RCA RT2390 Handleiding

RCA Home cinema set RT2390

Lees hieronder de 📖 handleiding in het Nederlandse voor RCA RT2390 (2 pagina's) in de categorie Home cinema set. Deze handleiding was nuttig voor 84 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

7. Adjustment Buttons

• Press the Left or Right buttons to select

among setting items in setup mode: SLEEP,

DIMMER, SPEAKER DISTANCE, SPEAKER

SETUP, and audio input source (ANALOG,

OPTICAL / COAXIAL).

• Press the Up or Down buttons to adjust the

values when the display shows the setup you

want to change.

8. SURROUND

Selects among surround sound settings: DOLBY

PL II EMULATION, DOLBY PL II MUSIC, DOLBY

PL II MOVIE, STEREO, DISCO, STADIUM,

THEATER, JAZZ CLUB, ARENA, 3 STEREO.

9. EQUALIZER

Selects among preset equalizer modes.

(only available in stereo mode)

10. NIGHT

Selects among Night mode options (DRC OFF,

SOFT and ON) which compresses the volume

difference between normal voices and sounds

such as explosions. (Available only during

Dolby digital signal playback)

11. LEVEL

Speaker LEVEL setting and Test tone. Refer to

“Advanced Sound Control” for details.

12. SUBWOOFER

Selects among subwoofer output level (SOFT

SUBWOOFER, BALANCED SUBWOOFER,

STRONG SUBWOOFER, POWERFUL

SUBWOOFER).

13. Number Buttons

Directly access a preset station in Tuner mode.

14. SETUP

Enters Setup mode. Use the Left and Right

adjustment buttons to select among setup

options. (SLEEP, DIMMER, FRONT SPK

DISTANCE, CENTER SPK DISTANCE, SURROUND

SPK DISTANCE, CENTER SPK ON/OFF,

SURROUND SPK ON/OFF, DIGITAL INPUT).

15. Operation Buttons

In TUNER mode:

• Press the TUNER - and TUNER + keys to tune

down or up the radio frequency.

• Press SAVE to activate the preset station

saving and press to confirm preset station

settings.

• PLAY, RECORD, STOP and PAUSE keys are only

for easy control of external devices that are

connected to your receiver such as CD, VCR,

DVD, TAPE, etc.. The remote control currently

operates most Thomson, RCA and GE products.

Display

DVD / VCR / SAT / TUNER / TAPE / CD / TV

• An arrow points to the current source mode.

• Dolby Digital audio input for signal

format.

• Dolby Pro Logic II audio output

format.

FM / AM

• Radio band indicator in Tuner mode.

• Tuner stereo signal detected.

OPT12

• Optical digital input detected.

COAX

• Coaxial digital input detected.

TUNED

• Tuner station detected.

• Speaker Icons.

L - Front left speaker

C - Center speaker

R - Front right speaker

LS - Left surround (rear) speaker

RS - Right surround (rear) speaker

LFE - Subwoofer speaker

SLEEP

• Unit in Sleep mode.

MEMORY

• Unit is in Tuner Preset Station mode.

KHz / MHz

• Tuner frequency unit.

Switching the unit on and off

• To switch on the receiver, press the

STANDBY/ON button on the main unit once,

or the ON•OFF button on the remote

control.

• Standby: when the receiver is in tuner

mode, press the STANDBY/ON button once

to enter standby mode.

On the remote control, press the ON•OFF

button twice within 2 seconds if the receiver

is not in Tuner source mode to enter standby

mode.

To avoid entering standby mode when

powering up the unit, do not press the

ON•OFF button twice within 2 seconds.

• The receiver draws a small amount of

electricity when in standby mode.

Unplugging the unit from the wall

socket will stop the draw.

Selection of source

When one of the source button is pressed, the

input corresponding to the name will be

activated.

The receiver acts as a switching device between

all the sources that are plugged into it.

u s e r

m a n u a l

EXPORTER

Thomson Inc.

P.O. Box 1976

Indianapolis, IN 46206 - 1976

Trademark(s) ® Registered

Marca(s) Registrada(s)

Marque(s) Deposée

55984640 (EN)

www.rca.com

Printed in China / Impreso en China

IMPORTADOR

Comercializadora Thomson de México,

S.A. de C.V.

Álvaro Obregón No. 151. Piso 13.

Col. Roma. Delegación Cuauhtémoc

C.P. 06700. México, D.F.

Telefono: 52-55-11-020360

RFC: CTM-980723-KS5

RT2390

It is important to read this instruction book prior to using your new product for the first time.

Es importante leer este manual antes de usar por vez primera su euipo.

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation.

In accordance with FCC requirements, changes

or modifications not expressly approved by

Thomson Inc. could void the user’s authority to

operate this product.

This device generates and uses radio frequency

(RF) energy, and if not installed and used

properly, this equipment may cause

interference to radio and television reception.

If this equipment does cause interference to

radio or television reception (which you can

determine by unplugging the unit), try to

correct the interference by one or more of the

following measures:

• Re-orient the receiving antenna (that is, the

antenna for the radio or television that is

"receiving" the interference).

• Move the unit away from the equipment

that is receiving interference.

• Plug the unit into a different wall outlet so

that the unit and the equipment receiving

interference are on different branch circuits.

If these measures do not eliminate the

interference, please consult your dealer or an

experienced radio/television technician for

additional suggestions.

Also, the Federal Communications Commission

has prepared a helpful booklet, "How To

Identify and Resolve Radio TV Interference

Problems." This booklet is available from the

U.S.

Government Printing Office, Washington, DC

20402. Please specify stock number 004-000-

00345-4 when ordering copies.

This product complies with DHHS Rules 21 CFR

Subchapter J. Applicable at the date of

manufacture.

