RCA RCR4373 Handleiding

RCA Controller RCR4373

Lees hieronder de 📖 handleiding in het Nederlandse voor RCA RCR4373 (6 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

Four-Component

Universal Remote

Congratulations on your purchase of this four-component

universal remote. This universal remote controls up to four

electronic components and makes juggling remote controls

a thing of the past. Your remote is guaranteed to work with

all brands of components. This remote is unusually versatile

because it has a DVR•AUX key that you can program to control

any video component. The four-component universal remote is

easy to use, easy to program and gives you control at the touch

of your ﬁngertips.

SAVE THIS MANUAL AND THE CODE LISTS!

Remote controls can sometimes lose their programming when you

change the batteries. Make sure you keep the manual and code lists in

a safe place so that you can reprogram the remote if you need to.

Tip: The four-component universal remote is already programmed

to operate most RCA, GE and PROSCAN branded TVs, VCRs,

DVD players and satellite receivers. Just press the corresponding

key—DVD•VCR for a DVD player, TV for a television, SAT•CBL

for a satellite receiver, DVR•AUX for a DVR.

Component

keys ( , TV

SAT•CBL,

DVD•VCR,

DVR•AUX)

Dedicated

MENU and

GUIDE

keys let

you access

advanced

component

functions

Transport

keys,

including

SKIP and

SLOW, give

you better

DVD/DVR

control

CH and

VOL keys

have dual

functions:

they can

act as

navigation

keys in

systems

as well as

channel

and volume

controllers

outside the

menus

INFO key

displays

information

for the

component

you’re

controlling

Actual

model may

vary from

picture

shown

Battery Installation and Information

Your universal remote requires two AAA Alkaline batteries

(batteries may or may not be included, depending on model).

To install the batteries:

1. Remove the battery compartment

cover.

2. Insert the batteries, matching the

batteries to the (+) and (–) marks

inside the battery compartment.

3. Push the battery cover back into place.

Note: If you are replacing batteries, try not to press any buttons after

you’ve taken the old batteries out. Pressing buttons while replacing

batteries causes the remote to lose the devices you’ve programmed. You

will need to program the remote again.

Battery Precautions:

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-

cadmium) batteries.

• Always remove old, weak or worn-out batteries promptly and recycle or

dispose of them in accordance with Local and National Regulations.

Battery Saver

Your universal remote control saves battery power by

automatically turning off if any key is pressed for more than

60 seconds. This saves your battery life should your remote

get stuck in a place where the keys remain depressed, such as

between sofa cushions.

The INPUT and — (dash) key has three functions:

(1) it toggles through all the video sources

connected to your TV; (2) when the remote is in VCR

mode, this button toggles between VCR and the

TV input; (3) when you’re entering digital channel

numbers directly, this button lets you separate the

main channel number from the subchannel number

RCR4273 / RCR4373

Universal Remote Control

Owner’s Manual

Manual del Propietario (parte posterior)

Programming Your Remote

Your universal remote can operate a variety of brands of

components. In order for your universal remote to control your

components, you need to program the remote with the codes

that match the components (See Code Lists enclosed or go to

rca.com/codeﬁnder). These codes enable the remote to

communicate with your components. Each brand and each

component has its own “language,” and, by programming the

correct codes into your remote, you tell the remote to “speak the

same language” as your components.

Care and Maintenance

• Keep the remote dry. If it gets wet, wipe it dry immediately.

• Use and store the remote only in normal temperature

environments.

• Handle the remote gently and carefully. Don’t drop it.

• Keep the remote away from dust and dirt.

• Wipe the remote with a damp cloth occasionally to keep it

looking new.

• Modifying or tampering with the remote’s internal components

can cause malfunction and invalidate its warranty.

There are four methods you can use to program your remote

control to operate your components:

• Brand Code Search and Entry

• Direct Code Entry

• Manual Code Search and Entry

• Auto Code Search and Entry

Most components can be programmed in one of these four

ways. Try them in the order listed.

