Planet VIP-254PT Handleiding

Planet Telefoon VIP-254PT

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet VIP-254PT (52 pagina's) in de categorie Telefoon. Deze handleiding was nuttig voor 84 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/52
SIP IP Phone
VIP-254T/VIP-254PT
User’s manual
Version 1.0
1
Copyright
Copyright (C) 2008 PLANET Technology Corp. All rights reserved.
The products and programs described in this User’s Manual are licensed products of PLANET Technology, This
User’s Manual contains proprietary information protected by copyright, and this Users Manual and all
accompanying hardware, software, and documentation are copyrighted.
No part of this User’s Manual may be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form by any means by electronic or mechanical. Including photocopying, recording,
or information storage and retrieval systems, for any purpose other than the purchaser's personal use, and without
the prior express written permission of PLANET Technology.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
CE mark Warning
The is a class B device, In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Trademarks
The PLANET logo is a trademark of PLANET Technology. This documentation may refer to numerous hardware
and software products by their trade names. In most, if not all cases, their respective companies claim these
designations as trademarks or registered trademarks.
2
3
Revision
User’s Manual for PLANET SIP IP Phone:
Model: VIP-254T/VIP-254PT
Rev: 1.0 (2008, May)
Part No. EM-VIP254V1.0
5
Codec ID Setting ......................................................................................................33
DTMF Settings .........................................................................................................34
RPort Settings...........................................................................................................34
Other Settings ...........................................................................................................35
STUN settings ..........................................................................................................35
Auto Configuration...................................................................................................36
MAC CIone Setting..................................................................................................36
Tone Settings ............................................................................................................38
Advanced Settings ....................................................................................................38
System Authority ......................................................................................................39
Save & Reboot..........................................................................................................39
Firmware Upgrade....................................................................................................40
Auto Upgrade ...........................................................................................................40
Reset to Default ........................................................................................................42
Reboot without saving..............................................................................................43
Appendix A Voice communications...............................................................................44
Case 1: Voice communication via SIP proxy server _SIP-50...................................44
Case 2: Call Forward Feature_Example 1................................................................45
Case 3: Call Forward Feature_Example 4................................................................46
Appendix B The method of operation guide ................................................................48
Call Transfer .............................................................................................................48
3-Way Conference ....................................................................................................48
Call Waiting..............................................................................................................48
Switch the Realm (Registration Proxy Server) ........................................................49
Appendix C VIP-254T / VIP-254PT Specifications.....................................................50
Physical Details
The following figure illustrates the front/rear panel of IP Phone.
Rear View
Rear Panel of VIP-254T/VIP-254PT
1 PC RJ-45 connector, to maintain the existing network structure,
connected directly to the PC
through straight
CAT-5 cable
2 LAN
RJ-45 connector, for Internet access, connected directly to
Switch/Hub through straight CAT-5 cable.
The LAN interface also can be connected with 802.3af PoE
switch or converter for power supply (VIP-254PT)
3 DC 5V 5V DC Power input outlet
4. Handset
RJ-11 connector, connected directly to the Handset.
For VIP-254PT, either PoE or AC adapter can be deployed at
LNote
one time
8
Front View and Keypad function
Front Panel of VIP-254T/VIP-254PT
Keypad Description
1 LCD Display Menu and all status shall be displayed for users.
2 MENU To bring out the menu selection while IP Phone is in idle state.
3
This is Up / Down key and volume setting when
off-hook off.
Show the calls history when on-hook.
4 ENTER To be used as confirm configuration or enter sub-menu.
5 CONTACTS Enter the phone book selection.
6 FLASH
To transfer an active call (incoming call answered or outgoing
call accepted) to another devices.
7 CONF Press this button can make conference function.
8 FWD To carry out forward function.
9 DEL
Press to delete digits when at configuration mode or input
phone numbers.
Press to mute sounds when at talk mode.
9
Volume Setting
This page defines the Handset Volume, Ringer Volume, and the Handset Gain. When you finished the
setting, please click the Submit button.
Handset Volume is to set the volume for you can hear from the handset.(Handfree mode)
Speaker Volume is to set the volume for you can hear from the speaker.
Ringer Volume is to set the ringer volume for you can hear.
