Praktica Luxmedia Z250 Handleiding

Praktica Fotocamera Luxmedia Z250

Lees hieronder de 📖 handleiding in het Nederlandse voor Praktica Luxmedia Z250 (86 pagina's) in de categorie Fotocamera. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/86

Preface

About this Manual

• The contents of this manual and the bundled Basic Reference are subject to

change without notice.

• Note that the example screens and product illustrations shown in this User’s

Guide may differ somewhat from the screens and configuration of the actual

camera.

This manual contains proprietary information protected by copyright. All rights

are reserved. No part of this manual may be reproduced by any mechanical,

electronic or other means, in any form, without prior written permission of the

manufacturer.

Declaration of Conformity

This device complies with Part 15 of the FCC rules. Operation is subject to the

following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference

that may cause undesired operation.

CE Mark Warning

This is a Class B product, in a domestic environment, this product may cause

radio interference, in which case the user may be required to take adequate

measures.

FCC: SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.27 W/Kg

CE: SAR standard Value: 2.0 W/Kg, Maximal Measure: 0. W/Kg 077

Trademark Recognition

Windows XP/Vista/Win7/Win 8 are registered trademarks of Microsoft

Corporation in the United States and/or other countries. Windows is an

abbreviated term referring to the Microsoft Windows Operation System. All

other companies or product names are trademarks or registered trademarks of

their respective companies.

Federal Communication Commission Interference Statement

APPLIES TO USA AND CANADA ONLY

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.



Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this

equipment.

This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

This device is intended only for OEM integrators under the

following conditions:

The antenna must be installed such that 20 cm is maintained between the

antenna and users, and

The transmitter module may not be co-located with any other transmitter or

antenna.

As long as 2 conditions above are met, further transmitter test will not be

required. However, the OEM integrator is still responsible for testing their

end-product for any additional compliance requirements required with this

module installed .

IMPORTANT NOTE: In the event that these conditions can not be met (for

example certain laptop configurations or co-location with another transmitter),

then the FCC authorization is no longer considered valid and the FCC ID can not

be used on the final product. In these circumstances, the OEM integrator will be

responsible for re-evaluating the end product (including the transmitter) and

obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna

may be installed such that 20 cm may be maintained between the antenna and

users. The final end product must be labeled in a visible area with the following:

"Contains FCC ID: 2AAD3AA0D0". The grantee's FCC ID can be used only when

all FCC compliance requirements are met.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user

regarding how to install or remove this RF module in the user’s manual of the

end product which integrates this module.

The end user manual shall include all required regulatory information/warnings

as shown in this manual.

Industry Canada statement

This device complies with RSS- of the Industry Canada Rules. Operation is 210

subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operatio n.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable

aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux

conditions suivantes: (1) le dispositif ne doit pas produire de brouillage

préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un

brouillage susceptible de provoquer un fonctionnement indésirable.

This device is intended only for OEM integrators under the

following conditions: (For module device use)

The antenna must be installed such that 20 cm is maintained between the

antenna and users, and

The transmitter module may not be co-located with any other transmitter or

antenna.

As long as 2 conditions above are met, further transmitter tests will not be

required. However, the OEM integrator is still responsible for testing their

end-product for any additional compliance requirements required with this

module installed.

Product specificaties

Merk:	Praktica
Categorie:	Fotocamera
Model:	Luxmedia Z250
Kleur van het product:	Zilver
Gewicht:	120 g
Breedte:	100.39 mm
Diepte:	21.45 mm
Hoogte:	59 mm
Bluetooth:	Nee
Beeldscherm:	LCD
Beeldschermdiagonaal:	2.7 "
Video recording:	Ja
Type stroombron:	Batterij/Accu
Meegeleverde kabels:	USB
Compatibele geheugenkaarten:	SDHC
Resolutie bij opnamesnelheid:	640x480@30fps
Snelstartgids:	Ja
Brandpuntbereik:	4.6 - 23 mm
USB-versie:	2.0
Zelfontspanner:	- s
Megapixels:	20 MP
Maximale beeldresolutie:	5152 x 3864 Pixels
Type beeldsensor:	CCD
Beeldsensorformaat:	1/2.3 "
Cameratype:	Compactcamera
Digitale zoom:	- x
Optische zoom:	5 x
ISO-gevoeligheid:	200,400,800,1600,3200,6400
Flits-bereik (wijd):	- m
Flits-bereik (tele):	- m
Maximale videoresolutie:	1280 x 720 Pixels
Framerate Motion JPEG:	30 fps
Ingebouwde microfoon:	Ja
Stemopname:	Ja
Intern geheugen:	64 MB
Videoresoluties:	640 x 480,1280 x 720 Pixels
Ondersteund beeldformaat:	JPEG XR
HDMI:	Nee
Fotoresolutie(s):	5152 x 3864
Geheugenslots:	1
USB-connector:	Mini-USB
Snelste camera sluiter snelheid:	- s
Langzaamste camera sluiter snelheid:	- s
ISO gevoeligheid (max):	6400
Wifi:	Nee
Batterijen inbegrepen:	Ja
Batterijtechnologie:	Lithium-Ion (Li-Ion)
Normaal scherpstelbereik (tele):	- m
Normaal scherpstelbereik (breed):	- m