QSC Core Nano Handleiding

QSC Niet gecategoriseerd Core Nano

Lees hieronder de 📖 handleiding in het Nederlandse voor QSC Core Nano (14 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 190 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/14
TD-001615-00-A
*TD-001543-01*
™
Hardware User Manual
CORE NANO - NETWORK I/O PROCESSOR
CORE 8 FLEX - USB/FLEX CHANNELS
2
TD-001615-00-A
EXPLANATION OF TERMS AND SYMBOLS
The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.
The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in
damage to the equipment that may not be covered under the warranty.
The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.
The term "NOTE" is used to indicate additional useful information.
The intent of the lightning flash with arrowhead symbol within an equilateral triangle is to alert the user to the presence of un-insulated
"dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans.
The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important safety, and operating and
maintenance instructions in this manual.
IMPORTANT SAFETY INSTRUCTIONS
WARNING! TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the
rack environment may be greater than room ambient. Consideration should be given to ensure that the maximum operating temperature
range 0°C to 50°C (32°F to 122°F) is not exceeded. Reduced Air Flow – Installation of the equipment in a rack should be such
that the amount of airflow required for safe operation of the equipment is not compromised.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Do not submerge the apparatus in water or liquids.
7. Do not use any aerosol spray, cleaner, disinfectant or fumigant on, near or into the apparatus.
8. Clean only with a dry cloth.
9. Do not block any ventilation opening. Installation next to another unit within a rack should allow sufficient air flow required for safe operation.
10. Keep the side ventilation openings free of dust or other matter.
11. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
12. To reduce the risk of electrical shock, the power cord shall be connected to a mains socket outlet with a protecting earthing connection.
13. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
14. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the
apparatus.
15. Do not unplug the unit by pulling on the cord, use the plug.
16. Only use attachments/accessories specified by the manufacturer.
17. Unplug this apparatus during lightning storms or when unused for long periods of time.
18. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
19. The appliance coupler or the AC Mains plug is the AC mains disconnect device and shall remain readily accessible after installation.
20. Adhere to all applicable local codes.
21. Consult a licensed, professional engineer when in doubt or questions arise regarding a physical equipment installation.
3
TD-001615-00-A
Maintenance and Repairs
WARNING!: Advanced technology, e.g., the use of modern materials and powerful electronics, requires specially adapted
maintenance and repair methods. To avoid a danger of subsequent damage to the apparatus, injuries to persons and/or the creation of
additional safety hazards, all maintenance or repair work on the apparatus should be performed only by a QSC authorized service station
or an authorized QSC International Distributor. QSC is not responsible for any injury, harm or related damages arising from any failure of
the customer, owner or user of the apparatus to facilitate those repairs.
Limited Battery Warning
WARNING!: THIS EQUIPMENT CONTAINS A NON-RECHARGEABLE LITHIUM BATTERY. LITHIUM IS A CHEMICAL KNOWN TO THE STATE
OF CALIFORNIA TO CAUSE CANCER OR BIRTH DEFECTS. THE NON-RECHARGEABLE LITHIUM BATTERY CONTAINED IN THIS EQUIPMENT
MAY EXPLODE IF IT IS EXPOSED TO FIRE OR EXTREME HEAT. DO NOT SHORT CIRCUIT THE BATTERY. DO NOT ATTEMPT TO RECHARGE
THE NON-RECHARGEABLE LITHIUM BATTERY. THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED BY AN INCORRECT TYPE.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Expected Product Life Cycle: 20 years, Storage Temperature range: –20°F to +70°F, range of Relative Humidity:
5 - 85% RH non-condensing.
Warranty
For a copy of the QSC Limited Warranty, visit the QSC, LLC., website at www.qsc.com.
Para una copia de la Garantía Limitada de QSC, visite el sitio web de QSC, LLC., en www.qsc.com.
Pour obtenir une copie de la garantie limitée de QSC, visitez le site de QSC, LLC., à www.qsc.com.
Besuchen Sie die Webseite von QSC, LLC. (www.qsc.com) um eine Kopie der beschränkten Garantie von QSC zu erhalten.
Para uma cópia da garantia limitada da QSC visite o site da QSC, LLC., em www.qsc.com.
RoHS Statement
The QSC Q-SYS Core 8 FLEX Series is in compliance with European Directive 2011/65/EU – Restriction of Hazardous Substances (RoHS2).

Product specificaties

Merk: QSC
Categorie: Niet gecategoriseerd
Model: Core Nano

Heb je hulp nodig?

Als je hulp nodig hebt met QSC Core Nano stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd QSC

QSC

QSC AcousticDesign YS8T Handleiding

26 Augustus 2024
QSC

QSC QIO-S4 Handleiding

27 Mei 2023
QSC

QSC Core 510i Handleiding

25 Mei 2023
QSC

QSC CXD4.3Q Handleiding

14 Mei 2023
QSC

QSC DPA-8K8Q Handleiding

13 Mei 2023
QSC

QSC Attero Tech unBT2A Handleiding

10 Mei 2023
QSC

QSC USL JSD-100 Handleiding

9 Mei 2023
QSC

QSC DPA 4.2 Handleiding

9 Mei 2023
QSC

QSC CX-Q 8K4 Handleiding

5 Mei 2023
QSC

QSC Q-SYS NV-32-H Handleiding

4 Mei 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024
Kolcraft

Kolcraft MLB New York Yankees Handleiding

26 November 2024
Kolcraft

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024
Kolcraft

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024
Nedis

Nedis POCO106 Handleiding

26 November 2024
Nedis

Nedis BTSM1GY Handleiding

26 November 2024
Turbosound

Turbosound TPOLEAJ-01 Handleiding

26 November 2024
Turbosound

Turbosound TSTAND-01 Handleiding

26 November 2024
IFM

IFM TAD981 Handleiding

26 November 2024
IFM

IFM TAD961 Handleiding

26 November 2024