Handset Gain
is to set the volume send out
to the other side’s handset.
Speaker Gain
is to set the volume send out to the othe
r side’s handset from the microphone. (Handfree
mode)
Volume Settings for VIP-254T/VIP-254PT
21
LAN Settings
This page defines the LAN setting in this page.
LAN Mode: The default is Bridge mode, and it also provides NAT mode.
Bridge: When set as is mode, the LAN and PC ports are in the same network segment.
NAT: The LAN and PC ports are in the different network segment, and PC port could enable
the DHCP Server function to allot the IP address.
IP Type: The default is Fixed IP, and it also provides DHCP Client and PPPoE connection modes.
Fixed IP: It could setup the IP address manual.
DHCP Client: It will acquire the IP address automatically.
PPPoE: It will use the PPPoE connection method.
IP: The IP address
Mask: The sub net address
Gateway: The default gateway address
DNS Type: The default is Fixed mode, it could setup the DNS mode to manual or auto detection.
DNS Server1: The default is 168.95.192.1, it could setup the first DNS server address.
DNS Server2: The default is 168.95.1.1, it could setup the second DNS server address.
MAC: The MAC of LAN port
Host Name: The product model
User Name:
The PPPoE connection account name. It could in
pout numeral or character, the maximum
date length are 63.
Password: The PPPoE connection account password. It could inpout numeral or character, the
maximum date length are 63.
26
PC Settings
This page defines the PC setting in this page.
IP: The IP address of PC port. (In the Bridge
mode, the
Default IP: 192.168.123.1)
Mask: The sub net address. (Default: 255.255.255.0)
MAC: The MAC of PC port
DHCP Server: It will allot the IP address automatically when enabke this function.
Start IP: Start IP of lease table
End IP: End IP of lease table. Network device connecting to the PC port can dynamic obtain the IP in
the range between start IP and end IP
Lease Time: DHCP server lease time
27
DDNS Settings
This page defines the DDNS setting in this page. You need to have the DDNS account and input the
informations properly. You can have a DDNS account with a public IP address then others can call you
via the DDNS account. But now most of the VoIP applications are work with a SIP Proxy Server. When
you finished the setting, please click the Submit button.
28
VLAN Settings
This page defines the VLAN setting in this page. This function needs to co-operate with network
devices which have VLAN function.
VLAN Packets: If setup as On, it could receive VLAN messages.
VID (802.1Q/TAG): Dispose VLAN ID is add a Tag header after realize enable the VLAN function. The
realized voice packets transfer at the same VLAN. The prerequisite is it must the
same as VLAN of upper switch. The value range are 2~4094.
User Priority (802.1P): To setup the user priority.
CFI: To indicate the Canonical Format.
If CFI=1, it means the header label include RIF field, and the NCIF flag valus of RIF will to
decide the MAC address is Canonical Format or Non-Canonical Format in frame information.
If CFI=0, it means the header label does not include RIF field, and the MAC address is
Canonical Format in frame information.
DMZ Settings
This page defines the DMZ setting in this page.
DMZ: If setup as On, all of packets (expect SIP packets) will send to the specific IP address.
DMZ Host IP: The DMZ host IP address.
29
Virtual Server
This page defines the Virtual Server setting in this page. You could define 24 virtual service information
in this page. When you finished the setting, please click the Submit button.
Virtual Server Page: There are total page1 to page 3. It could choose the page which want to go over.
Num: The serial number. There are total 24 records from Num 0 to 23.
Enable: The activate status. The default is Disable, this record will been activate if enable.
Protocol: The TCP or UDP communication protocol.
Internal Port: For corresponding the internal port.
External Port: For corresponding the external port.
Server IP: To input the Server IP address.
30
PPTP Settings
This page defines the PPTP setting in this page. You could setup the PPTP Server connection
information. When you finished the setting, please click the Submit button.
Service Domain Settings
This router comes with the built-in firewall based on the advanced technology of Stateful Packet
In Service Domain Function you need to input the account and the related informations in this page,
please refer to your ISP provider. You can register three SIP account in the Phon. You can dial the VoIP
phone to your friends via first enable SIP account and receive the phone from these three SIP
accounts.
