H0595-S)
Spindle
(H0596-S)
Uniball M2
(H0538-S)
Uniball M2
(H0538-S)
Uniball M2
(H0537-S)
Swashplate
Assembly
(H0600-S)
Swashplate Assembly
Blade Grip Assembly
Head Cap
Screw M2.5x8mm
(HC020-S)
Bearing
5x
10x4mm
(HC411-S)
Blade Grip Arm
(H0597-S)
Main Blade Grip
(H0513-S)
Washer
7.5x
10x0.5
(H0349-S)
Thrust Bearing
5x
10x4mm
(HC435-S)
Blade Grip Linkage
Assembly
Head Cap Screws
Shoulder M3x16mm
(HC074-S)
Nylon Nut M3
(HC206-S)
Nylon Nut M3
(HC206-S)
Head Cap Screws
Shoulder M3x18
(HC079-S)
Blade Grip
Assembly
C Washer
5x
7x0.2mm
(HC449-S)
[HC449-S]
[H0513-S][H0595-S]
Note
eg: Microlube GL261
HEX 2.5 Inside
Button Head Cap
Screw M4x6mm
(HC096-S)
Bearing
5x
10x4mm
(HC411-S)
A27_Rev 01
Page 1
HPS3 ROTOR HEAD
[
H0640-K
]
Swashplate
[H0600-S]
- 1 x Swashplate Assembly.
- 5 x UniBall M2
4.7H3.
- 1 x UniBall M2
4.7H20.
Radius Arm
[H0421-S]
- 1 x Center Hub.
- 1 x Socket Head Cap Screw Shouldered M3x16mm.
- 1 x Metric Hex Nylon Nut M3.
Center Hub
[H0595-S]
- 2 x Radius Arms.
- 2 x Spacer Arm
3x
5x2.7mm.
- 1 x Spacer Hex.
- 1 x Uniball Radius Arms.
- 2 x Socket Head Cap Screws M3x16mm.
- 2 x Socket Head Cap Screws M2.5x10mm.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
- 4 x Flanged Bearings
3x
7x3mm.
Linkage
[H0598-S]
- 1 x Linkages.
- 1 x
Linkage Rod
.
- 1 x Bushing.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
Damper Derlin
[H0426-S]
- 3 x H0426-A.
- 3 x H0426-B.
- 3 x H0426-C.
- 3 x Washers
10x
16x1mm.
- 3 x Washers
10x
16x0.2mm.
- 3 x Orings 3050.
Recommendations
- These parts should be used only with models SAB Goblin
- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapther 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and the O-Ring.
- Check for axial play of the spindle at least after the first 10 flights and add shims if necessary.
- Firmly tighten the blades before flight.
About HPS
HPS stands for "High Precision System". This head has been
developed in order to increase the usable rotor RPM range without
having to change the rigidity of the dampening system.
The new head is developed specially to limit the teetering effect of
the spindle by means of dampening achieved by a special
technopolymer material.
The maximum teetering amount can be adjusted based on the
amount of play shown in figure "A" of the drawing. The O-ring is
necessary to create a radial and axial preload.
The preload can be kept relatively low, thanks to the mechanical
locking properties of the technopolymer dampeners.
With this solution, finding the correct preload is less complex.
This solution is safer because there is a physical "stop" of the
teetering effect with the technopolymer dampers, also with low
axial preload.
The change of preload will serve exclusively to customize the
response of the model.
Furthermore, the spindle can only move vertically thanks to the
elongated hole shown in section "B" of the drawing.
This solution allows an optimal control of the geometry even when
large amounts of torque are introduced into the system.
The head is very accurate and reliable.
Spare Parts
- 2 x Blade Grip.
- 2 x Thrust Bearing
5x
10x4mm.
- 4 x Bearing
5x
10x4mm.
- 2 x Washer
7.5x
10x0.5mm.
- 2 x Button Head Socket Cap M4x6mm.
- 2 x Washer
5x
7x0.1mm.
Blade Grip
[H0513-S]
- 1 x Blade Grip Arm.
- 1 x Socket Head Cap Screw M2.5.x8mm.
Blade Grip Arm
[H0597-S]
Spindle Shaft
[H0596-S]
- 1 x Spindle Shaft.
- 1 x C Washer
5x
5x0.2mm.
ABOUT HPS3
For safety reasons we suggest to not exceed 3400 rpm.
In addition, we recommend using a smaller tail pulley in order to increase the tail rotor speed to counteract the additional
torque introduced by the 3rd rotor blade. You will find a 20T tail rotor pulley in the kit for this purpose.
TIPS:
Left Side
Right Side
* To remove the dampeners, you
can use a flathead screwdriver
through the hole as shown.
* Clock-wise, counter clock-wise thread
* By turning the linkages you can adjust
tracking. If tracking is adjusted correctly,
you’ll see the metal part line up around
in the center of the opening.
Detail B
SPARE PARTS
RECOMMENDATIONS
These parts should be used only with models SAB Goblin 380.
- 3 blade rotor heads require a much lower cyclic gain on flybarless systems.We recommend that you set your gain at least 30%
lower than the gain you normally use on your 2 blade rotor head helicopters.You can start increasing the gain after you
complete your first flight. Running too high of a gain can induce a violent oscillation that can potentially cause damage
to your helicopter in flight.
- Please follow all the instructions shown in the Goblin main manual.
In this manual please read Chapter 2, Important notes
- Use Loctite on all threads.
Page 2
HPS3 ROTOR HEAD
[
H0640-K
]
Product specificaties
| Merk: | SAB Heli Division |
| Categorie: | Modelbouw |
| Model: | Head HPS3 - H0640-K |
Heb je hulp nodig?
Als je hulp nodig hebt met SAB Heli Division Head HPS3 - H0640-K stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Modelbouw SAB Heli Division
10 Juli 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023
Handleiding Modelbouw
- Modelbouw Lego
- Modelbouw Blade
- Modelbouw FALLER
- Modelbouw Geomag
- Modelbouw Graupner
- Modelbouw Kibri
- Modelbouw Marklin
- Modelbouw Mega Bloks
- Modelbouw Multiplex
- Modelbouw Playmobil
- Modelbouw Pocher
- Modelbouw Reely
- Modelbouw Revell
- Modelbouw Robbe
- Modelbouw Viessmann
- Modelbouw Voltcraft
- Modelbouw Wiking
- Modelbouw Wilesco
- Modelbouw Chicco
- Modelbouw KidKraft
- Modelbouw BRIO
- Modelbouw Brawa
- Modelbouw Carson
- Modelbouw ISDT
- Modelbouw Heller
- Modelbouw Baufix
- Modelbouw LGB
- Modelbouw Woodland Scenics
- Modelbouw Snap Circuits
- Modelbouw BIG
- Modelbouw Discovery
- Modelbouw Quercetti
- Modelbouw Siku
- Modelbouw MBZ
- Modelbouw Seuthe
- Modelbouw Metal Earth
- Modelbouw E-Blox
- Modelbouw Piko
- Modelbouw Fleischmann
- Modelbouw Tams Elektronik
- Modelbouw Roco
- Modelbouw Proses
- Modelbouw NOCH
- Modelbouw Massoth
- Modelbouw Trix
- Modelbouw Italeri
Nieuwste handleidingen voor Modelbouw
13 December 2024
13 December 2024
13 December 2024
13 December 2024
13 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024
11 December 2024