Platinum T129K1 Handleiding

Platinum Kabels voor pc's en randapparatuur T129K1

Lees hieronder de 📖 handleiding in het Nederlandse voor Platinum T129K1 (5 pagina's) in de categorie Kabels voor pc's en randapparatuur. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

Voice, Data, Video + Length

www.platinumtools.com

Instruction Sheet: P/N T129 GENERAL SPECIFICATIONS

The Platinum Tools, VDV MapMaster2.0™ is a portable voice-data-video cable

tester with length measurement. It tests and troubleshoots RJ11, RJ12, RJ45 and

F-conector terminated cables and provides built-in tone generation for cable tracing.

BATTERY REPLACEMENT

1) in the middle of the back Remove single screw

of the VDV MapMaster2.0™ with a #1 Phillips head

screwdriver. Remove the battery door.

2) and disconnect Remove the old battery

battery cable.

3) , 9 volt alkaline Replace with an ANSI 1604A

battery (Energizer 522, Duracell Mn1604). Reattach

cable and insert into battery compartment.

4) and screw. Replace battery door

DO NOT OVERTIGHTEN!

WARNINGS

To ensure safe operation and service of the tester, follow these instructions.

Failure to observe these warnings can result in severe injury or death.

•TheVDVMapMaster2.0™isdesignedforuseonunenergizedcabling

systems. Connecting the VDV MapMaster2.0 to live AC power may

damage it and pose a safety hazard for the user.

•PoorlyterminatedRJplugshavethepotentialtodamagethejacksonthe

VDV MapMaster2.0™. Visually inspect an RJ plug before inserting it into

the tester. The contacts should always be recessed into the plastic housing

of the plug. Plugging 6-position plugs into the 8-position jack on the

tester has the potential to damage the outermost contacts of the jack

unless the plug is speciﬁcally designed for that purpose.

Coax Type Belden P/N Center + Shield Maximum Length

RG-58A/U 8259 14.9 / 1,000 ft 6,710ft (2,045m)Ω

9311 25.8 / 1,000ft 3,876ft (1,182m)Ω

7806A 11.8 / 1,000ft 8,475ft (2,583m)Ω

RG-59/U 9310 24.1 / 1,000ft 4,150ft (1,265m)Ω

9259 23.5 / 1,000ft 4,255ft (1,297m)Ω

8241A 49.7 / 1,000ft 2,010ft (613m)Ω

9275 78.5 / 1,000 1,275ft (389m)Ω

9659 17.6 / 1,000ft 5,682ft (1,732m)Ω

RG-6/U 1694A 7.2 / 1,000ft 13,889ft (4,234m)Ω

1152A 29.8 / 1,000ft 3,360ft (1,025m)Ω

Mini Coax 9221 111 / 1,000ft 900ft (275m)Ω

RG-11/U 1523A 15.1 / 1,000ft 6,623ft (2,019m)Ω

•Dimensions:

6.4˝ x 2.8˝ x 1.4˝ (16.3 x 7.1 x 3.6 cm)

•Weight: 9.0 oz. (256 grams)

with battery and remote

•Operating Temperature:

0˚C/32˚F to 50˚C/122˚F

•Storage Temperature:

-20˚/-4˚F to 60˚C/140˚F

•Humidity: 10% to 90%,

non-condensing

•Maximum Voltage between

any two connector pins without

damage:

RJ Jack: 66V DC or 55V AC

F-Connector: 50V DC or AC

•Battery Life: 9V alkaline

battery typical

Standby: 4 years

Active: 425 hours

•Cable Types: Shielded or

Unshielded; Cat7, Cat6x, Cat5e,

Cat5, Cat4, Cat3, Coax

•Maximum RJ Cable Length:

0 to 1,000 feet (305 meters)

•Minimum Cable Length for Split

Pair Detection: 1.5 feet (0.5 meters)

•Low Battery: Icon ﬂashes when

battery voltage falls below 6V

•Measurement Technology:

Capacitance testing

•Length Accuracy Without

Length Constant Accuracy:

± 3% plus ± 1 foot

•Cable Length Measurement:

1 to 2,000 ft CAT5E cable with

15 pF/ft length constant

•Default Length Constant:

Restored with power on reset

  •Voice:17.4pF/ft

  •Video:16.5pF/ft

  •Data:15pF/ft

Complies with Conformité

Européenne directives.

