Rangemaster LU9852 Handleiding
Rangemaster
Spoelbak
LU9852
Lees hieronder de ๐ handleiding in het Nederlandse voor Rangemaster LU9852 (4 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
Instructions for Cubix, Cubix Gemini & Lunar
COMPOSITE INSET SINKS
๏ฎWITH FIXED POSITION CLIPS๏ฏ
Installation Instructions
&
Aftercare Information
INSTALLATION
Installer
Please leave this lea๎et with the user, as it contains valuable
after care advice.
Notes
๎๎ฎ During installation, take care to protect the sink
from scu๎s and scratches.
๎๎ฎ Avoid straining and overtightening of all plumbing
๎xtures connected to the sink.
๎๎ฎ Carefully check that the moulding and edges of the
sink are dead level so that water will ๎ow o๎ the
drainer.
๎๎ฎ We recommend that the worktop opening is sealed
using waterproof sealant, paint or a similar material.
๎๎ฎ The clamping brackets are suitable for worktops of
between 28โ40 mm thickness. If your worktop is a
di๎erent size then it may require packing under the
clips or rebating.
Preparing the Worktop
Marking out the opening
We recommend that you ๎t the inset sink to the worktop
before permanently ๎xing the worktop to the cabinet.
1. Place the sink upside down on the worktop. Position
the sink on the worktop as required. Make sure the
cabinet framework will clear all parts of the sink. Using a
soft, sharp pencil draw around the sink as accurately as
possible (Fig.1). Remove the sink.
Alternatively, you can use a sink template. For details go
to www.rangemaster.co.uk.
2. Draw another line 10๎mm inside the sink top outline โ
this is the cutting line for the opening (Fig.2).
3. Drill as large a hole as possible inside the cutting line.
Using a padsaw, jigsaw or similar, cut out the opening
up to the cutting line.
Preparing the sink
Drilling a taphole
๎๎ฎ Before drilling please read safety instructions
supplied with hole saw.
๎๎ฎ The front face must be fully supported to prevent
cracking when drilling or cutting.
๎๎ฎ WARNING!
Composite sink products include a silica ๎ller. Any
machining operation will produce ๎ne particles of
dust. Drilling or cutting be carried out in a MUST
well-ventilated area.
Worktop
Final position
of sink
Cutting line for opening
10 mm
Fig.1
Fig.2
Due to our policy of continual improvement, we reserve the right to change speci๎cations without prior notice.
Fig.3
Fig.4
If a taphole is required, but has not been supplied in the sink,
proceed as follows:
1. Decide whether the bowl is to be left or right handed
when the sink is ๎tted. You will require a 35 mm hole
saw (supplied with selected products).
2. On the reverse side of the sink you will ๎nd a location
point for tap cut-out (Fig.3).
3. Using the 35 mm hole saw, carefully cut out the tap
hole.
Fitting the clips
There are two methods of ๎tting the clips:
โข๎ Screw down ๎xing or,
โข๎ Pin ๎xing
Screw down ๎xing
1. Using the screws supplied, ๎t the mounting clips to the
sink (Fig.4).
2. Hinge the clips away from the sink edge.
Pin ๎xing
1. Position the clips over the pins molded in the sink. Pull
and twist the clip towards the edge of the sink (Fig.5)
until it snaps into place.
2. If a clip is tight then, using a ๎at screwdriver, tap on the
base until it snaps into place (Fig.6).
3. Hinge the clips away from the sink edge.
At this stage, test ๎t the sink in the worktop opening. You may
need to enlarge the opening around the clips.
Fit the tap and waste ๎ttngs to the sink using the instructions
supplied with them.
Fitting the seal or sealant
There are 2 methods of sealing your sink to the worktop:
โข๎ Foam seal or,
โข๎ Silicon sealant
Foam seal
Peel o๎ the backing strip and stick the seal to the recess in
the sink (Fig.7). Make sure that a neat butt joint is achieved
where the ends of the seal meet.
Silicon sealant
Apply silicone sealant (not supplied) to the underside of the
sink rim (Fig.8).
Fitting the sink
1. Turn the sink upside down and lay the worktop over
the sink. Swing each clip into place (Fig.9) โ this is the
most e๎ective method, although if the worktop has
been ๎tted to the cabinet the sink can be placed in the
opening and ๎xed in position from underneath.
2. Centre the sink. Tighten the ๎xing screws.
๎๎ฎ DO NOT tighten fully at ๎rst attempt.
Remove any surplus sealing material or wipe away any excess
sealant.
Tap on clip base with
a ๎at screwdriver
Fig.5
Fig.6
Fig.7
ArtNo.512-0001 - Gemini applying sealant
Fig.8
SinkWorktop
1 2 3
Fig.9
Product specificaties
Merk: | Rangemaster |
Categorie: | Spoelbak |
Model: | LU9852 |
Kleur van het product: | Zilver |
Breedte: | 985 mm |
Diepte: | 508 mm |
Gewicht verpakking: | 13500 g |
Breedte verpakking: | 6500 mm |
Diepte verpakking: | 2550 mm |
Hoogte verpakking: | 1100 mm |
Installatie compartiment breedte: | 964 mm |
Installatie compartiment diepte: | 487 mm |
Soort wastafel: | Inbouwspoelbak |
Vorm gootsteen: | Rechthoekig |
Materiaal gootsteen: | Metallix |
Aantal gootstenen: | 2 kommen |
Eerste kom dimensies (WxL): | 345 x 430 mm |
Eerste kom diepte: | 180 mm |
Tweede kom dimensies (WxL): | 160 x 430 mm |
Tweede kom diepte: | 110 mm |
Kraangat: | Ja |
Tap-gat grootte: | 35 mm |
Aantal kraangaten: | 1 |
Aanrecht: | Ja |
Kraan inclusief: | Nee |
Heb je hulp nodig?
Als je hulp nodig hebt met Rangemaster LU9852 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Spoelbak Rangemaster
26 Mei 2023
10 Mei 2023
8 April 2023
8 April 2023
2 April 2023
17 Maart 2023
7 Maart 2023
1 Maart 2023
28 Februari 2023
25 Februari 2023
Handleiding Spoelbak
- Spoelbak Bartscher
- Spoelbak Blaupunkt
- Spoelbak Franke
- Spoelbak Hendi
- Spoelbak Hotpoint-Ariston
- Spoelbak Leisure
- Spoelbak Saro
- Spoelbak Smeg
- Spoelbak Teka
- Spoelbak Concept
- Spoelbak Blanco
- Spoelbak Caple
- Spoelbak CDA
- Spoelbak Kernau
- Spoelbak Artusi
- Spoelbak Foster
- Spoelbak Nodor
- Spoelbak Elkay
- Spoelbak Gustavsberg
- Spoelbak Schock
- Spoelbak Roca
- Spoelbak Advance Tabco
- Spoelbak Eagle Group
- Spoelbak Sani-Lav
- Spoelbak Fulgor Milano
- Spoelbak Laveo
- Spoelbak Deante
- Spoelbak Tot Mate
- Spoelbak Atosa
- Spoelbak Kuchinox
- Spoelbak Oliveri
- Spoelbak Shaws
- Spoelbak Seima
Nieuwste handleidingen voor Spoelbak
17 December 2024
17 December 2024
16 December 2024
16 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024
6 December 2024