Technical Specification

Product: Dolby Digital Audio Receiver

Brand: RCA

Model: RT2390

Electrical current consumption

Power Supply: 120V ~ 60Hz

Power consumption: 135 Watts

IMPORTER

Comercializadora Thomson de México, S.A. de

C.V.

Álvaro Obregón No. 151. Piso 13.

Col. Roma. Delegación Cuauhtémoc

C.P. 06700. México, D.F.

Telefono: 52-55-11-020360

RFC: CTM-980723-KS5

For Your Safety

The AC power plug is

polarized (one blade is wider

than the other) and only fits

into AC power outlets one

way. If the plug won’t go into

the outlet completely, turn

the plug over and try to insert

it the other way. If it still won’t fit, contact a

qualified electrician to change the outlet, or

use a different one. Do not attempt to bypass

this safety feature.

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

For Your Records

In the event that service should be required,

you may need both the model number and the

serial number. In the space below, record the

date and place of purchase, and the serial

number:

Model No.

Remote Control No.

Date of Purchase

Place of Purchase

Serial No.

Service Information

This product should be serviced only by those

specially trained in appropriate servicing

techniques. For instructions on how to obtain

service, refer to the warranty included in this

Guide

FCC Information

WARNING:

TO PREVENT FIRE OR ELECTRICAL

SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THE EX CLAMATION

POINT WI T HIN THE

T R I A N G L E I S A

WARNING SIGN

ALERTING YOU OF

I M P O R T A N T

I N S T R U C T I O N S

A C C O M PA N Y I N G

T H E P R O D U C T.

T H E L I G H T N I NG

FLASH AND ARROW-

HEAD WITHIN THE

T RI A NG L E I S A

WA R N I N G S I G N

ALERTING YOU OF

" D A N G E R O U S

VOLTAGE " INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK,

DO N OT R EM OV E C OV ER

( O R B A C K ) . N O U S E R -

S E RV I C EA BL E PA R TS I N-

S ID E. R EF E R S E R V IC IN G

TO Q U A LI F I E D S E R V I C E

PERSONNEL.

Unpacking the Receiver

You should recive the following items:

• One receiver unit

• One pair of “AAA” batteries

• One pig-tail antenna wire

• One external AM loop antenna

• One instruction book;

• One safety leaflet

• One Quick Connection Guide

• One Remote Control

Unpacking The Speakers

One set of speakers including:

• 1 set of left and right front speakers,

• 1 centre speaker,

• 1 subwoofer and

• 1 set of left and right rear speakers

• 6 speaker wires including:

- 1 X green/grey striped wire for

center speaker

- 1 X red/grey striped wire for front

right speaker

- 1 X white/grey striped wire for front

left speaker

- 1 X purple/grey striped wire for

subwoofer

- 1 X blue/grey striped wire for rear

left speaker

- 1 X gray/grey striped wire for rear

right speaker

Inserting Batteries into Remote

Control

Insert two “AAA” (R03) batteries according to

the + and - signs in the battery compartment.

To use the remote control, point it directly at

your receiver.

Install batteries as follows:

1. Remove battery compartment door by

applying thumb pressure on battery door and

then lift the door out and off the cabinet.

2. Insert 2 AAA batteries in the compartment

and replace the compartment door.

Set up and Maintenance of the

Receiver

Provide spaces for sufficient ventilation as

indicated:

• Do not connect to the AC power cords until

all connections are completed.

• Do not use your set immediately after

transferring it from a cold place to a warm

place: there is risk of condensation.

• Do not expose your set to water and

excessively high temperatures.

• After having disconnected your set, clean the

case with a soft cloth, or with a slightly damp

leather chamois. Never use strong solvents.

Protect your Components from

Overheating

• Do not block ventilation holes in any

component. Arrange the components so that

air can circulate freely.

• Do not stack components directly on top of

each other.

• Do not place the unit near other components

that generate heat such as heating vents.

• Allow adequate ventilation when placing

your components in a stand.

• Place an amplifier near the top shelf of the

stand so heated air rising from it will not

affect other components. If you have a

satellite receiver, you should place it on the

top shelf.

10 cm/4"

5 cm/

10 cm/4"

10 cm/

Front View

Side View

Connecting to Audio Components

AUDIO INPUT

DVD SAT TV VCR CD TAPE DIGITAL AUDIO

COAXIAL OPTICAL

VCR

CD Player

SAT

to LINE OUT (Tape Deck)

to AUDIO OUT (CD)

to AUDIO OUT (SAT)

to AUDIO OUT

(DVD)

to AUDIO OUT (TV)

to AUDIO OUT (VCR)

Tape Deck

DIGITAL INPUT

Connect components capable of

outputing Dolby Digital (e.g. DVD or

SAT) or standard PCM (CD) format

digital signals. Read section on

"Input Signal Setting" under

"Advanced Sound Control" carefully

to adjust the matching input

settings.

If your CD player is equipped with digital optical

jacks, use of optical cable is preferred. What you

need is just one more optical digital connecting

cable (not supplied). Plug it in the digital input jack

of the receiver and select OPTICAL on the receiver

setting (see details under "Input Signal Setting").

You can enjoy better sound quality brought to you by

the optical cable. When optical cable is used, analog

cables are still needed for recording to tape output.

DVD

DIGITAL CONNECTION

If you have a SAT receiver DVD player or CD player with a digital output, you can make use of an optical digital cable (not

supplied) or coaxial digital cable (not supplied) to carry the audio portion of the signal and enjoy Dolby Digital sound quality.

One optical or coaxial cable is needed for each SAT receiver, DVD player or CD player. When optical or coaxial cable is used,

the analog audio cables are still needed if recording through a tape or VCR is desired. This receiver provides one optical and

one coaxial digital input for the connection of your components. Please connect your components (e.g. DVD, SAT or CD) to the

appropriate digital inputs and press DIGITAL INPUT to select the corresponding digital input source.