First you need click Active to enable the Service Domain, then you can input the following items:
Display Name: you can input the name you want to display.
User Name: you need to input the User Name get from your ISP.
Register Name: you need to input the Register Name get from your ISP.
Register Password: you need to input the Register Password get from your ISP.
Domain Server: you need to input the Domain Server get from your ISP.
Proxy Server: you need to input the Proxy Server get from your ISP.
Outbound Proxy: you need to input the Outbound Proxy get from your ISP. If your ISP does not
provide the information, then you can skip this item.
You can see the Register Status in the Status item. If the item shows “Registered”, then your Phone
Adapter is registered to the ISP, you can make a phone call direcly.
If you have more than one SIP account, you can following the steps to register to the other ISP.
When you finished the setting, please click the Submit button.
31
L
L
L
LLNote:
IP Phone can register to three different SIP Proxies at the same time. It can receive any one of
different SIP accounts incoming call, and it can switch to any one SIP accounts for making calls
through input the switch code.
Realm switch code:
1*: Realm 1
2*: Realm 2
3*: Realm 3
For example: The default is realm 1, input the 2* (Follow by the # key) from keypad and hang up
the telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2.
Port Settings
This page defines the SIP and RTP port number in this page. Each ISP provider will have different
SIP/RTPport setting, please refer to the ISP to setup the port number correctly. When you finished the
setting, please click the Submit button.
32
DTMF Settings
This page defines the DTMF parameters. Yyou can setup the InBand DTMF, 2833 Out-Band DTMF and
Send DTMF SIP Info Enable/Disable in this page. To change this setting, please following your ISP
information. When you finished the setting, please click the Submit button.
RPort Settings
This page defines the RPort Enable/Disable in this page. To change this setting, please following your
ISP information. When you finished the setting, please click the Submit button.
34
Other Settings
This page defines the Hold by RFC, Voice/SIP QoS and other settings in this page. To change these
settings please following your ISP information. When you finished the setting, please click the Submit
button.
Hold by RFC: The default is disable, and to start up communication hold back function (RFC definition).
Set enable to start up the Hold by RFC function.
Voice QoS (Diff-Serv): The Voice QoS feature.
SIP QoS (Diff-Serv): The SIP QoS feature.
The QoS setting is to set the voice packets’ priority. If you set the value higher than 0, then the voice
packets will get the higher priority to the Internet. But the QoS function still need to cooperate with the
others Internet devices.
SIP Expire Time: To setup the registration interval time.
Use DNS SRV: The default is disable, and use DNS SRV mode. Set enable to use DNS to SRV mode
to search the host information.
Send Keep Alives Pcaket: To deliver the packets on a regular time schedule to keep NAT port could
open continued.
Keep Alives Period: To setup the schedule time for delivering the packets.
Jitter Buffer: To setup the Jitter Buffer size, and the unit is packet. It needs to refer to the Frame size of
Codec.
STUN settings
This page defines the STUN Enable/Disable and STUN Server IP address in this page. This function
can help your Phone Adapter working properly behind NAT. To change these settings please following
your ISP information. When you finished the setting, please click the Submit button.
35
Firmware Upgrade
In Firmware Upgrade function you can update new firmware via HTTP or TFTP methods in this page.
You can ugrade the firmware by the following steps:
Select the upgrade method and the firmware code type, AP or DSP code.
Click the “Browse” button in the right side of the File Location or you can type the correct path and the
filename in File Location blank.
Select the correct file you want to download to the device then click the Update button.
L
L
L
LLNote:
After firmware loaded, the unit will be reboot, and Default IP address of the customized firmware:
http://192.168.0.1; login name/password: root/null (no password)
Auto Upgrade
The device can update new firmware with the gz or ds file format automatically by the Auto Upgrade
function.
40
Field Descriptions
Update via There are TFTP/ FTP and HTTP three ways to provide the auto
upgrade function.
TFTP Server Input the TFTP Server address, and it could input the IP or Domain
Name form.
TFTP Path Set up the file path.
HTTP Server Input the HTTP Server address, and it could input the IP or Domain
Name form.
HTTP File Path Set up the file path.
FTP Server Input the FTP Server address, and it could input the IP or Domain
Name form.
