SAB Heli Division Head HPS2 - H0428 Handleiding
SAB Heli Division
Modelbouw
Head HPS2 - H0428
Lees hieronder de 📖 handleiding in het Nederlandse voor SAB Heli Division Head HPS2 - H0428 (2 pagina's) in de categorie Modelbouw. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
Center Hub
(H0411-S)
Linkage Rod
M3x50mm
(H0417-S)
Plastic Ball Link
(H0402-S)
Main Blade Grip
(H0182-S)
Bearing
10x
19x5mm
(HC422-S)
Blade Grip Arm
(H0183-S)
Plastic Ball Link
(H0402-S)
M4x24mm
(HC111-S)
M3x12mm
(HC062-S)
Nut M4
(HC212-S)
Approx
66mm
Spindle
(H0412-S)
Uniball Radius Arm Assembly ... x 2
Main Blade Grip Assembl
y ....x2
Note
: Larger ID Inside
Socket Head Cap Screw
Shouldered M4x25mm
(HC110-S)
Socket Head Cap
Screw M6x10mm
(HC124-S)
Oring
(HA024)
Metric Hex
Nylon Nut M4
(HC218-S)
Washer
6x
14 x1mm
(HC194-S)
Washer
10x
16x1mm
(HC230-S)
Thrust Bearing
10x
18x5.5mm
(HC438-S)
Socket Head Cap
Screw M3x16mm
(HC068-S)
Washer
3x
4x0.5mm
(HC176-S)
Swashplate Assemly
Center Hub Assembly
Radius Arm
(H0132-S)
Uniball Radius Arm
(H0205-S)
Flanged Bearing
3x
7x3mm
(HC402-S)
Flanged Bearing
2.5x
6x2.5mm
(HC400-S)
Spacer Arm
2.5x
4x6.3mm
[H0253]
Spacer Arm
3x
5x2.7mm
[H0134]
Main Blade Grip
Assembly
Bearing
10x
19x5mm
(HC422-S)
Approx 76mm
Radius Arm Assembly ... x 2
Uniball M3
5H18
(H0063-S)
Swashplate
Assemly
(H0422-S)
Linkage Rod A Assembly . . . .x2
Radius Arm
Assembly
(H0132-S)
Linkage Rod A
Assembly
(After a few flights, please check the preload
you can add HC232 if the preload has changed.)
Linkage Rod B
Assembly
(Initial length for the rods from the
swashplate to the Blade Grip.)
(to adjust the tracking,
turn this linkage.)
H0428M_Rev01
eg: Microlube GL261
Pin 5 mm
(H0413-S)
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
Damper
(H0426-B)
Uniball M3
(H0065-S)
Socket Head Cap
Screw M4x10mm
(HC102-S)
Socket Head Cap
Screw M2.5x18mm
(HC032-S)
Uniball Radius Arm
Assembly
[HC230-S] [HC232-S]
Socket Head Cap
Screw M3x12mm
(HC062-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Uniball M3
(H0437-S)
Please read this user manual carefully, it contains instructions for the correct assembly of the KIT.
Please refer to the website www.goblin-helicopter.com for updates and other important information. Thanks You.
Socket Head Cap
Shouder M5x35mm
(HC116-S)
Metrix Head
Nylon Nut M5
(HC218-S)
Blade
Washes
(H0158-S)
Page 1
[
H0428-K
]
B
Swashplate
[H0422-S]
- 1 x Swashplate Assembly.
- 2 x Bearings 30x
37x4mm.
- 6 x Uniballs M3x4
5 H3.
- 1 x Uniball M3x4
5 H18.
- 3 x Socket Head Cap
Screws M2x5mm.
- 4 x Socket Head Cap
Screws M2x8mm.
- 3 x Swasher
2x
5x0.5mm
Radius Arm
[H0132-S]
- 1 x Center Hub.
- 2 x Socket Head Cap Screws
M3x12mm.
- 1 x Socket Head Cap Screws
Shouldered M4x25mm.
- 1 x Metric Hex Nylon Nut M4.
Center Hub
[H0411-S]
- 2 x Radius Arms.
- 2 x Spacer Arm
3x
5x2.7mm.
- 2 x Spacer Arm
2.5x
4x6.3mm.
- 2 x Uniball Radius Arms.
- 2 x Socket Head Cap Screws M3x16mm.
- 2 x Socket Head Cap Screws M2.5x18mm.
- 2 x Washers
3x
4x0.5mm.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
- 2 x Flanged Bearings
3x
7x3mm.
Linkage
[H0417-S]
- 2 x Linkages
M3x50mm.
- 4 x Plastic Ball Links.
Damper Derlin
[H0426-S]
- 3 x H0426-A.