Note: Optical and coax cables carry only the audio portion of the signal. A video connection must also be established for a SAT

receiver and DVD player.

Digital Connections

Read instructions carefully when

connecting components to the receiver.

Digital In Jacks can accept Dolby Digital (AC-3)

or PCM signals when compatible components

are connected.

TV Connections

TVs with RF input may need a RF modulator

(not included) for inputting audio signals.

Connecting the Antennas

The AM and FM antennas connect to the AM

and FM terminals on the system’s back panel.

They must be hooked up in order to receive

clear reception.

AM Loop Antenna and FM Indoor

Antenna

1. Uncoil the Antenna wire and locate the base

end of the AM antenna.

2. Press down on the Antenna tab to open the

terminal.

3. Inert the antenna wires into the terminal

and release the tabs to secure the wires in

place.

Connecting for Power

Make sure you connect all

your other electronic

components and the speakers

before plugging your receiver

into the outlet. Plug the

power cord in the wall outlet,

matching the wide blade of

the plug with the wide slot in the outlet. Be

sure to insert the plug completely.

Using Headphones

To listen privately through

your audio system, use the

PHONES jack on the receiver.

However, make sure you turn

down the volume before you

put on the headphones.

Increase the volume to the

desired level after

headphones are in place.

Once headphones are connected,

“HEADPHONE DOWN MIX 2 CHANNEL” will

scroll on display. This feature automatically

converts multi-channel speaker outputs to 2

channel stereo for your listening pleasure.

Hearing Comfort & Well-Being

• Do not play your headset at a high volume.

Hearing experts advise against continuous

extended play.

• If you experience a ringing in your ears,

reduce volume or discontinue use.

Factory Setting

The unit is preset to the following settings

when you first power the receiver up right out

of the box:

Function = TUNER

Volume setting = 25

Bass & treble = 0 dB

EQ - FLAT

Speaker settings: Center, surr = YES

Subwoofer = STRONG

DRC = OFF

Reset to Factory Settings

You may restore factory setting with the

following procedures:

1. Enter SAT mode.

2. Press PRESET UP, PRESET DOWN, SOURCE

UP to reset the unit.

All preset stations will reset to FM87.5MHz and

all receiver settings restore to default settings

as described above.

FM 75‰

3‰

FR FLSR SLCENSUB

6‰

SPEAKERS

DIGI TAL AUDI O

COAXIAL OPTICAL

GND AM LOOP

SAT / DVD / CD Player / TV

COAXIAL DIGITAL IN (AUDIO)

Connect to coaxial digital output of

DVD, CD, SAT or other compatible

devices.

OPTICAL DIGITAL IN (AUDIO)

Optical Fiber Cable

Connect to optical digital output of

DVD, CD, SAT or other compatible

devices.

DVD / CD / SAT

DIGITAL AUDIO

COAXIAL OPTICAL

AUDIO INPUT

DVD SAT TV VCR C D TAPE

SUBWOOFER

AUDIO OUT

RF modulator

RF cable

Audio cable

The diagram shown above may varies from your actual RF

modulator, please refer to your RF modulator manual.

Audio in

Audio out

RF in RF out

HINT

• For FM reception, extend antenna to its

full length.

• For AM reception, rotate the antenna

horizontally to get better reception.

Getting Started

Dolby and the double-D symbol are

registered trademarks of Dolby

Laboratories.

NOTE

STRONG SUBWOOFER setting makes the

output level of subwoofer speaker to be

stronger than normal Dolby setting. Adjust

the SUBWOOFER setting by pressing the

SUBWOOFER key to achieve the best bass

performance.

WARNING

All preset radio stations and surround

sound setting will be lost after factory

setting is restored.

Operating Your Receiver

NOTE

The remote control button CLEAR, MENU

and GUIDE do not function for this receiver

but can be used to control other RCA and

Thomson products.

SS RS

RSRS

LS RS

LFE

RCL

Example 1:

If you have connected a DVD player to the DVD

input on the receiver, press the SOURCE

buttons on the main unit repeatedly until DVD

is selected or press on the remoteDVD•6CH

control to receive the sounds and images

transmitted by the DVD.

Example 2:

Based on the example 1, the DVD is playing , if

a VCR is connected to the VCR input of the

receiver, press the buttons on theSOURCE

main unit repeatedly until VCR is selected or

press AUX 1 (VCR) on the remote control. The

sound from the VCR source will replace the

DVD.

You can connect up to 6 audio sources to this

amplifier:

Source button Corresponding connector

(receiver front panel) (receiver back panel)

- DVD DVD IN

- SAT SAT IN

- TV TV IN

- VCR VCR IN

- CD CD IN

- TAPE TAPE IN

- FM/AM built-in

An arrow points to the source name selected

shown on the display.

Example: Press to select DVD as theDVD

source to the amplifier.

Using the Remote to Control

Additional Components

You can use your remote to control most of

RCA branded VCRs, satellites, cable boxes or

TVs.

Press the corresponding source button on the

remote control to operate options on other

components.

Volume Punchthrough

By default, the VOL+ VOL- / and MUTE buttons

will only control the receiver, regardless which

mode (TV, VCR, etc) the receiver is in.

By programming the volume punchthrough

function, you can also control the volume of

the TV.

To activate the volume punchthrough function,

follow the procedures below:

1. Press and hold the VOL- button.

2. While holding down the button, press VOL-

one of the source buttons to select the

source where you want to control TV volume

at. (DVD TV, , VCR or SAT•CABLE)

3. Continue holding down the button and VOL-

press the TV button once.

4. Release all buttons.

You should now be able to control TV volume

and mute at the selected device.

Using the receiver to play a source

After having properly connected a source (DVD,

CD, VCR) to the receiver, you can partly control

them through the receiver.

Playing a DVD with the receiver

1. Connect a DVD player to the receiver (see

connecting your receiver for details).