In order to control combo TV/VCR or TV/DVD units, you

must program both the TV key and the DVD•VCR key. Once

programmed successfully, the TV key controls the TV functions

on your unit, and the DVD•VCR key controls the DVD or

VCR functions. There is a speciﬁc section in the Code Lists

for combo units. The codes in this section should be tried ﬁrst,

using Direct Code Entry on the TV and DVD•VCR keys. If this

is unsuccessful, follow the normal programming methods for

both the TV and the DVD•VCR keys.

DVD•VCR Key

Important: The DVD•VCR key defaults to program a DVD

player. If you want the DVD•VCR key to control a VCR, you

must preprogram the DVD•VCR key. See the section entitled

“Programming the DVD•VCR Key To Control a VCR” on page 3.

DVR•AUX Key

Important: The DVR•AUX key defaults to program a DVR.

If you want the DVR•AUX key to control a component

other than a DVR (an additional TV or DVD, for example),

you must preprogram the DVR•AUX key. See the section

entitled “Programming the DVR•AUX Key To Control Other

Components” on page 4.

Brand Code Search and Entry

If your brand is listed in the Brand Code List (See Code Lists

enclosed), you may be able to program your universal remote

by searching through only the Code Lists for that speciﬁc

manufacturer. Brand Code Search and Entry can be the

quickest method to program your remote, if your component is

one of those brands listed.

If your brand is not listed in the Brand Code List, use one of

the other programming methods that follow.

Follow these instructions to program your remote using the

Brand Code Search and Entry method.

TIP: To exit without saving at any point in the Brand

Code Search, press and release the CLEAR key.

1. Manually turn on the component you want the remote to

control (TV, VCR, DVD, DVR, satellite receiver, or cable

box).

2. Locate the Brand Codes in the Code Lists and keep it handy.

Note: If you press an invalid key during the Brand Code Search,

the remote does not respond. If you do not press a valid Brand Code

Search key (TV, SAT•CBL, DVD•VCR, DVR•AUX, POWER,

CLEAR, and number keys 0-9), the search times out after two

minutes. When the search times out, the LED blinks four times and

turns off. The last programmed code under that component key is

retained.

3. Press and hold the component

key (TV, SAT•CBL, DVD•VCR,

DVR•AUX) you wish to program.

The LED turns on and remains

on. Keep holding down the

component key.

LED

4. While holding the component key down, press and hold the

POWER key. The LED turns off. After holding both keys

down for three seconds, the LED turns back on.

5. Release both keys. The LED remains on.

6. Refer to the Brand Codes in the enclosed Code Lists. Use

the number keys to enter the number for your brand. The

LED blinks once.

TIP: Throughout the programming of each key, be sure to keep the

remote pointed at the IR sensor of the component you are currently

programming the remote to control.

7. Press and release the POWER key repeatedly until your

component turns off. Each time you press the POWER key,

the LED blinks and the next code is sent. The Brand Code

Search begins with the ﬁrst code in the chosen brand list for

that component and cycles through all the codes for that

brand.

If your component turns off, you have found the correct

code. If the remote cycles through and the LED blinks four

times and turns off, all codes in the chosen brand lists have

been searched and another programming method should be

tried. The Brand Code Search mode is exited.

8. Once you have found the correct code, you must

save that code by pressing and releasing the STOP

key. The LED turns off.

IM PORTANT: You must press the STOP key to save the code or the

correct code will not be stored!

Testing the Code for Maximum

Functionality

Different remote control codes can provide different levels

of functionality. To conﬁrm that the component key is

programmed with the correct code for maximum functionality,

follow the steps below.

1. Attempt to control a variety of the component’s functions

with the remote. If some features of your components do

not work, go to step 2 to try a different code.

2. Repeat the Brand Code Search and Entry Method from step 1.

When the component turns off for the ﬁrst time, do not press

the STOP key, which would store the code. Instead, with the

unit now off, continue to press the POWER key repeatedly

until the unit turns back on.

