QSC QIO-S4 Handleiding

QSC Niet gecategoriseerd QIO-S4

Lees hieronder de 📖 handleiding in het Nederlandse voor QSC QIO-S4 (13 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/13
™
Hardware User Manual
Q-SYS™ QIO Endpoints
QIO-ML4i Network Audio I/O Expander for Q-SYS
QIO-L4o Network Audio I/O Expander for Q-SYS
QIO-ML2x2 Network Audio I/O Expander for Q-SYS
QIO-GP8x8 Network Control I/O Expander for Q-SYS
®
TD-001667-01-A
*TD-001667-01*
2
EXPLANATION OF TERMS AND SYMBOLS
The term “WARNING” indicates instructions regarding personal safety. Failure to follow them may result in bodily injury or death.
The term “ ” indicates instructions regarding possible damage to physical equipment. Failure to follow them may result in CAUTION
equipment damage to equipment that may not be covered under the warranty.
The term “IMPORTANT” indicates instructions or information that are vital to the successful completion of theprocedure.
The term “ ” indicates additional useful information.NOTE
The lightning flash with arrowhead symbol in a triangle alerts the user to the presence of uninsulated dangerous voltage within the
product’s enclosure that may constitute a risk of electric shock to humans.
The exclamation point within a triangle alerts the user to important safety, operating, and maintenance instructions in this manual.
IMPORTANT SAFETY INSTRUCTIONS
WARNING!: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
• Elevated Operating Ambient – If installed in a closed or multi-unit rack assembly, the ambient operating temperature
of the rack environment may be greater than room ambient. Consideration should be given to ensure that the maximum
operating temperature range (0°C to 50°C (32°F to 122°F ) is not exceeded. However, if installing a GP8x8 in a multi-unit
rack assembly with units on all sides, the maximum operating temperature should not exceed 40°C when devices are placed
above or below.
• – Installation of the equipment in a rack should be such that the amount of air flow required for safe Reduced Air Flow
operation of the equipment is not compromised.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Do not submerge the apparatus in water or liquids.
7. Do not use any aerosol spray, cleaner, disinfectant or fumigant on, near or into theapparatus.
8. Clean only with a dry cloth.
9. Do not block any ventilation opening. Install in accordance with the manufacturer’sinstructions.
10. Keep all ventilation openings free of dust or other matter.
11. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
12. Do not unplug the unit by pulling on the cord, use the plug.
13. Only use attachments/accessories specified by the manufacturer.
14. Unplug this apparatus during lightning storms or when unused for long periods oftime.
15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
16. Adhere to all applicable, local codes.
17. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.
3
Maintenance and Repair
WARNING: Advanced technology, e.g., the use of modern materials and powerful electronics, requires specially adapted
maintenance and repair methods. To avoid a danger of subsequent damage to the apparatus, injuries to persons and/or the creation of
additional safety hazards, all maintenance or repair work on the apparatus should be performed only by a QSC authorized service station
or an authorized QSC International Distributor. QSC is not responsible for any injury, harm or related damages arising from any failure of
the customer, owner or user of the apparatus to facilitate those repairs.
IMPORTANT! PoE Power Input - IEEE 802.3af Type 1 PSE required on LAN (POE) or 24 VDC power supply required.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
Environmental
• Expected Product Life Cycle: 10 years
• Storage Temperature Range: -20°C to +70°C
• Relative Humidity: 5 to 85% RH, non-condensing
RoHS Statement
The Q-SYS QIO Endpoints are in compliance with European Directive 2015/863/EU – Restriction of Hazardous Substances (RoHS).
The Q-SYS QIO Endpoints are in compliance with “China RoHS” directives per GB/T24672. The following chart is provided for product
use in China and its territories:
QSC Q-SYS QIO Endpoints
部件名称
(Part Name)
有害物质
(Hazardous Substances)
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(vi))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
电路板组件
(PCB Assemblies)
X O O O O O
机壳装配件
(Chassis
Assemblies)
X O O O O O
本表格依据 SJ/T 11364 的规定编制。
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。
（目前由于技术或经济的原因暂时无法实现替代或减量化。）
This table is prepared following the requirement of SJ/T 11364.
O: Indicates that the concentration of the substance in all homogeneous materials of the part is below the relevant
threshold specified in GB/T 26572.
X: Indicates that the concentration of the substance in at least one of all homogeneous materials of the part is above the
relevant threshold specified in GB/T 26572.
(Replacement and reduction of content cannot be achieved currently because of the technical or economic reason.)

Product specificaties

Merk: QSC
Categorie: Niet gecategoriseerd
Model: QIO-S4

Heb je hulp nodig?

Als je hulp nodig hebt met QSC QIO-S4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd QSC

QSC

QSC AcousticDesign YS8T Handleiding

26 Augustus 2024
QSC

QSC QIO-S4 Handleiding

27 Mei 2023
QSC

QSC Core 510i Handleiding

25 Mei 2023
QSC

QSC CXD4.3Q Handleiding

14 Mei 2023
QSC

QSC DPA-8K8Q Handleiding

13 Mei 2023
QSC

QSC Attero Tech unBT2A Handleiding

10 Mei 2023
QSC

QSC USL JSD-100 Handleiding

9 Mei 2023
QSC

QSC DPA 4.2 Handleiding

9 Mei 2023
QSC

QSC CX-Q 8K4 Handleiding

5 Mei 2023
QSC

QSC Q-SYS NV-32-H Handleiding

4 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Advantech

Advantech PCIE-1810-B Handleiding

14 November 2024
Advantech

Advantech PCIE-1805-AE Handleiding

14 November 2024
Advantech

Advantech PCI-1710U-DE Handleiding

14 November 2024
Advantech

Advantech PCIE-1816H-B Handleiding

14 November 2024
Advantech

Advantech SOM-2533AN0C-S0A1 Handleiding

14 November 2024
Advantech

Advantech SOM-2533DNCC-S8A1 Handleiding

14 November 2024
Advantech

Advantech PCE-4132G2-00A1 Handleiding

14 November 2024
Advantech

Advantech IDAQ-871-A Handleiding

14 November 2024
Advantech

Advantech IDAQ-801-AE Handleiding

14 November 2024
Advantech

Advantech IDAQ-841-AE Handleiding

14 November 2024