- 3 x H0426-B.
- 3 x H0426-C.
- 3 x Washers
10x
16x1mm.
- 3 x Washers
10x
16x0.2mm.
- 3 x Orings 3050.
Recommendations
- These parts should be used only with models SAB Goblin
- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapther 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and the O-Ring.
- Check for axial play of the spindle at least after the first 10 flights and add shims if necessary.
- Firmly tighten the blades before flight.
ABOUT HPS2
The new HPS 2 head offers an independent dampening system
for each blade grip, there are three dampening settings:
A = Soft for smooth response.
B = Medium.
C = Firm for direct and precise response.
We recommend starting with the medium setting.
For safety reasons we suggest to not exceed 2300 rpm.
Spare Parts
- 2 x Blade Grip.
- 2 x
Thrust Bearing
10x
18x5.5mm.
- 4 x
Bearing
10x
19x5mm.
- 2 x Washer
10x
16x1mm.
- 2 x Buttom Head Cap Screw M4x8mm.
Blade Grip
[H0182-S]
- 2 x Blade Grip Arm.
- 2 x Socket Head Cap
Screw M4x10mm.
- 2 x Uniball M3x3.5 Ø5 H5.5.
Blade Grip Arm
[H0183-S]
Spindle Shaft
[H0412-S]
- 2 x Spindle Shaft.
- 2 x Pin 5mm.
- 4 x Socket Head Cap
Screw M2.5x6mm.
- 2 x Socket Head Cap
Screw M6x10mm.
- 2 x Washer Ø6,3xØ15x1.
Uniball M3x3.5 Ø5 H5.5
[H0437-S]
- 2 x Uniball M3x3.5x
5H5.5.
TIPS:
RECOMMENDATIONS
- These parts should be used only with models
SAB Goblin 630, 700, 770, Speed, URUKAY
- Please follow all the instructions shown in the
Goblin main manual. In this manual please read
Chapter 2, Important notes
- Use Loctite on all threads.
- Put a small amount of grease inside the hub and
the O-Ring.
- Check the spindle for axial play at least after the
first few flights and add shims as necessary,
slight axial preload is optimal.
The blade grips must move freely, but they
should not move just under their own weight.
- Firmly tighten the blades before flight.
Left Side
Right Side
* To remove the dampeners,
you can use a flathead screwdriver
through the hole as shown.
* Clock-wise, counter clock-wise thread
* By turning the linkages you can adjust tracking.
If tracking is adjusted correctly, you’ll see the metal
part line up around in the center of the opening.
Detail B
SPARE PARTS
Page 2
Product specificaties
| Merk: | SAB Heli Division |
| Categorie: | Modelbouw |
| Model: | Head HPS2 - H0428 |
Heb je hulp nodig?
Als je hulp nodig hebt met SAB Heli Division Head HPS2 - H0428 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Modelbouw SAB Heli Division
10 Juli 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023
10 Juli 2023
Handleiding Modelbouw
- Modelbouw Lego
- Modelbouw Blade
- Modelbouw FALLER
- Modelbouw Geomag
- Modelbouw Graupner
- Modelbouw Kibri
- Modelbouw Marklin
- Modelbouw Mega Bloks
- Modelbouw Multiplex
- Modelbouw Playmobil
- Modelbouw Pocher
- Modelbouw Reely
- Modelbouw Revell
- Modelbouw Robbe
- Modelbouw Viessmann
- Modelbouw Voltcraft
- Modelbouw Wiking
- Modelbouw Wilesco
- Modelbouw Chicco
- Modelbouw KidKraft
- Modelbouw BRIO
- Modelbouw Brawa
- Modelbouw Carson
- Modelbouw ISDT
- Modelbouw Heller
- Modelbouw Baufix
- Modelbouw LGB
- Modelbouw Woodland Scenics
- Modelbouw Snap Circuits
- Modelbouw BIG
- Modelbouw Discovery
- Modelbouw Quercetti
- Modelbouw Siku
- Modelbouw MBZ
- Modelbouw Seuthe
- Modelbouw Metal Earth
- Modelbouw E-Blox
- Modelbouw Piko
- Modelbouw Fleischmann
- Modelbouw Tams Elektronik
- Modelbouw Roco
- Modelbouw Proses
- Modelbouw NOCH
- Modelbouw Massoth
- Modelbouw Trix
- Modelbouw Italeri
Nieuwste handleidingen voor Modelbouw
19 November 2024
14 November 2024
12 November 2024
30 September 2024
Italeri Scania R730 V8 Streamline ‘‘Silver Griffin’’ Handleiding
5 September 2024
30 Juli 2024
30 Juli 2024
4 Mei 2024
4 Mei 2024
3 Mei 2024