Psiber CM450 CableMaster Handleiding
Psiber
Meetinstrumenten
CM450 CableMaster
Lees hieronder de 📖 handleiding in het Nederlandse voor Psiber CM450 CableMaster (8 pagina's) in de categorie Meetinstrumenten. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
CableMaster
CM450
Quick Start Guide
Testing:
A. Plug the wire into the correct Test Port, Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button
Toning:
A. With the unit turned OFF, hold down the LENGTH/TONE button until
LCD illuminates
B. To select a tone cadence, press the LENGTH/TONE button repeatedly to step
through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you
reach the option you want. The option you select determines the cadence sent
from the main tester, through the cable, and picked up by the tone tracer probe.
C. Press the appropriate cable type button (voice, video, or data) to select a
cable for the tone signal
* Note: Tone is detected by a tone tracer probe
Length Measurement:
A. Make sure the CM450 is turned OFF.
B. Insert the cable plug into the corresponding receiver on the main tester (RJ-11
jack for voice cable, RJ-45 jack for data cables, F-Connector for video cables).
C. Press the LENGTH/TONE button to enter Length Mode.
D. Press the cable type button corresponding to the connector in use.
Features:
Testing: CM450 shows Opens, Shorts, Miswires, Split Pairs, PASS and
FAIL results quickly.
Toning: CM450’s built-in tone generator is a fl exible and function-packed
tone generator. Its confi gurable signal can be generated to fi nd and fi x the
position on any type of cable - either exposed or hidden, in ceilings or
behind walls.
Length: CM450 determines the length (in feet or meters) of an entire cable and/
or individual wire pairs within the cable.
Option: CM450 is supported by (1-19) wiremapping ID locators (Network/Coax)
and (1-8) testing/ID remotes (Network/Telephone).
Button Function
1. LCD Display
2. Voice Mode
3. Video Mode
4. Data Mode
1
4
3
6
7
5
2
5. Length/Tone Mode
6. On/Off and ID Mode
7. Main Unit Remote
(RJ11, RJ45)
CableMaster
CM450
Quick Start Guide
Kurzanleitung
Guide de Démarrage Rapide
CableMaster
CM450
Quick Start Guide
Testing:
A. Plug the wire into the correct Test Port, Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button
Toning:
A. With the unit turned OFF, hold down the LENGTH/TONE button until
LCD illuminates
B. To select a tone cadence, press the LENGTH/TONE button repeatedly to step
through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you
reach the option you want. The option you select determines the cadence sent
from the main tester, through the cable, and picked up by the tone tracer probe.
C. Press the appropriate cable type button (voice, video, or data) to select a
cable for the tone signal
* Note: Tone is detected by a tone tracer probe
Length Measurement:
A. Make sure the CM450 is turned OFF.
B. Insert the cable plug into the corresponding receiver on the main tester (RJ-11
jack for voice cable, RJ-45 jack for data cables, F-Connector for video cables).
C. Press the LENGTH/TONE button to enter Length Mode.
D. Press the cable type button corresponding to the connector in use.
Features:
Testing: CM450 shows Opens, Shorts, Miswires, Split Pairs, PASS and
FAIL results quickly.
Toning: CM450’s built-in tone generator is a fl exible and function-packed
tone generator. Its confi gurable signal can be generated to fi nd and fi x the
position on any type of cable - either exposed or hidden, in ceilings or
behind walls.
Length: CM450 determines the length (in feet or meters) of an entire cable and/
or individual wire pairs within the cable.
Option: CM450 is supported by (1-19) wiremapping ID locators (Network/Coax)
and (1-8) testing/ID remotes (Network/Telephone).