2. Press ON/STANDBY on the main unit or press

ON•OFF on the remote control to switch on

the receiver.

3. Press the SOURCE buttons on the main unit

or DVD•6 CH on the remote control to select

the DVD source.

4. Switch ON the DVD player and start

playback.

5. Switch ON your TV.

6. Select the appropriate A/V channel on the TV

(refer to your TV manual for details) until the

image from the DVD player is displayed.

7. Set the sound Mode if needed (see

"Advanced sound control" for details).

Example 1:

To play Dolby Prologic II Movie sound, press

the SURROUND buttons until "Dolby PL II

MOVIE" appears on the Display and all of the

speaker'’ icons light up.

Example 2:

LD: You may need to select a different Audio

Channel on your LD (refer to your LD player

manual).

8. Adjust the volume knob accordingly.

Receiver Controls

1. ON/STANDBY

Turns the unit on and off. When the

system is turned on, the unit will go to the

mode it was in before powered off.

2. Display

Displays current status of the receiver.

3. SUBWOOFER

Selects among subwoofer sound level.

(SOFT SUBWOOFER, BALANCED SUBWOOFER,

STRONG SUBWOOFER, POWERFUL

SUBWOOFER)

4. SOURCE Buttons

Selects sound source. (DVD, Tuner, Tape, VCR,

CD, TV and SAT)

5. SURROUND Buttons

Selects digital sound processor.

(DOLBY PL II MOVIE, STEREO, DISCO,

STADIUM, THEATER, JAZZ CLUB,

ARENA, 3 STEREO, DOLBY PL

EMULATION, DOLBY PL II MUSIC)

6. PRESET Buttons

Selects preset station in Tuner mode.

7. VOLUME

Increases and decreases volume level

8. PHONES

Plug your headphones (not supplied)

into it for your private enjoyment.

Speakers will be off when phones

are inserted.

Remote Control

Please be sure you have inserted the batteries

into the remote control. You can test it by

pressing any button.

1. ON•OFF

Turns the receiver and other auxiliary

components on and off. (see “Using the

Remote to Control Additional Components”).

2. Source Buttons

Selects various audio sources.

3. VOL + / VOL -(Volume Buttons)

Adjusts the volume level.

4. CH+ / CH- (Channel Buttons)

Selects programmed stations in TUNER mode.

5. MUTE

Mutes all audio output.

6. GO BACK / ST•MONO

• Selects between Stereo and Mono sound in

Tuner mode.

1 2 3

Operating Your Receiver Operating Your Receiver

NOTE

1. Your receiver has a built in tuner. Just

connect the appropriate antenna to the

back of the receiver and you will be

able to listen to radio stations. (See

details in Tuner section)

2. Other sources can be connected to the

above standard source. Example: you can

connect a LD into the DVD inputs.

3. Refer to the "Connecting To Audio

Components" section for details on

connection.

NOTE

The remote control can only operate RCA

brand products.

NOTE

Volume punchthrough can be done in all

non-Tuner modes.

NOTE

Controlling the TV volume can be done in

any non-Tuner modes.

HINT

To return to controlling receiver volume

and mute again, follow the steps above but

press TUNER instead of TV in step 3.

HINT

If batteries are removed from the battery

compartment of the remote control, the

volume and mute control in all source

modes will be the receiver volume and

mute conrol except in TV mode.

NOTE

To play Dolby Digital sound, the source

must be connected to the receiver via the

optical or coaxial terminal

NOTE

The system is equipped with Dolby Digital,

and manufactured under License from

Dolby Laboratories.

RT2390 EN sheet final 12/28/04 9:42 AM Page 1

Operating the Radio

The receiver has a built-in tuner that allows for

AM/FM radio function.

Manual tuning

1. Connect the FM and AM antenna accordingly

(see "Connecting the Antenna” section for

details)

2. Press ON/STANDBY on the main unit or

ON•OFF on the remote control to switch on

the receiver.

3. Press the SOURCE buttons on the main unit

until the tuner mode is selected or press

TUNER on the remote control.

4. To select between

FM and AM band,

press the TUNER

button repeatedly.

5. Tune to a station

by pressing TUNER

- or TUNER +

repeatedly until

the desired station

is found.

Automatic Tuning

Press and hold TUNER -

or TUNER + for about

one second to activate

the automatic SEARCH

function. The receiver

will automatically tune

frequencies until it

finds a station.

Select a sound effect if needed by pressing the

SURROUND button. (see "Advance sound

section" for details).

Selecting Mono or Stereo Sound

Press the ST•MONO

button on the remote

control to toggle

between mono and

stereo sound in FM

tuner mode (when

available).

Storing radio stations

The receiver can store up to 40 radio stations in

memory. You can enter every single radio

station yourself or the receiver can store all

available radio stations automatically in an

ascending order.

Automatic preset storing : (FM only)

1. In Tuner mode,

select the FM

band by pressing

TUNER on the

remote control.

2. Press and hold the button on the TUNER

remote control for 3 seconds. “MEMORY”

will be displayed in red and will blink during

the automatic storing process.

Radio frequencies will be scanned and radio

stations will be stored automatically. When all

available radio stations are stored or if all 40

memory locations are full, the auto preset will

stop.

Manual preset

1. Select FM or AM band by pressing

TUNER repeatedly.

2. Tune to the radio station to be stored.

(see "Manual tuning" above for details)

3. Press the SAVE

button on the

remote control.

"MEMORY" will

flash and a

preset number

will be shown on

the display.

4. While MEMORY

is still flashing on

the display, press

CH CHor

on the remote

control to select

the desired preset

memory location.

5. Press the SAVE button on the remote

control to store frequency in selected

preset location.

6. Repeat steps 1-5 to store other frequencies.

Retrieving preset stations

1. Press TUNER on the remote control to

select tuner mode.

