Rangemaster OL9851 Handleiding

Rangemaster Spoelbak OL9851

Lees hieronder de 📖 handleiding in het Nederlandse voor Rangemaster OL9851 (4 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Instructions for Manhatton, Keyhole, Chicago, Oakland, Glendale, Baltimore & Arlington

STAINLESS STEEL INSET SINKS

WITH FIXED POSITION CLIPS

Installation Instructions

Aftercare Information

Installer

Please leave this leaet with the user, as it contains valuable

after care advice.

Notes

 Please take care of sharp metal edges before and

during installation.

 During installation, take care to protect the sink

from scus and scratches.

 Avoid straining and overtightening of all plumbing

xtures connected to the sink.

 Carefully check that the moulding and edges of the

sink are dead level so that water will ow o the

drainer.

 We recommend that the worktop opening is sealed

using waterproof sealant, paint or a similar material.

 The clamping brackets are suitable for worktops of

between 28–40 mm thickness. If your worktop is a

dierent size then it may require packing under the

clips or rebating.

Installation

Marking Out the Opening

1. We recommend that you t the inset sink to the

worktop before permanently xing the worktop to the

cabinet.

2. Place the sink upside down on the worktop. Position

the sink on the worktop as required. Make sure the

cabinet framework will clear all parts of the sink. Using a

soft, sharp pencil draw around the sink as accurately as

possible (Fig.1). Remove the sink.

Alternatively, you can use a sink template. For details go

to www.rangemaster.co.uk.

3. Draw another line 10 mm inside the sink top outline –

this is the cutting line for the opening (Fig.2).

4. Drill as large a hole as possible inside the cutting line.

Using a padsaw, jigsaw or similar, cut out the opening

up to the cutting line.

Fitting the Sink

1. Open the hinge on the clip.

2. Turn the sink upside down and lay the worktop over

the sink. Swing each clip into place (Fig.3) – this is the

most eective method, although if the worktop has

been tted to the cabinet the sink can be placed in the

opening and xed in position from underneath.

3. Centre the sink. Tighten the xing screws in the

sequence shown in Table 1.

 DO NOT tighten fully at rst attempt.

 DO NOT overtighten the clips as this may distort the

sink rim.

Remove any surplus sealing material (Fig.4).

Worktop

Final position

of sink

Cutting line for opening

10 mm

Fig.1

Fig.2

Due to our policy of continual improvement, we reserve the right to change specications without prior notice.

1 2 3

SinkWorktop

Worktop

Trim with a sharp knife

Sealing tape

Fig.3

Fig.4

INSTALLATION

Fitting the Arlington Overflow

Pipework

The overow pipework for the Arlington sink will require

modifying to t. Cut the parts as shown (Fig.5). Fit together

as normal.

To ensure a watertight seal, apply silicon sealant onto the

sink-side face of the rubber seal before tting it to the sink

(Fig.6).

910

9 10

8 clips

9 clips (keyhole)

10 clips

Table 1 Clip positions and recommended tightening sequence

All dimensions in mm

30 mm

10 mm

55 mm

Rubber seal

Sink-side face

Silicon sealant

Fig.5

Fig.6

Product specificaties

Merk:	Rangemaster
Categorie:	Spoelbak
Model:	OL9851
Kleur van het product:	Roestvrijstaal
Gewicht:	6500 g
Breedte:	985 mm
Diepte:	508 mm
Gewicht verpakking:	8600 g
Breedte verpakking:	650 mm
Diepte verpakking:	265 mm
Hoogte verpakking:	1130 mm
Installatie compartiment breedte:	965 mm
Installatie compartiment diepte:	488 mm
Soort wastafel:	Inbouwspoelbak
Vorm gootsteen:	Rechthoekig
Materiaal gootsteen:	Roestvrijstaal
Aantal gootstenen:	1 kommen
Vorm eerste spoelbak:	Rechthoekig
Eerste kom dimensies (WxL):	450 x 420 mm
Eerste kom diepte:	190 mm
Kraangat:	Ja
Tap-gat grootte:	35 mm
Aantal kraangaten:	1
Aanrecht:	Ja
Kraan inclusief:	Nee
Plaats aanrecht:	Rechts