FTP Username The login username.
FTP Password The login password
FTP File Path Set up the file path.
Check new firmware The device will according to the below ways to check the new
firmware.
- Power On and Scheduling: The machine will check the
41
new firmware when power on and following the scheduling
date and time.
- Scheduling only: The machine will only follow the
scheduling date and time to check the new firmware.
Scheduling (Date) The machine will check the new firmware between the time range
by random.
Automatic Update There are Notify only and Automatic ways to update.
- Notify only: If there are new firmware, the IP Phone will
send the “Be Be Be” sounds when pick up the handset to
prompt there are new firmware.
- Automatic: The device will carry firmware update out
automatically.
Firmware File Prefix It will check the information of model name.
Next update time It will show the next check date and time.
L
L
L
LLNote:
If the Check new firmware field selected to Power On, the machine will chck the new
firmware accoeding the scheduling time/date and power on. If there are new firmware can
be upgraded, the machine won’t carry firmware update out automatic. The machine will
show the [Found New s/w] message on LCD. Then press [Menu] button for entrying the
main menu and select the [7.Administrator -> 2. Upgrade System -> 1.Upgrade Now]
selection to carry out the upgrade firmware action.
Reset to Default
In Default Setting you can restore the IP Phone to factory default in this page. You can just click the
Restore button, then the IP Phone will restore to default and automatically restart again.
42
STEP 3:
Repeat the same configuration steps on VIP-254T-B, and check the machine
registration status, make sure the registrations are completed.
STEP 4:
To verify the VoIP communication, please pick up the telephone. Dial the destination number
to make call between SIP clients. For example, VIP-254T-A (with number 100) with keypad
number 200 to VIP-254T-B, or reversely makes calls from SIP client (VIP-254T-B) to the
number 100 (VIP-254T-A).
Case 2: Call Forward Feature_Example 1
In the following samples, we’ll introduce the Call Forward Feature applications.
In this example, there are three VIP-254T register to IPX-300 and VIP-254T_A had set Call Forward
function to VIP-254T_B. (The detail registration settings of IPX-300 and VIP-254T please refer to the
instruction of Case 3)
VIP-254T_A VIP-254T_B VIP-254T_C
Machine configuration on the VIP-254T:
STEP 1:
Please log in VIP-254T_A via web browser, browse to the Phone Settings menu and select
the Call Forward config menu. In the setting page, please enable the All Forward function
and fill in the Name
and URL
of VIP-254T_B, then the sample
configuration screen is shown
below:
45
STEP 2:
After set up completed and reboot machine, the LCD screen will show below:
10-19 17:20
# Forward #
After 2~3 seconds, the LCD screen will show below:
10-19 17:20
AF 2002
Test the scenario:
VIP-254T_C pick up the telephone and dial the number 1001(VIP-254T_A), because VIP-254T_A had
set up All Forward function to the number 2002(VIP-254T_B), so the number 2002(VIP-254T_B) will
ring up then it pick up the telephone and communication with the number 3003(VIP-254T_C).
Case 3: Call Forward Feature_Example 4
In this example, there are three VIP-254T and connect with Peer to Peer mode. VIP-254T_A had set
Call Forward function to VIP-254T_B.
46
VIP-254T_B VIP-254T_C
VIP-254T_A
48
Appendix B The method of operation guide
In this section, well introduce the features method of operation, and lead you step by step to establish
these features.
Call Transfer
A. Blind Transfer
1. B call to A and they are in the process of conversation.
2. A press and input the number of C (Follow by FLASHbutton to hold the conversation with B,
the “#” key).
3. C will ring up, and A hang up the handset.
4. C picks up the handset and conversation with B.
B. Attendant Transfer
1. B call to A and they are in the process of conversation.
2. A press and input the number of C (Follow by FLASHbutton to hold the conversation with B,
the “#” key).
3. C will ring up.
4. C picks up the handset and conversation with A.
5. A hang up and C conversation with B.
3-Way Conference
1. A and B are in the process of conversation.
2. A want to invite C to join their conversation.
3. A press and input the number of C (Follow by FLASHbutton to hold the conversation with B,
the “#” key).
