Rangemaster UB40 Handleiding

Rangemaster Spoelbak UB40

Lees hieronder de 📖 handleiding in het Nederlandse voor Rangemaster UB40 (8 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Instructions for Atlantic single, Atlantic double, Quadbowl, Kube

STAINLESS STEEL

UNDERMOUNT BOWLS

Installation Instructions

Aftercare Information

Installer

Please leave this leaet with the user, as it contains valuable

after care advice.

Notes

 Undermount sinks should only be xed to granite

worktops by a specialist installer.

 Please beware of sharp metal edges prior to and

during installation.

 During installation, take care to protect the bowl

from scus and scratches.

 Avoid straining and overtightening of all plumbing

xtures connected to the bowl.

 We recommend that the worktop opening is sealed

using waterproof sealant or a similar material.

Installation

Preparing the Worktop

1. Decide on the position that your bowl (or bowls) is to be

tted. Check that the bowl will not foul on the cabinet

below.

2. Place the sink upside down on the worktop. Position the

sink on the worktop as required. Make sure the cabinet

framework will clear all parts of the bowl. Using a soft,

sharp pencil draw around the bowl as accurately as

possible. Remove the bowl.

Alternatively, you can use a bowl template. For details

go to www.rangemaster.co.uk.

3. Referring to the templates as shown in this booklet,

draw another line – as indicate by ‘A’ (Fig.1) inside the

sink top outline – this is the cutting line for the opening.

4. Drill as large a hole as possible inside the cutting line.

Using a padsaw, jigsaw or similar, cut out the opening

up to the cutting line.

5. On the underside of the worktop, mark the positions for

the threaded inserts – see the templates in this booklet

for the correct dimensions or go to www.rangemaster.

co.uk for template details.

6. Drill the 10 mm diameter holes for the threaded (Fig.1)

inserts (refer to the worksurface supplier for drilling

advice and the drill bit diameter required).

7. Glue the threaded xing inserts into the drilled holes.

Applying the Sealant

Apply silicone sealant (not supplied) to the bowl rim (Fig.2).

14 mm

10 mm

Fig.1

Due to our policy of continual improvement, we reserve the right to change specications without prior notice.

Undermount bowl

Fig.2

Dimension A: 33mm, 27mm or 22mm depending on the bowl –

see the templates in this booklet for this dimension.

INSTALLATION

Fig.4

Fig.3

A – Threaded insert, B – Fixing clamp, C – Bowl, D – Seal

Fitting the Bowl

Position the bowl to the worktop. Using the xing clamps and

screws (Fig.3), secure the bowl to the worktop (Fig.4).

 DO NOT tighten fully at rst attempt.

 DO NOT overtighten the clamps.

Remove any surplus sealing material or wipe away any excess

sealant.

Note: Some bowls may require additional support (this

should be supplied and tted by your installer).

Fitting the Square Overflow Pipework

(Kube & Quadbowl models)

The overow pipework for the square style underbowls may

require modifying to t.

Fig.5 shows the suggested areas of the overow pipework

that may need to be cut. Measure the pipework, and cut the

areas show as required. Fit together as normal.

To ensure a watertight seal, apply silicon sealant onto the

sink-side face of the rubber seal before tting it to the sink

(Fig.6).

Rubber seal

Sink-side face

Silicon sealant

Fig.5

Fig.6

Product specificaties

Merk:	Rangemaster
Categorie:	Spoelbak
Model:	UB40
Kleur van het product:	Roestvrijstaal
Breedte:	460 mm
Diepte:	440 mm
Soort wastafel:	Onderbouwspoelbak
Vorm gootsteen:	Rechthoekig
Materiaal gootsteen:	Roestvrijstaal
Aantal gootstenen:	1 kommen
Vorm eerste spoelbak:	Rechthoekig
Eerste kom dimensies (WxL):	420 x 400 mm
Eerste kom diepte:	190 mm
Kraangat:	Nee
Aanrecht:	Nee
Kraan inclusief:	Nee