•Maximum Coax Cable Length:

A B C

D E

1) The top line displays the cable type test mode or tone Mode:

generation mode.

2) Pass/Special Cables: “Pass” will be on if the cable is a properly

wired 4-pair T568A/B data cable, a 3-pair one-to-one wired voice

cable or a video cable with no faults. In addition, “X-over” illuminates

if a properly wired cross-over (uplink) cable is recognized or the

“Rev” illuminates if the cable is a properly wired reverse-pinned

voice cable. The wire map will show actual pin connections.

3) The “Fail” icon will be on only if the cable is not wired to Cable Faults:

one of the cabling standards. An open or short error takes precedence

DISPLAY

ID/Mapping: Pressing the O/ID button

starts the ID test mode on the VDV

MapMaster2.0™. Review section “E”

under category “KEYPAD”. ID/MAP

up to 19 locations at one time with

numbered custom ID remotes,

whether Voice (RJ12/11), Video (coax)

or Data (RJ45). Place ID remotes at

one end, the VDV MapMaster2.0™ at

the other end and start scanning. Mode Locator ID #

www.platinumtools.com

over miswires and the appropriate icon(s) illuminates. The “Split” icon

illuminates if the designated pairs are not twisted together in the cable,

an AC signal fault.

4) “Shielded” illuminates when a shielded data cable is properly Shield:

connected at both ends. It will be ﬂashing if there is a short to a wire

in the cable along with that pin number and the “Short” indicator.

5) Tester-End Wire Map: The top line displays the pins on the tester end

in order. These pins are mapped to the pins on the remote-end shown

directly below them on the LCD.

6) The bottom line displays the corresponding pin Remote-End Wire Map:

on the remote-end. Dash lines on the remote line indicate short pins.

No pin numbers displayed on the remote line are open pairs.

7) The battery low symbol illuminates when the battery is Battery Low:

nearing depletion. The symbol will begin to ﬂash when the battery needs

to be replaced. Results may be unreliable at this point.

8) In the video or the ID modes, the “ID” icon will be on with Location ID:

the number of the remote ID displayed or an error message of “Open”

or “Short”.

9) Voltage Detected Warning: If voltage is detected on any of the tester

connectors, the “Voltage!” icon is turned on. A check for voltage is

performed before each test and if found, no test is run. The tester

should be disconnected immediately from the source of the voltage.

KEYPAD

ID/MAPPING

A) Voice: Each press of the Voice button causes one test to be run on the

6-position RJ jack and the results displayed. The VDV MapMaster2.0™

will turn off after 20 seconds automatically. If the button is pressed and

held until “LOOP ON” is displayed, tests are run continuously and the

display updated until the O/ID button is pressed or after 5 minutes of no

change in results. Continuous mode is useful for trouble-shooting

intermittent problems.

 •InLengthMode,theyellowarrowallowsyoutoadjustthelength

constant value.

 •AshortpressoftheVoiceandVideobuttonssimultaneouslychanges

the length measurement unit from feet to meters.

B) Pressing the Video button starts the ID test, testing only Video:

for the F-connector, because the video continuity test is the same

as the ID test. The test loops continuously until the O/ID button is

pressed or for 5 minutes after the last change in ID status.

 •InLengthMode,theyellowarrowallowsyoutoadjustthe

length constant value.

 •AshortpressoftheVoiceandVideobuttonssimultaneously

changes the length measurement unit from feet to meters.

C) Data: Each press of the Data button causes one test to be run on the

8-position RJ jack and the results displayed. The VDV MapMaster2.0™

will turn off after 15 seconds automatically. If the button is pressed and

held until “LOOP ON” is displayed, tests are run continuously and the display

updated until the O/ID button is pressed or after 5 minutes of no change in

results. Continuous mode is useful for ﬁnding intermittent problems.

D) Length/Tone:

Tone Mode: When tone is pressed; the VDV MapMaster2.0™ begins

sending an audio tone for the connector last tested with the pins

and cadence previously selected for that connector type. To change the

connector type, press a different connector type button. Pressing the

same connector type button again, will change the pins carrying the tone.

