Posiflex LS-1000U Handleiding

Posiflex Barcode lezer   LS-1000U

Lees hieronder de 📖 handleiding in het Nederlandse voor Posiflex LS-1000U (22 pagina's) in de categorie Barcode lezer  . Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/22
FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual,
may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to EN55022 and 47
CFR, Part 2 and subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to
take whatever measures to correct the interference.
For CE-countries: This scanner is in conformity with CE standards. Please note that an approved, CE-marked power supply unit should be used in order to
maintain CE conformance.
Laser Safety: The laser scanner complies with safety standard IEC 60825 –1 for a Class I laser produce. It also complies with CDRH as applicable to a
Class IIa laser product. Avoid long term staring into direct laser light.
Radiant Energy: The laser scanner uses one low- -power visible laser diodes operating at 650nm in an opto mechanical scanner resulting in less than 3.9µW
radiated power as observed through a 7mm aperture and averaged over 10 seconds.
Do not attempt to remove the protective housing of the scanner, as unscanned laser light with a peak output up to 0.8mW would be accessible inside.
Laser Light Viewing: The scan window is the only aperture through which laser light may be observed from this product. A failure of the scanner motor,
while the laser diode continues to emit a laser beam, may cause emission levels to exceed those for safe operation. The scanner has safeguards to prevent
this occurrence. If, however, a stationary laser beam is emitted, the failing scanner should be disconnected from its power source immediately.
Adjustments: Do not attempt any adjustments or alteration of this product. Do not remove the protective housing of the scanner. There are no user-
serviceable parts inside.
Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.
Optical: The use of optical instruments with this product will increase the eye hazard. Optical instruments include binoculars, magnifying glasses, and
microscopes but do not include normal eye glasses worn by the user.
Warranty Limits: Warranty terminates automatically when any person other than the authorized technicians opens the machine. The user should consult
his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is
by no means responsible for any damage or hazard caused by improper application.
No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed, or translated into any language or
computer language in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without express
written consent and authorization.
We reserve the right to make changes in product design without reservation and without notification. The material in this guide is for
information only and is subject to change without notice.
All trademarks mentioned herein, registered or otherwise, are the properties of their various respective owners.
About This Manual:
Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this manual. However, Posiflex Technologies, Inc. will assume no
liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or
otherwise damages, including without limitation loss of data or profits, resulting from furnishing, performance, or use of this material.
This information is provided “ ”as is and Posiflex Technologies, Inc. expressly disclaims any warranties, expressed, implied or statutory, including without
limitation implied warranties of merchantability or fitness for particular purpose, good title and against infringement.
The information in this manual contains only essential hardware concerns for general user and is subject to change without notice. Posiflex Technologies,
Inc. reserves the right to alter product designs, layouts or drivers without notification. The system integrator shall provide applicative notices and
arrangement for special options utilizing this product. The user may find the most up to date information of the hardware from: http://www.posiflex.com or
http://www.posiflex.com.tw or http://www.posiflexusa.com
All data should be backed-up prior to the installation of any drive unit or storage peripheral. Posiflex Technologies, Inc. will not be responsible for any loss
of data resulting from the use, disuse or misuse of this or any other Posiflex product.
All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, or otherwise, without prior express written consent from Posiflex Technologies, Inc. the publisher of this
documentation.
© Copyright Posiflex Technologies, Inc. 2009
All brand and product names and trademarks are the property of their respective holders.
LS
-
1000 Series
Laser Barcode Scanner
User’s Manual
Rev. A0
P/N: 1805 0030090
Page 1
FUNDAMENTAL INFORMATION
MODEL NAME: LS-1000
CONTENT (Besides this guide):
Fig. 1 Box content besides this guide
INSTALLATION GUIDES
1. Install the USB or RS232 interface cable onto
the scanner by inserting the 8 pin RJ45 type
modular plug (Fig. 2) of the cable into the
scanner until a firm click is heard.
2. Use the stand fixing
screw to fit the stand on a
wooden desktop (Fig. 3).
3. Seat the scanner unit into the
stand and connect the
interface cable to an
appropriate USB or RS232
port (Fig. 4). Connect the
power adaptor to the power
input connector on interface cable (Fig. 5) or set the
+5V power support in pin 9 of the system COM port
for RS232 model. Set the COM port protocol to 9600, n,
8, 1 and no handshaking for RS232
model. Peel off the protective film on
scanner for ready to use after all the
operations done. The scanner will always
be in omni-directional scan mode when it
is in the stand.
Scanner Unit
Stand
Interface Cable
Stand Fixing Screw
Fig. 4 LS-1000 in Stand
Fig. 2 RJ45 Type Modular Plug
Fig. 3 Fix The Stand
Fig. 5 RS232 Power Connection
Page 2
Description Function
Scan Window Reads barcodes
Object Detector Trigger and wake up scanner automatically
when
presented with barcode in its range
Beeper Hole For beep tone indication
USING THE SCANNER
SCANNER INTRODUCTION
Features
The scanner unit is a compact and space- - -saving hands free omni directional laser
scanner. It can operate in a single-line laser scan mode by pressing down a button.
Featured with Z- -scan hardware decode technology, it guarantees the real time decode
and provide the best scanning performance you could expect.
The scanner includes key features as:
l Button switch in between omni-directional and single–line scanning
capability, ideal for increasing your operating efficiency.
l Powerful 20-line scan pattern yields:
ü 1400 scans per second for omni-directional scanning
ü 74 scans per second for single-line scanning
l Implement with the proprietary real-time hardware decoding technology
that ensures instant recognition and decoding barcodes
Parts Identification
Each part of the scanner as indicated in the front and rear pictures below is
described in the table below.
Function Button
Scan Window
Mounting Screw Hole
Object Detector
Beeper Hole
Interface Cable Connector
Page 3