2. Press the buttons on the main PRESET

unit or the CH or buttons CH

on the remote control to select the

preset station.

Receiver/Tuner Operation

ST indicator is off.

• Adjust the antenna.

• Press GO BACK/ST.MONO button to insure

you are not outputting in mono.

The signal is Mono. Severe hum or

noise.

• The signal is too weak. Connect an external

antenna.

• Adjust Antenna

• Reposition Antenna away from any

electronics.

There is interference to FM reception.

• Turn off other electrical units (e.g. DVD, CD

player) near the receiver.

Remote Control Operation

The remote control does not operate

the unit.

• Another source mode is selected on the

remote. Press the correct Source Button.

• No batteries installed. (included with your

system) Install the batteries before

attempting to operate the remote. Be sure to

match the + and - ends of each battery to

the symbols shown in the remote battery

compartment.

• The batteries are weak. Replace all batteries.

• The remote is not pointed at the remote

control sensor on the main unit or there is an

obstacle between the remote and the main

unit.

• The remote control is too far from the

main unit, move closer.

Remote loses Programmed codes.

• Weak batteries, replace batteries.

Remote forgets what source was

selected.

• Weak batteries, replace batteries.

General

No audio.

• Make sure the speakers are connected.

• Check the input connections.

• Check the power cord connections.

• Make sure the MUTE signal on the front

panel is off.

• Make sure the digital setting (optical, coaxial

or analog) is correct.

• Check that the headphone is not inserted.

No audio from one channel.

• Check the speaker level setting.

• Check the speaker wire or external source

cable connections.

Noise occurs when the TV is turned

on.

• The TV is too close to the audio system.

Specific instruments sound displaced.

• Check the connections between the

receiver and the speakers if the sound does

not match the video.

• Check if the video and audio cable are

correctly inserted.

Cleaning the Exterior

Disconnect the system from AC power before

cleaning the exterior of the system with a soft

dust cloth, or with a slightly damp leather

chamois. Never use strong solvents.

Disconnect the audio system from the power

source before performing any maintenance.

Cleaning

Clean the exterior of the system using a soft

dust cloth.

Important battery information

• Remove the batteries to avoid leakage if you

do not use your remote control for more

than one month.

• Discard leaky batteries immediately as

leaking batteries may cause skin burns or

other personal injuries.

• Dispose of batteries in the proper manner,

according to provincial and local regulations.

• Any battery may leak electrolyte if mixed

with a different battery type, if inserted

incorrectly, if all batteries are not replaced at

the same time, if disposed of in fire, or if an

attempt is made to charge a battery not

intended to be recharged.

Safety precautions

• Never open the cabinet under any

circumstances. Any repairs or internal

adjustments should be made only by a

trained technician.

• Never operate this product with the cabinet

removed.

• Do not touch the player with wet hands. If

any liquid enters the player cabinet, take the

player to a trained technician for inspection.

• The apparatus shall not be exposed to

dripping and splashing.

• No object filled with liquids, such as vases,

shall be placed on the apparatus.

• No naked flame sources such as lighted

candles ,shall be placed on the apparatus.

Headset safety

• Do not play your headset at a high volume.

Hearing experts warn against extended high-

volume play.

• If you experience a ringing in your ears,

reduce volume or discontinue use.

• You should use extreme caution or

temporarily discontinue use in potentially

hazardous situations.

• Even if your headset is an open-air type

designed to let you hear outside sounds,

don’t turn up the volume so high that you a

re unable to hear what is around you.

Don’t infringe

This product should only be used for the

purposes for which it is sold, that is,

entertainment, violating no copyright law. Any

attempts to use this product for which it is not

intended is unlawful and therefore not

condoned by Thomson.

Equipment Specifications:

AMPLIFIER SECTION:

RMS Output Power: Dolby Digital Mode with

10% Total Harmonic Distortion

Rear Channels: 55 Watts each Channel (1KHz, 6

Ohm)

Front and Center Channel: 98 Watts (1KHz, 3

Ohm)

Subwoofer Channel: 98 Watts (100Hz,

3 Ohm)

Total RMS Output Power, Dolby Digital mode :

500 W

FTC Output Power: Dolby Digital Mode with

10% Total Harmonic Distortion

Front Channels (L and R ): 50 Watts per

Channel (1KHz, 3 Ohm)

Rear Channels (L and R): 45 Watts per Channel

(1KHz, 6 Ohm)

Center Channel: 90 Watts (1KHz, 3 Ohm)

Subwoofer Channel: 90 Watts (80Hz, 3 Ohm)

Total FTC Output Power, Dolby Digital mode:

370 Watts

Muting Attenuation: 65dB

Frequency Response: 20kHz /-3dB, 1kHz ref.

Subwoofer Frequency Response: 10 Hz / -3db,

80Hz ref.

Signal to Noise Ratio: 65dB (Dolby digital

mode)

Video Signal to Noise Ratio from 40 dB to 60dB

AM TUNER SECTION:

Frequency Response: 2kHz +/-6dB, 1kHz ref.

Usable Sensitivity: 800uV/m @ S/N 20dB

Signal to Noise: 38dB

IF Rejection: 35dB

FM TUNER SECTION:

Frequency Response: 15kHz +/-3dB, 1kHz ref.

Quieting: 24dBu

Signal to Noise: 60dB(stereo) / 65dB(mono)

IF Rejection: 50dB

Dimensions (H x W x D inch) :

Unit - 3.7 x 16.9 x 14

Front and Surround Speakers - 6.1 x 3.1x 3.5

Center Speaker - 2.7 x 9.8 x 33.3

Subwoofer - 12.4 x 6.3 x 14

What your warranty covers:

• Defects in materials or workmanship.

For how long after your purchase:

• One year from date of purchase for labor

and parts

• The warranty period for rental units begins

with the first rental or 45 days from date of

shipment to the rental firm, whichever comes

first.