Pressing the Tone button will cycle through the available tone cadences.

To turn the VDV MapMaster2.0™ off, press the O/ID button. The VDV

MapMaster2.0™ will turn off automatically 60 minutes after the last

button press. The tone is compatible with analog tone tracers.

Length Mode: When the LENGTH/TONE button is pressed, the measured

cable length (in units of feet or meters) appears in the lower right corner

of the LCD display screen and the “L” icon appears above pins 7 and 8 in

the Wire Map. The following values and icons display in the screen when

measuring cable length:

 •Edit Capacitance: A long press (two seconds) of the button allows you to

edit the length constant When adjusting the length constant value for a

cable, the “Edit Cap” icon appears in the bottom of the screen. An “E” icon \

displays above pins 7 and 8 in the Wire Map to indicate you are in Edit Mode.

 •Length Constant Value: A value, measured in picofarads (pF) per foot or

meter appears in the bottom of the LCD display screen. This value corre-

sponds to the selected cable type and can be adjusted at any time. When

viewing the length constant value for a cable type, the “C” icon displays

above pins 7 and 8.

E) Pressing O/ID will turn off the VDV MapMaster2.0™ when Off/ID (O/ID):

it is on in any mode. With the VDV MapMaster2.0™ off, pressing the O/ID

button starts the ID test mode. The ID test mode scans for all possible ID

types – voice, video and data. The “ID” icon and a progression of “o” are

displayed on the bottom line of the display to indicate scanning is active.

If no ID remotes are found, “Open” is displayed. When and ID remote is

found, the connector type and the ID number are displayed. If multiple ID

remotes are found, the ID or fault is displayed in sequence. The test loops

continuously until the I/OD button is pressed or for 5 minutes after last

change in ID status.

The RJ jacks share internal connections so only one RJ cable can be

connected at a time for accurate cable test results. However, an RJ

cable and a coax cable may be connected at the same time. In ID mode,

all connectors on the VDV MapMaster2.0™ may be connected at the

same time.

NOTE

Properly Wired T568A UTP:

T568B is electrically identical to T568A, but swaps the green and

orange pairs. Either standard will work as long as the same

standard is used at both ends of a run or patch cable. Mixing “A”

and “B” creates a cross-over cable.

Properly Wired T568A UTP:

T568A Cable with Split Pairs:

A common error in building a cable is to put all the pairs in pin

sequence 1-2, 3-4, 5-6 and 7-8. This will produce the correct

continuity, but the pairs are designated to be on pins 3-6 and

4-5 in the middle of the connector for compatibility with phone

wiring. This wiring error is only detected by the split pair test

since the designated pairs are not twisted together.

T568A Cable with Split Pairs:

T568A Cable with a Short and an Open:

The 1-2 pair pins are shorted together and the 7-8 pair is open.

The pins with the errors are ﬂashing. Dash lines (-) on the bottom

(remote) display line indicate the short, while no numbers on the

bottom line indicate the open pair.

T568A Cable with a

Short and Open:

T568A Cable with a Miswire and unrecognized Continuity:

1 and 2 pins on the VDV MapMaster2.0™ are connected to pins

2 and 1 at the remote-end. The pins with this error are ﬂashing.

The “U” for the remote pin numbers indicates an unrecognizable

continuity was detected that is neither a short or open. An ID

remote connected to the VDV MapMaster2.0™ when in cable

test mode would also show this error.

T568A Cable with a Miswire and

Unrecognized Continuity:

WIRING and DISPLAY EXAMPLES

www.platinumtools.com

= FLASHING

Product specificaties

Merk:	Platinum
Categorie:	Kabels voor pc's en randapparatuur
Model:	T129K1
Kleur van het product:	Rood
Gewicht verpakking:	256 g
Breedte verpakking:	71 mm
Hoogte verpakking:	163 mm
Meegeleverde kabels:	BNC, LAN (RJ-45)
Temperatuur bij opslag:	-20 - 60 °C
Lengte van de verpakking:	36 mm
Operating voltage:	55 V
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Type beeldscherm:	LCD
Ondersteunde aansluitingen:	BNC, RJ-11, RJ-12, RJ-45