3. Once the unit turns back on, you have found another code

that operates the component. Press the STOP key.

4. Test the key’s functionality again by attempting to control

a variety of the component’s functions. If the code that

has been stored controls the majority of the component’s

functions, programming is complete. If the code stored does

not give maximum functionality, try another code.

5. Repeat the Brand Code Search and Entry Method from

step 1. Each time a code turns the component on or off, you

have found a code that operates the component and needs to

be tested for maximum functionality. Continue through the

code lists, cycling through the codes you have already tried,

until you ﬁnd one that offers maximum functionality.

The RCA Easy Interactive Code Finder

The online interactive code ﬁnder at www.rca.com/codeﬁnder makes it

easier to ﬁnd exactly the right codes for your components. The code ﬁnder

takes you right to the best code(s) for your component—no need to go

through long code lists!

Notes:

• To program the DVD•VCR key to control a VCR, see page 3.

• To program the DVR•AUX key to control a component other than

a DVR, see page 4.

Programming the DVD•VCR Key to Control a VCR

The DVD•VCR key defaults to control a DVD player. If you want the DVD•VCR key to control a VCR, you must preprogram

the DVD•VCR key.

1. Press and hold the DVD•VCR key. The LED turns on. Keep holding down the DVD•VCR key.

2. While holding down the DVD•VCR key, press and release the number 2 key on the keypad. The LED turns off.

3. Release the DVD•VCR key. The LED blinks four times and then turns off. The DVD•VCR key is now “set” to control a VCR.

4. Next, program the DVD•VCR key to control the brand of VCR you have. Remember to consult the VCR code list.

Direct Code Entry

To use the direct code entry method to program your universal

remote to control your components, follow the steps below.

1. Manually turn on the component you want the remote to

control (TV, VCR, DVD, DVR, satellite receiver, or cable box).

2. Locate the enclosed Code Lists. Find the list for the

component you wish to program. Find your component’s

brand. You will see a listing of four-digit codes for each

brand. If your brand isn’t listed, use one of the Code Search

methods to program the remote control. (Refer to pages 3–8

for Manual and Auto Code Search methods.)

Note: You can also use the online code ﬁnder at

www.rca.com/codeﬁnder to ﬁnd the best code for your component.

Code Entry procedure, the LED blinks four times, and

the process is exited. The last programmed code under the

component key is retained.

Notes:

• To program the DVD•VCR key to control a VCR, see below.

• To program the DVR•AUX key to control a component other than

a DVR, see page 4.

4. While holding down the component key, consult the

Code Lists for the four-digit code that corresponds to your

component’s brand and use the number keys (0-9) to enter

it. After you press the ﬁrst number, the LED turns off. After

the fourth number is entered, the LED turns on.

TIP: Throughout the programming of each key, be sure to keep the

remote pointed at the IR sensor of the component you are currently

programming the remote to control.

5. Release the component key. If the LED turns off, you

have entered a valid code and have followed the correct

procedure for Direct Code Entry. Proceed to the next step.

If the LED blinks four times, you have either entered a code

number that is not in the code lists or missed a step in the

code entry procedure. Repeat the Direct Code Entry process

from step 3 and try the next code listed.

6. To conﬁrm that the component key is programmed with the

correct code for maximum functionality, test the component.

Attempt to control a variety of the component’s functions

with the remote. If some features of your components do not

work, try programming the remote with a different code in the

list until you ﬁnd the code that allows the remote to control

the majority of your component’s functions. Different codes

can provide different levels of functionality.

I M PORTA NT: Remember to enter the code for future reference in

the box provided in the Code Retrieval section of this manual. (See

page 5.)

3. Press and hold the component

key (TV, SAT•CBL, DVD•VCR,

DVR•AUX) you wish to program.

The LED turns on and remains on.