What we will do:

• Pay any Authorized RCA Audio Service

Center the labor charges to repair your unit.

• Pay any Authorized RCA Audio Service

Center for the new or, at our option,

refurbished replacement parts required to

repair your unit.

How you get service:

• Take your unit to any Authorized RCA Audio

Service Center. To identify your nearest

Authorized RCA Audio Service Center, ask your

dealer, look in the Yellow Pages, or call 1-800-

336-1900.

• Show the Authorized Service Center

Representative your evidence of purchase date

or first rental.

• Pick up your unit when repairs are

completed.

• Proof of purchase in the form of a bill of

sale or receipted invoice which is evidence that

the product is within the

warranty period must be presented to obtain

warranty service. For rental firms, proof of

first rental is also required.

What your warranty does not cover:

• Customer instruction. (Your Owner’s Manual

describes how to install, adjust, and operate

your unit. Any additional information should

be obtained from your dealer.)

• Installation and related adjustments.

• Signal reception problems not caused by

your unit.

• Damage from misuse or neglect.

• Cleaning of audio heads.

• Batteries.

• A unit that has been modified or

incorporated into other products or is used for

institutional or other commercial purposes.

• A unit purchased or serviced outside the

U.S.A.

• Acts of nature, such as but not limited to

lightning damage.

Product Registration:

• Please complete and mail the Product

Registration Card packed with your product. It

will make it easier to contact you should it ever

be necessary. The return of the card is not

required for warranty coverage.

Limitation of Warranty:

• THE WARRANTY STATED ABOVE IS THE

ONLY WARRANTY APPLICABLE TO THIS

PRODUCT. ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED

(INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE) ARE HEREBY

DISCLAIMED. NO VERBAL OR WRITTEN

INFORMATION GIVEN BY THOMSON INC.,

ITS AGENTS OR EMPLOYEES SHALL CREATE

A GUARANTY OR IN ANY WAY INCREASE

THE SCOPE OF THIS WARRANTY.

• REPAIR OR REPLACEMENT AS PROVIDED

UNDER THIS WARRANTY IS THE EXCLUSIVE

REMEDY OF THE

CONSUMER. THOMSON INC. SHALL NOT BE

LIABLE FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING

FROM THE USE OF THIS PRODUCT OR

ARISING OUT OF ANY BREACH OF ANY

EXPRESS OR IMPLIED WARRANTY ON THIS

PRODUCT. THIS DISCLAIMER OF

WARRANTIES AND LIMITED WARRANTY

ARE GOVERNED BY THE LAWS OF THE

STATE OF INDIANA. EXCEPT TO THE EXTENT

PROHIBITED BY APPLICABLE LAW, ANY

IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE

ON THIS PRODUCT IS LIMITED TO THE

APPLICABLE WARRANTY PERIOD SET FORTH

ABOVE.

How State Law relates to warranty:

• Some states do not allow the exclusion nor

limitation of incidental or consequential

damages, or limitations on how long an

implied warranty lasts, so the above limitations

or exclusions may not apply to you.

• This warranty gives you specific legal rights,

and you also may have other rights that vary

from state to state.

If you purchased your unit outside the

United States:

• This warranty does not apply. Contact your

dealer for warranty information.

Service calls which do not involve

defective materials or workmanship are

not covered by this warranty. Costs of

such service calls are the sole

responsibility of the purchaser.

What your warranty covers:

• Defects in materials or workmanship.

For how long after your purchase:

• One year from date of purchase for labor and

parts

• The warranty period for rental units begins

with the first rental or 45 days from date of

shipment to the rental firm, whichever comes

first.

What we will do:

• Pay any Authorized RCA Audio Service Center

the labor charges to repair your unit.

• Pay any Authorized RCA Audio Service Center

for the new or, at our option, refurbished

replacement parts required to repair your unit.

How you get service:

• Take your unit to any Authorized RCA Audio

Service Center. To identify your nearest

Authorized RCA Audio Service Center, ask your

dealer, look in the Yellow Pages, or call 1-800-

336-1900.

• Show the Authorized Service Center

Representative your evidence of purchase date

or first rental.

• Pick up your unit when repairs are completed.

• Proof of purchase in the form of a bill of sale

or receipted invoice which is evidence that the

product is within the warranty period must be

presented to obtain warranty service. For rental

firms, proof of first rental is also required.

What your warranty does not cover:

• Customer instruction. (Your Owner’s Manual

describes how to install, adjust, and operate

your unit. Any additional information should

be obtained from your dealer.)

• Installation and related adjustments.

• Signal reception problems not caused by your

unit.

• Damage from misuse or neglect.

• Cleaning of audio heads.

• Batteries.

• A unit that has been modified or

incorporated into other products or is used for

institutional or other commercial purposes.

• A unit purchased or serviced outside Canada.

• Acts of nature, such as but not limited to

lightning damage.

Product Registration:

• Please complete and mail the Product

Registration Card packed with your product. It

will make it easier to contact you should it ever

be necessary. The return of the card is not

required for warranty coverage.

Limitation of Warranty:

• THE WARRANTY STATED ABOVE IS THE

ONLY WARRANTY APPLICABLE TO THIS

PRODUCT. NO VERBAL OR WRITTEN

INFORMATION GIVEN BY THOMSON

MULTIMEDIA LTD., ITS AGENTS OR

EMPLOYEES SHALL CREATE A GUARANTY

OR IN ANY WAY INCREASE THE SCOPE OF

THIS WARRANTY.

• REPAIR OR REPLACEMENT AS PROVIDED

UNDER THIS WARRANTY IS THE EXCLUSIVE

REMEDY OF THE CONSUMER. THOMSON

MULTIMEDIA LTD. SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM THE USE OF THIS

PRODUCT. EXCEPT TO THE EXTENT

PROHIBITED BY APPLICABLE PROVINCIAL

LAW, ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE ON THIS PRODUCT IS

LIMITED TO THE APPLICABLE WARRANTY

PERIOD SET FORTH ABOVE.

