Rupert Neve Designs Portico II Handleiding

Rupert Neve Designs Processor Portico II

Lees hieronder de 📖 handleiding in het Nederlandse voor Rupert Neve Designs Portico II (22 pagina's) in de categorie Processor. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/22

Operations Manual

By:

Serial #:

Portico II Channel User Guide

Thank you for your purchase of a Portico II Channel module.

Everyone at Rupert Neve Designs hope you enjoy using this tool as much as we have enjoyed

designing and building it. The name “Portico II” will be used for a series of new ultra-high end

professional products that will share some traits. Please take note of the following list of safety concerns

and power requirements before the use of this or any Portico II Series product.

Safety

It’s usual to provide a list of “do’s and don’ts” under this heading but mostly these amount to

common sense issues. However, here are important safety requirements that must be adheared to:

Heat generated by the Channel module is radiated through the case work and by convection through the

ventilation holes, therefore the holes should not be covered or blocked. To avoid overheating,

Portico II units should not be stacked immediately above or adjacent to other equipment that

gets hot, and one rack space above the unit should be left open for heat ventilation.

Also bear in mind that other equipment may radiate strong hum elds which could spoil

the performance of your Portico II module.

Protect the power cord from being walked on or pinched, particularly at plugs convenience receptacles

and the point where they exit from the apparatus. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third prong are provided for

your safety. Unplug the module during lightning storms or when unused for long periods of time.

Don’t operate your Portico II module in or around water! Electronic equipment and liquids are not

good friends. If any liquid is spilled, such as soda, coffee, alcoholic or other drink, the sugars and

acids will have a very detrimental effect. Sugar crystals act like little rectiers and can produce

noise (crackles, etc.). SWITCH OFF IMMEDIATELY because once current starts to ow the

mixture hardens, can get very hot (burnt toffee!) and cause permanent and costly damage. If it gets

wet and you suspect that good clean water may have gotten in, immediately unplug the unit, and

remove it from the source of water. Please contact support as soon as possible at

support@rupertneve.com for resolution. Clean only with dry cloth.

Don’t be tempted to operate a Portico II unit with the cover removed. The cover provides magnetic

screening from hum and R.F. stray elds.

Power Requirements

Each Portico II unit has a high quality, low noise switching power supply that is further ltered and shunt

regulated for an exceptionally quiet and reliable power source for the audio circuits. The power sup-

ply is considered “universal” in the sense that it will accept 100V through 240V AC and complies with

standard mains voltages around the world. Be absolutely sure to disconnect mains power (remove the

power cable from the IEC power connector at the back panel) before checking the fuse. The fuse is lo-

cated in the IEC power input connector and is accessed by opening the small panel labeled “FUSE”. The

fuse should always be replaced with the correct value and type. The Portico II power supply requires a

5x20 mm 2.5 amp fast acting ceramic body fuse Bussman type GDA 2.5A or equivalent.

The fuse is a protection device intended to prevent additional damage or hazard if the Portico II unit de-

velops a problem. However sometimes a fuse may “pop” due to a mains surge and need to be replaced

(it probably did protect the Portico II). The symptom of a blown fuse is simply that the unit does not

power up. Disconnect the power cable, try replacing the fuse, re-insert the power cable, push the “Pow-

er” button. If this does not solve the problem or the fuse “pops” again there may be a problem with the

Portico II you should contact your dealer or email < > or support@rupertneve.com phone 512-847-3013.

Gain

0-66dB

Detect

Line Trim

+/-6dB

HPF

EQ Pre / Post

EQ Compressor

Phase

Reverse

LF In

LMF / HMF

In HF In

GR METER

Comp In

Silk

Silk +

Texture

Mute

Output

METER

Send

Return

LinkSidechain

All EQ

From

Sidechain

S/C

HPF

(Auto)

De-ess

HMFLMF HF

Output

+48V

PORTICO II

CHANNEL STRIP

Portico II Channel: Block Diagram

Product specificaties

Merk:	Rupert Neve Designs
Categorie:	Processor
Model:	Portico II

Heb je hulp nodig?

Als je hulp nodig hebt met Rupert Neve Designs Portico II stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Processor Rupert Neve Designs

Rupert Neve Designs 5254 Handleiding

4 Juni 2023

Rupert Neve Designs Portico 542 Handleiding

25 April 2023

Rupert Neve Designs 5045 Handleiding

5 April 2023

Rupert Neve Designs Portico 543 Handleiding

27 Februari 2023

Rupert Neve Designs Portico II Handleiding

21 Januari 2023

Handleiding Processor

Nieuwste handleidingen voor Processor

Decimator DMON-QUAD Handleiding

10 December 2024

ART Pro Channel III Handleiding

10 December 2024

TC Helicon SWITCH-3 Handleiding

7 December 2024

TC Helicon SWITCH-6 Handleiding

7 December 2024

Intel Core i5-10500 Handleiding

30 November 2024

HP Intel Xeon X5670 Handleiding

23 November 2024

Smart-AVI EZW-UH9 Handleiding

20 November 2024

Christie Spyder X80 Handleiding

19 November 2024

Tascam MM-4D/IN-E Handleiding

18 November 2024

Intel Core i5-10400F Handleiding

16 November 2024