Keep holding down the component

key. If you release the component

key any time during the Direct

LED

Manual Code Search and Entry

If your component’s brand isn’t listed in the Code Lists, or if

you have tried all of the codes for your brand and the remote

does not operate your component, try one of the Code Search

methods below—Manual Code Search or Auto Code Search.

Both Code Search methods cycle through all of the codes in

the Code Lists in the event that your component’s code is

listed under another brand.

Note: The Manual Code Search method may take a long time

because the remote searches through all of the codes in its memory for

the code that operates your component. Therefore, if your brand is

listed in the Brand Codes or the Code Lists, ﬁrst try the Brand Code

Search or the Direct Code Entry method described on the left.

1. Manually turn on the component you want the remote to

control (TV, VCR, DVD, DVR, satellite receiver, or cable box).

Notes:

• To program the DVD•VCR key to control a VCR, see page 3.

• To program the DVR•AUX key to control a component other than

a DVR, see page 4.

TIP: To exit without saving at any point in the Manual

Code Search, press and release the CLEAR key.

2. Press and hold the component

key (TV, SAT•CBL, DVD•VCR,

DVR•AUX) you wish to program.

The LED turns on and remains on.

Keep holding down the component

key.

3. While holding the component key down, press and hold the

POWER key. The LED turns off. After holding down both

keys for three seconds, the LED turns back on.

4. Release both keys. The LED remains on.

Note: If you press an invalid key during Manual Code Search, the

remote does not respond and the search times out after two minutes.

When the search times out, the LED blinks four times and turns off.

The last programmed code under that component key is retained.

TIP: Throughout the programming of each key, be sure to keep the

remote pointed at the IR sensor of the component you are currently

programming the remote to control.

5. Press and release the POWER key repeatedly until your

component turns off. Each time you press the POWER key,

the LED blinks, and the next code in the list is sent. This

process continues until all of the codes in the Code Lists

have been tried. If your component turns off, you have

found the correct code. (If it cycles through and the LED

blinks four times and turns off, all codes have been searched.

The Manual Code Search method is exited.)

TIP: Because there are so many codes, you may have to press the

POWER key many times—possibly hundreds of times.

6. Once you have found the correct code, you must

save the new code by pressing and releasing the

STOP key. The LED turns off. You must press the

STOP key to save the code or the correct code will

not be stored! When you press the STOP key, the

code is stored.

7. Be sure to retrieve the code your remote programmed by

ﬁnishing the Code Retrieval process found on page 5.

LED

Product specificaties

Merk:	RCA
Categorie:	Controller
Model:	RCR4373

Heb je hulp nodig?

Als je hulp nodig hebt met RCA RCR4373 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Controller RCA

RCA RCR4358R Handleiding

16 Mei 2023

RCA RCR313BZ Handleiding

28 April 2023

RCA RCRPS02GR Handleiding

15 April 2023

RCA RCRN06GBE Handleiding

14 April 2023

RCA RCR412BN Handleiding

5 April 2023

RCA RCR311BN Handleiding

1 April 2023

RCA RCU800MS Handleiding

18 Maart 2023

RCA RCR311BIN Handleiding

11 Maart 2023

RCA RCR311SN Handleiding

23 Februari 2023

RCA RCR4373 Handleiding

23 Februari 2023

Handleiding Controller

Nieuwste handleidingen voor Controller

Smart-AVI EZWALL-PLUS 2X2 Handleiding

20 November 2024

Gamesir F4 Falcon Handleiding

19 November 2024

HQ Power HQDB10002 Handleiding

18 November 2024

Ltech CHLSC43 Handleiding

17 November 2024

IVT DR-2000 Handleiding

17 November 2024

Speed-Link RAIT SL-650110-BK Handleiding

16 November 2024

Genesis MANGAN 400 Handleiding

15 November 2024

Steelseries Stratus Duo Handleiding

14 November 2024

Thrustmaster TM Flying Clamp Handleiding

14 November 2024

MOZA Hand Brake Handleiding

14 November 2024