Button Function
1. LCD Display
2. Voice Mode
3. Video Mode
4. Data Mode
1
4
3
6
7
5
2
5. Length/Tone Mode
6. On/Off and ID Mode
7. Main Unit Remote
(RJ11, RJ45)
CableMaster
CM450
Quick Start Guide
Button Function
1 LCD Display 5 Length/Tone Mode
2 Voice Mode 6 On/Off and ID Mode
3 Video Mode 7 Main Unit Remote
4 Data Mode (RJ11/RJ12, RJ45)
English
A. Plug the wire into the correct Test Port, e.g. Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button
Toning:
A. With the unit turned OFF, hold down the LENGTH/TONE button until
LCD illuminates
B. To select a tone cadence, press the LENGTH/TONE button repeatedly to
step through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo 2. Stop
when you reach the option you want. The option you select determines the
cadence sent from the main tester, through the cable, and picked up by the
tone tracer probe*.
C. Press the appropriate cable type button (voice, video or data) to select a
cable for the tone signal
* Note: Tone is detected by a tone tracer probe (optional)
Length Measurement:
A. Make sure the CM450 is turned OFF.
B. Insert the cable plug into the corresponding receiver on the main tester
(RJ-11/RJ12) jack for voice cable, RJ-45 jack for data cables, F-Connector
for video cables).
C. Press the LENGTH/TONE button to enter Length Mode.
D. Press the cable type button corresponding to the connector in use
Features:
Testing: CM450 shows Opens, Shorts, Miswires, Split Pairs, PASS and
FAIL results quickly.
Toning: CM450`s built- in tone generator is a flexible and function- packed
Tone generator. Its configurable signal can be generated to find and fix the
position on any type of cable – either exposed or hidden, in ceilings or
behind walls.
Length: CM450 determines the length (in feet or meters) of an entire cable and/
or individual wire pairs within the cable.
Option: CM450 is supported by (1-19) wiremapping ID locators (Network/Coax)
and (1-8) testing/ID remotes (Network/Telephone).
English
Product specificaties
| Merk: | Psiber |
| Categorie: | Meetinstrumenten |
| Model: | CM450 CableMaster |
Heb je hulp nodig?
Als je hulp nodig hebt met Psiber CM450 CableMaster stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Meetinstrumenten Psiber
16 September 2023
Handleiding Meetinstrumenten
- Meetinstrumenten Bosch
- Meetinstrumenten Amprobe
- Meetinstrumenten AS - Schwabe
- Meetinstrumenten Beha-Amprobe
- Meetinstrumenten Benning
- Meetinstrumenten Brandson
- Meetinstrumenten Bresser
- Meetinstrumenten Burg-Wachter
- Meetinstrumenten Bushnell
- Meetinstrumenten Defort
- Meetinstrumenten Elma
- Meetinstrumenten Ferrex
- Meetinstrumenten Fluke
- Meetinstrumenten Gamma Scout
- Meetinstrumenten Gossen Metrawatt
- Meetinstrumenten Greenlee
- Meetinstrumenten Hema
- Meetinstrumenten Ideal Networks
- Meetinstrumenten Laserliner
- Meetinstrumenten Leica
- Meetinstrumenten Max
- Meetinstrumenten Megger
- Meetinstrumenten Mercury
- Meetinstrumenten Metrel
- Meetinstrumenten Milwaukee
- Meetinstrumenten Myoton
- Meetinstrumenten Perel
- Meetinstrumenten Powerfix
- Meetinstrumenten Profitec
- Meetinstrumenten Scubapro
- Meetinstrumenten Skandia
- Meetinstrumenten Skil
- Meetinstrumenten Stanley
- Meetinstrumenten Trotec
- Meetinstrumenten Uni-Trend
- Meetinstrumenten Voltcraft
- Meetinstrumenten Vonroc
- Meetinstrumenten Workzone
- Meetinstrumenten Probuilder
- Meetinstrumenten GMC Instruments
- Meetinstrumenten Hameg
- Meetinstrumenten Nieaf-Smitt
- Meetinstrumenten Sonel
Nieuwste handleidingen voor Meetinstrumenten
4 Oktober 2023
4 Oktober 2023
4 Oktober 2023
4 Oktober 2023
4 Oktober 2023
4 Oktober 2023
4 Oktober 2023
4 Oktober 2023
4 Oktober 2023
4 Oktober 2023