Product specificaties

Merk: Posiflex
Categorie: Barcode lezer  
Model: LS-1000U
Kleur van het product: Zwart
Gewicht: 220 g
Gewicht basisstation: 200 g
Standaard interfaces: USB, PS/2

Heb je hulp nodig?

Als je hulp nodig hebt met Posiflex LS-1000U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Barcode lezer   Posiflex

Posiflex

Posiflex CD-3602U Handleiding

6 September 2024
Posiflex

Posiflex CD-3202U Handleiding

5 September 2024
Posiflex

Posiflex CD-3860UN Handleiding

5 Juni 2023
Posiflex

Posiflex LS-3000U Handleiding

25 Mei 2023
Posiflex

Posiflex CD-3870U Handleiding

21 Mei 2023
Posiflex

Posiflex CD-2860U-B Handleiding

20 Mei 2023
Posiflex

Posiflex CD-3601U Handleiding

18 Mei 2023
Posiflex

Posiflex CD-3201U Handleiding

15 Mei 2023
Posiflex

Posiflex LS-1000U Handleiding

14 Mei 2023
Posiflex

Posiflex LS-1000 Handleiding

12 Mei 2023

Handleiding Barcode lezer  

Nieuwste handleidingen voor Barcode lezer  

Honeywell

Honeywell Orbit HF680 Handleiding

16 November 2024
Honeywell

Honeywell Orbit MS7120 Kit Handleiding

16 November 2024
Brady

Brady IRX200 Handleiding

18 Augustus 2024
Newland

Newland HR33 Marlin filaire Handleiding

17 Augustus 2024
Wasp

Wasp WDI9600 Handleiding

31 Juli 2024
Wasp

Wasp WLS9500 Handleiding

29 Juli 2024
Wasp

Wasp WCS3900 Handleiding

29 Juli 2024
Wasp

Wasp WDI4600 Handleiding

29 Juli 2024
Wasp

Wasp WLR8900 Handleiding

29 Juli 2024
Wasp

Wasp WCS3905 Handleiding

29 Juli 2024