How Provincial Laws relates to warranty:

• This warranty gives you specific legal rights

which are in addition to statutory warranties

that may vary from Province to Province.

If you purchased your unit outside Canada:

• This warranty does not apply. Contact your

dealer for warranty information.

Service calls which do not involve

defective materials or workmanship are

not covered by this warranty. Costs of

such service calls are the sole responsibility

of the purchaser.

Operating your Receiver

NOTE

1. If there is interference, move the

location of the antenna until the optimal

sound is heard. TV and other electronic

devices could be the cause of

interferences so try to position the

antenna away from them.

2. Weak signal can affect the "auto Search

function". Adjust the antenna for better

reception and for a more efficient

search.

NOTE

A Weak signal can affect the "Automatic

Preset Storing function" efficiency. Adjust

the antenna for the best reception, and a

more efficient search.

Advanced Sound Control

Sound Enhancement Systems

This receiver is equipped with several built-in

sound enhancement systems.

Dolby Digital

The Dolby Digital mode lets you enjoy full

digital surround from software processed in

the Dolby Digital format. Dolby Digital

provides better sound quality and more

powerful presence than conventional Dolby

Surround.

This unit is equipped with Dolby Digital 5.1-

channel so that you can enjoy enhanced full

digital surround sound. Being different from

Dolby Pro Logic in which only four channels (

Front Left, Front Right, Centre and Rear ) are

used, the new system provides stereo

separation of the rear speakers (Rear-Right,

Rear-Left ). These 5 channels, together with

the subwoofer channel for bass sounds

(counted as 0.1 channel ), constitute as 5.1-

Channel ( or 6 Channels ) Input for Dolby

Digital that brings you the most sophisticated

sound enjoyment.

Dolby Pro Logic II

The Pro Logic II mode uses the built-in circuit

to steer the Left, Center, Right and Surround

left and right channel audio signals and uses

all five speakers to play both stereo and Dolby

Pro Logic program source, such as TV and VCR.

Dolby Pro Logic II includes Dolby Pro Logic II

Movie, Dolby Pro Logic II Music and Dolby Pro

Logic Emulation.

You can use this mode with any stereo

program source (such as VCR/SAT) to enjoy

multi-channel sound experience.

Dolby 3 Stereo

The 3 Stereo mode will redirect the Surround

signals to the front left and right speakers

when only the front and

center speakers are used.

Stereo

The Stereo mode uses the two main channel

outputs from the front speakers. Use this mode

if you have connected the front speakers only.

DSP (Digital Sound Processor)

These digital sound effects resemble sounds in

a real environment such as (DISCO / STADIUM /

THEATER / JAZZ CLUB / ARENA). DSP

automatically converts analog audio signals to

digital ones which enables you to adjust the

sound without degrading the sound quality.

Different modes will give you different feels of

size and types of listening environment.

Night Mode

By using Dynamic Range Control technology,

you can enjoy enhanced Dolby Digital sound

quality at night without interrupting your

roommates or neighbors. Night Mode will

compress the difference between normal

voices and sounds such as explosions, while still

enjoying a Dolby Digital enable component

(DVD, SAT).

Night Mode can be activated by pressing the

NIGHT button on the remote control. DRC OFF

(Default) appears on the display. While DRC

OFF (Default) is still on the display, continue to

press the button to toggle and selectNIGHT

the desired night mode. There are three modes

(DRC OFF, SOFT, ON) for you to choose the

extents of compression.

Dynamic Bass Amplified System

(dBas)

With “Dynamic Bass Amplified System” (dBas),

the discrete amplifier is located in the receiver

so the subwoofer keeps the power needed to

reproduce powerful effects.

4 settings are available: SOFT, BALANCED,

STRONG and POWERFUL.

Press the SUBWOOFER button to toggle the

subwoofer (dBas) effects level according to

your needs.

Fine Setting of the Components

The receiver can be directly turned on by

pressing the DVD•6CH / SAT•CABLE / TV /

CD•TAPE / VCR / TUNER buttons on the

remote control, which also selects the best

surround sound mode. The default surround

modes for different components are listed in

the table below.

If you decide to change the surround mode,

you can press the SURROUND button

repeatedly to toggle among the different

surround mode choices and select the one you

want.

DOLBY PL II MUSIC => DOLBY PL EMULATION

=> 3 STEREO => ARENA => JAZZ CLUB =>

THEATER => STADIUM => DISCO => STEREO =>

DOLBY PL II MOVIE

The receiver will keep the last selection in

memory.

Input Signal Setting

The receiver defaults to the most convenient

settings for your easiest use (see table).

If your connection is different from the default

setting,

1. Select the source

2. Press the SETUP button to show setup

options.

3. Press the Left or Right adjustment

buttons until ANALOG is displayed.

4. Press the Up or Down arrow buttons

to select among optical/ coaxial/

analog to match your connection.

Your selection will be stored

automatically.

The selected source and input source will be

displayed on the display as long as they are

active, except for some temporary change of

display (e.g. adjusting volume).

Digital Input

Select this setting to play digital signals from a

DVD, CD, LD player, SAT or TV.

Analog Input

Select this setting to play analog signals from a

cassette deck, VCR or turntable.

Fine Setting of the Speakers

All the basic settings have already been pre-set

for the speakers included in the box.

Also, to make the surround sound more

effective and suit the acoustic conditions in

your listening room, you may need to delay the

signal coming from some of the speakers.

Channel delay compensates for center or

surround speakers that are closer to the

listening position than the front speakers. You

can make use of the button to adjustSETUP

the speakers’ relative loudness.

