Praktica Luxmedia Z212 Handleiding

Praktica Fotocamera Luxmedia Z212

Lees hieronder de 📖 handleiding in het Nederlandse voor Praktica Luxmedia Z212 (91 pagina's) in de categorie Fotocamera. Deze handleiding was nuttig voor 114 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/91

Preface

About this Manual

• The contents of this manual and the bundled Basic Reference are subject

to change without notice.

• Note that the example screens and product illustrations shown in this

User’s Guide may differ somewhat from the screens and configuration of

the actual camera.

This manual contains proprietary information protected by copyright. All rights

are reserved. No part of this manual may be reproduced by any mechanical,

electronic or other means, in any form, without prior written permission of the

manufacturer.

Declaration of Conformity

This device complies with Part 15 of the FCC rules. Operation is subject to the

following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference

that may cause undesired operation.

CE Mark Warning

This is a Class B product, in a domestic environment, this product may cause

radio interference, in which case the user may be required to take adequate

measures.

FCC: SAR standard Value: 1.6 W/Kg, Maximal Measure: 0.27 W/Kg

CE: SAR standard Value: 2.0 W/Kg, Maximal Measure: 0.077 W/Kg

Trademark Recognition

Windows XP/Vista/Win7/Win 8 are registered trademarks of Microsoft

Corporation in the United States and/or other countries. Windows is an

abbreviated term referring to the Microsoft Windows Operation System. All

other companies or product names are trademarks or registered trademarks

of their respective companies.

Federal Communication Commission Interference Statement

APPLIES TO USA AND CANADA ONLY

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the

following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this

equipment.

This transmitter must not be co-located or operating in conjunction with any

other antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

This device is intended only for OEM integrators under the following

conditions:

The antenna must be installed such that 20 cm is maintained between the

antenna and users, and

The transmitter module may not be co-located with any other transmitter

or antenna.

As long as 2 conditions above are met, further transmitter test will not be

required. However, the OEM integrator is still responsible for testing their end-

product for any additional compliance requirements required with this module

installed.

IMPORTANT NOTE: In the event that these conditions can not be met (for

example certain laptop configurations or co-location with another transmitter),

then the FCC authorization is no longer considered valid and the FCC ID can

not be used on the final product. In these circumstances, the OEM integrator

will be responsible for re-evaluating the end product (including the

transmitter) and obtaining a separate FCC authorization.

End Product Labelling

This transmitter module is authorized only for use in a device where the

antenna may be installed such that 20 cm may be maintained between the

antenna and users. The final end product must be labelled in a visible area

with the following: "Contains FCC ID: 2AAD3AA0D0". The grantee's FCC ID

can be used only when all FCC compliance requirements are met.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end

user regarding how to install or remove this RF module in the user’s manual

of the end product which integrates this module.

The end user manual shall include all required regulatory information/warning

as shown in this manual.

Industry Canada statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable

aux appareils radio exempts de licence. Son fonctionnement est sujet aux

deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage

préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris

un brouillage susceptible de provoquer un fonctionnement indésirable.

This device is intended only for OEM integrators under the following

conditions: (For module device use)

The antenna must be installed such that 20 cm is maintained between the

antenna and users, and

The transmitter module may not be co-located with any other transmitter

or antenna.

As long as 2 conditions above are met, further transmitter tests will not be

required. However, the OEM integrator is still responsible for testing their end-

product for any additional compliance requirements when this module is

installed.

Product specificaties

Merk:	Praktica
Categorie:	Fotocamera
Model:	Luxmedia Z212
Kleur van het product:	Wit
Gewicht:	127 g
Breedte:	100.9 mm
Diepte:	26.7 mm
Hoogte:	61.1 mm
Beeldscherm:	LCD
Beeldschermdiagonaal:	2.7 "
Ondersteunde videoformaten:	AVI
Video recording:	Ja
Type stroombron:	Batterij/Accu
Meegeleverde kabels:	USB
Compatibele geheugenkaarten:	MicroSD (TransFlash)
Resolutie bij opnamesnelheid:	640x480@30fps
Snelstartgids:	Ja
Brandpuntbereik:	4.3 - 51.6 mm
USB-versie:	2.0
Zelfontspanner:	- s
Megapixels:	20 MP
Maximale beeldresolutie:	5152 x 3864 Pixels
Type beeldsensor:	CCD
Beeldsensorformaat:	1/2.3 "
Cameratype:	Compactcamera
Digitale zoom:	- x
Optische zoom:	12 x
ISO-gevoeligheid:	200,400,800,1600,3200,6400
Flits-bereik (wijd):	- m
Flits-bereik (tele):	- m
Maximale videoresolutie:	1280 x 720 Pixels
Framerate Motion JPEG:	30 fps
Ingebouwde microfoon:	Ja
Stemopname:	Ja
Intern geheugen:	64 MB
Videoresoluties:	640 x 480,1280 x 720 Pixels
Ondersteund beeldformaat:	JPEG XR
Fotoresolutie(s):	5152 x 3864
Geheugenslots:	1
USB-connector:	Mini-USB
Snelste camera sluiter snelheid:	- s
Langzaamste camera sluiter snelheid:	- s
ISO gevoeligheid (max):	6400
Batterijen inbegrepen:	Ja
Batterijtechnologie:	Lithium-Ion (Li-Ion)
Normaal scherpstelbereik (tele):	- m
Normaal scherpstelbereik (breed):	- m