Pyle PAD15MXU Handleiding

Pyle Platenspeler PAD15MXU

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PAD15MXU (5 pagina's) in de categorie Platenspeler. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
3-Channel USB Audio/Sound Mixer Interface
with Built-in Rechargeable Battery
PAD15MXU
www.PyleUSA.com 1 2
IMPORTANT SAFETY INSTRUCTIONS
Read Instructions
Retain these safety and operating instructions for future reference. Heed all warnings
printed here and on the equipment. Follow the operating instructions printed in this
user guide.
Do not open
There are no user serviceable parts inside. Refer any service work to qualied technical
personnel only.
Power Sources
Only connect the unit to mains power of the type described in this user guide or
marked on the rear panel. The power source must provide a good ground connection.
Power Cord
Use the power cord with sealed mains plug appropriate for your local main supply as
provided with the equipment. If the provided plug does not t into you outlet consult
your service agent. Route the power cord so that it is not likely to be walked on,
stretched or pinched by items placed upon or against.
Grounding
Do not defeat the grounding and polarization means of the power cord plug. Do not
remove or tamper with the ground connection on the power cord.
Moisture
To reduce the risk of re or electrical shock, do not expose the unit to rain, moisture or
use in damp or wet conditions. Do not place container of liquid on it, which may spill
into any openings
Heat
Do not locate the unit in a place close to excessive heat or direct sunlight, as this could
be a re hazard. Locate the unit away from any equipment, which produces heat such
as: power supplies, power ampliers and heaters.
Environment
Protect from excessive dirt, dust, heat, and vibration when operating and storing. Avoid
tobacco ash, drink spillage and smoke especially that associated with smoke machines.
Handling
Protect the controls from damage during transit. Use adequate padding if you need to
ship the unit. To avoid injury to yourself or damage to the equipment take care when
lifting, moving or carrying the unit.
Servicing
Switch o the equipment and unplug the power cord immediately if it is exposed to
moisture, spilled liquid or the power cord or plug becomes damaged during a
lightning storm or if smoke odor or noise is noted. Refer servicing to qualied technical
personnel only.
Installation
Install the unit in accordance with the instruction printed in the user guide.
CAUTION
RISK OF ELECTRlC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
This symbol, wherever it appears, alerts you to
the presence of uninsulated voltages Dangerous
inside the enclosure that may be sucient to
constitute a risk of shock.
This symbol, wherever it appears, alerts you to
important operating and maintenance
instructions in the accompanying literature.
Please read the manual.
www.PyleUSA.com 3 4
OPERATING ELEMENTS AND CONNECTIONS
1. This combined jack can be used to connect mono signal such as MIC/LINE IN:
XLR microphone or 1/4” line level.
Note:
A. Please choose balanced cable and MIC to connect. Do not use the unbalanced
ones. When the unit is powered on, remember not to connect the high level
signal to XLR Mic In, which may damage the unit.
B. At the XLR jack, a phantom power of +18V is always present.
2. Stereo input LINE IN (RCA jacks) to connect an audio source with line signal
level (e.g. CD player) to channel CH2/ 3 .
3. Stereo input 2-TK (RCA jacks) to connect stereo line signal level sources.
4. Stereo outputs MAIN MIX (RCA jacks) to connect the input of an amplifier or a
recorder.
5. USB port (type B) to connect a computer or power supply unit with USB
connection. When operating the mixer with a computer, it is possible to use
this port as an audio output (output of the mixed signal) and as an audio input
(feed- in of audio data to be reproduced via channel LINE/USB)
6. Power/ Charge LED ON/ CHARGE
During battery operation of the unit and when the unit Not lighting up:
switched OFF and connected to a power supply and the battery is fully charged.
When the unit is switched OFF and connected to a power supply and Red light:
the battery is being charged.
Shows red and green (=yellow): When the unit is switched ON and connected
to a power supply and the battery is being charged
When the unit is switched ON and connected to a power supply Green light:
and the battery is fully charged
7. SwitchPOWER
8. Connections (MIC/PHONES)HEADSET
Note: Headset connected to the built-in microphone must be connected MIC IN
and PHONES in order to avoid unnecessary noise. The audio input is sent to
channel 1.
9. Echo Control to adjust the Echo eect component for channel CH1
10. 2TK/ET Control Switch: This is the assign control of 2TK input and Bluetooth
input. When this control is engaged, the signal of 2TK/ET will be assigned to
MONITOR (8). When the controls disengaged, the signal of2TK/BT Will be
Assigned to MAIN MIX (4) and USB (5).
11. Volume Control MONITOR/PHONES for the headphone output MONITOR/
PHONES (8).
12. Overload LEDs CLIP for the stereo output signal adjusted with the control
MAIN MIX (l4).
13. MAIN MIX Control to set the level of the output signal sent via the outputs
MAIN MIX (4) and the USB port (5).
14. Control GAIN for channel CH1 to set the input amplification.
15. High frequency control HI and low frequency control LO for channel CH1.
16. This is the panorama control or balanced control. This control is us ed for PAN
stereo eect field of the signal. Set this control in middle position, signal level
of Channel L & R will be same. When the control is set to top stop, only
Channel L receives the signal, Channel R can not. Vice versa
l7. This is clip LED indicator of CH1 level. When this LED illuminates, it PEAK LED
means that PFL CH1 level is clipped.
18. Control LEVEL for channel CH1.
19. From LINE IN/ USB Play source selector switch.: Pushing the button in, the
signal of channel LINE/U SB comes from USB PLAY(computer); When the
switch is disengaged, signal will be from RCA jacks of channel 2/ 3.
20. switch assigns signal to Main Mix or Monitor (Phones).LINE/USB
21. Control LEVEL for channel LINE/USB
APPLICATIONS
This compact 5-channel audio mixer with USB interface is suited for universal
applications, e. g. For audio recording on the computer.
The mono input channel allows to connect a (phantom-powered) microphone;
The stereo input channel allows to connect an audio source with line signal level.
In addition, the mixer is provided with connections for a recorder and head-
phones. The mixed signal is sent to the output via a RCA jacks and the USB port. It
is also possible to use the USB port as an input to transfer audio data from the
computer to the mixer. When connecting the mixer to a computer, power is
supplied via the USB connection. When operating the mixer without a computer,
either use a suitable power supply unit with USB connection to operate the mixer.


Product specificaties

Merk: Pyle
Categorie: Platenspeler
Model: PAD15MXU

Heb je hulp nodig?

Als je hulp nodig hebt met Pyle PAD15MXU stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Platenspeler Pyle

Handleiding Platenspeler

Nieuwste handleidingen voor Platenspeler