Testing Speaker Loudness

You can listen to the loudness of the individual

speakers.

1. Press and hold

LEVEL on the

remote control.

A short noise will

be heard in the

speakers one by

one. The speaker

having the noise at

that moment will

be shown in the display.

2. To adjust the volume level of the test

tone, turn the VOLUME knob or press

the or VOL Up DOWN buttons on the

remote control to adjust the master

volume (if necessary)

Press LEVEL again

and press the Up

or Down buttons

to adjust the

individual

channel noise

level.

Adjust Individual Speaker Volume

1. To adjust individual speaker volume level,

press the LEVEL key on the remote control.

2. Continue to press the LEVEL button on the

remote control to select the channel to be

adjusted, then press the Up or Down buttons

to adjust the level.

You can adjust the master volume level by

turning the VOLUME knob or press the VOL

UP DOWN or buttons on the remote control.

Advanced Setting

Factory defaulted Advance setting

indication from VFD

The receiver has defaulted the following

distances:

Front speakers (FRNT) 15 ft

Center speaker (CNTR) 15 ft

Rear speaker (SURR) 10 ft

Speaker Configurations

You can also change the setup of the speakers.

Use a subwoofer to enjoy optimum sound.

• Speaker distance: For optimum surround

experience measure the distance between the

speaker and your favorite listening position.

1. Press the SETUP

button to show

setup options.

2. Press the Left or

Right adjustment

buttons until the

speaker you

want to change

is displayed.

3. Press the Up or

Down arrow

buttons to

change the

speaker settings.

Your selection

will be stored

automatically.

4. Repeat step 2 and 3 to set up the next

speaker

5. When set up is done, wait for 5

seconds to automatically save your

settings or press any key to save your

selection and set up mode.

Displaying Program Formats

When a digital source starts playing,

the receiver automatically switches to

the proper surround mode and

provides setting information via the

speaker icons located on the right-hand side of

the display.

It is important to note, however, that not all

Dolby Digital sources are encoded with the full

complement of five channels plus LFE*. Speaker

icons show how many and which speaker you

have enabled (See “Fine Setting of the

Speakers”) and the letters inside the speaker

icons show which channel is present in the

source information. For example, the diagram

shown means you have all five speakers and

subwoofer enabled and the digital sources you

played have five channels plus LFE

complemented.

* LFE stands for Low Frequency Effect. The

indication “LFE” appears if the digital source

contains LFE information. In this case, the bass

signal will be delivered to the subwoofer,

offering more dynamic deep bass sound

effects. If the letter is flashing, the signal is

either too weak or just gone.

Front Left Speaker Front Right Speaker

Subwoofer

Center Speaker

Rear Right Speaker

Rear Left Speaker

Listening

Zone

Front Left Speaker Front Right SpeakerCenter Speaker

Listening

Zone

NOTE

Night mode is available only with Dolby

Digital playback.

Advanced Sound Control

Source/ If Digital Input (optical

Input or coaxial) is selected

DVD Dolby Digital

SAT Dolby Digital

VCR N/A

TV Dolby Digital

CD STEREO

TAPE N/A

TUNER N/A

Source / If Analog Input is

Input selected

DVD PRO LOGIC

SAT PRO LOGIC

VCR PRO LOGIC

TV PRO LOGIC

CD STEREO

TAPE STEREO

TUNER STEREO

NOTE

If linear PCM source (CD), format will be

Dolby Prologic even with Digital Input.

DEFAULT INPUT

(as seen on display)

Analog (SAT/ ANL)

Analog (DVD/ ANL)

Analog (CD/ ANL)

Analog (VCR/ ANL)

Built-in Tuner

Analog (TAPE/ ANL)

Analog (TV / ANL)

SOURCE

SAT

DVD

VCR

FM/AM

TAPE

AVAILABLE INPUT

Analog / Optical / Coaxial

Analog / - / -

Analog / Optical / -

SOURCE

SAT

DVD

VCR

TAPE

NOTE

Digital input is only available for DVD, SAT,

CD and TV

R/SL/S

Rch

Cch

Lch

Front

Left

Rear

Right

Rear

Left

Front

Right

Center

Center Speaker selection (CTR) YES / NO

Surround Speaker selection (SURR) YES / NO

Front Speaker distance (FRNT) 3-30 ft

Centre Speaker distance (CNTR) 0-30 ft

Rear Speaker distance (SURR) 0-30 ft

NOTE

By default, the Center and Surround

Speakers are set to YES. If you decide not

to use them, set the ones you do not

intend to use to NO so the sound

performance is not affected.

LS RS

LFE

RCL

Troubleshooting Tips

Care and Maintenance

Limited Warranty (U.S.)

Limited Warranty (Canada)

RT2390 EN sheet final 12/28/04 9:42 AM Page 2

Product specificaties

Merk:	RCA
Categorie:	Home cinema set
Model:	RT2390

Heb je hulp nodig?

Als je hulp nodig hebt met RCA RT2390 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Home cinema set RCA

RCA RTD317W Handleiding

29 April 2023

RCA RT2390 Handleiding

11 Februari 2023

RCA RTD205 Handleiding

2 Februari 2023

RCA RTD300 Handleiding

30 Oktober 2022

Handleiding Home cinema set

Nieuwste handleidingen voor Home cinema set

Boston Acoustics TVee One Handleiding

1 December 2024

Samsung HT-Z121T Handleiding

25 November 2024

Philips Immersive Sound HTS5710H Handleiding

23 November 2024

LG DA-3620 Handleiding

22 November 2024

LG F-DV25 Handleiding

22 November 2024

LG LH-T360SE Handleiding

22 November 2024

LG LH-T6740 Handleiding

22 November 2024

LG LH-T760IA Handleiding

22 November 2024

Sony WS-FV10D Handleiding

22 November 2024

Sony WS-FV10DSC Handleiding

22 November 2024