4. C will ring up and pick up the handset to conversation with A.
5. A press “CONF” button and they will entry the 3-Way conference mode.
Call Waiting
1. A and B are in the process of conversation.
2. C call to A and A will hear the prompt sounds.
3. A press “Hold” button to hold the conversation with B, and switch to conversation with C.
49
Switch the Realm (Registration Proxy Server)
IP Phone can register to three different SIP Proxies at the same time. It can receive any one of different
SIP accounts incoming call, and it can switch to any one SIP accounts for making calls through input
the switch code.
Realm switch code:
1*: Realm 1
2*: Realm 2
3*: Realm 3
For example: The default is realm 1, input the 2* (Follow by the # key) from keypad and hang up the
telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2.
50
Appendix C VIP-254T / VIP-254PT Specifications
Product SIP IP Phone SIP PoE IP Phone
Model VIP-254T VIP-254PT
Hardware
LAN 1 x 10/100Mbps RJ-45 port
Power Over Ethernet 802.3af compliant at VIP-254PT
PC 1 x 10/100Mbps RJ-45 port
LCD display 2 x 16 characters
Speaker Full duplex hands free speaker phone
Protocols and Standard
Standard SIP 2.0 (RFC3261), MD5 for SIP authentication (RFC2069/ RFC 2617), SIP
outbound proxy, SIP NAT Traversal Support STUN (RFC3489)
Voice codec G.711: 64k bit/s (PCM)
G.723.1: 6.3k / 5.3k bit/s
G.726: 16k / 24k / 32k / 40k bit/s (ADPCM)
G.729A: 8k bit/s (CS-ACELP)
G.729B: adds VAD & CNG to G.729
Voice Standard Voice activity detection (VAD)
Comfort noise generation (CNG)
Acoustic echo canceller (AEC)
G.165: Line echo canceller (LEC)
Jitter Buffer
Supplementary services Caller ID
3-way conference
Immediate (unconditional) call forwarding
Busy call forwarding
No answer calls forwarding
Call Hold/Waiting/Transferring
Call history Record incoming call
Outgoing call
Missed (not accepted) call history
Protocols SIP v1 (RFC2543), v2(RFC3261), TCP/IP, UDP/RTP/RTCP, HTTP, ICMP, ARP,
RARP, DNS, DHCP, SNTP, PPPoE
Network and Configuration
Access Mode Static IP, PPPoE, DHCP
Management Web, LCD menu keypad, auto-provision by TFTP/FTP/HTTP
Dimension (W x D x H) 184 mm x 200 mm x 48 mm
Operating Environment 0~50 degree C, 0~90% humidity
Power Requirement 5V DC, 1A
Power Over Ethernet 802.3af compliant at VIP-254PT
EMC/EMI CE, FCC Class B


Product specificaties

Merk: Planet
Categorie: Telefoon
Model: VIP-254PT
Kleur van het product: Zwart
Breedte: 184 mm
Diepte: 200 mm
Hoogte: 48 mm
Bluetooth: Nee
Beeldscherm: LCD
Touchscreen: Nee
Stemcodecs: G.711,G.723.1,G.726,G.729A
Ethernet LAN: Ja
Luidspreker: Ja
Wachtstand: Ja
Gesprek in de wacht zetten: Ja
Nummerherkenning: Ja
Conferentiegesprek mogelijk: Ja
Aantal Ethernet LAN (RJ-45)-poorten: 2
Volumeregeling: Digitaal
Certificering: FCC, CE
Voldoet aan industriestandaarden: IEEE802.3, IEEE802.3u, IEEE802.3af
Ruisonderdrukking: Ja
Ondersteunde netwerkprotocollen: SIP v1/2, TCP/IP, UDP/RTP/RTCP, HTTP, ICMP, ARP, RARP, DNS, SNTP
Aantal handvatten opgenomen: 1 stuk(s)
DHCP client: Ja
Power over Ethernet (PoE): Ja
Handset type: Handset met snoer
Capaciteit telefoonboek: - entries
Lijn-kwantiteit: - regels
Beheerplatform: TFTP/FTP/HTTP, Telnet
Bedrijfstemperatuur (T-T): 0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V): 0 - 95 procent
Type product: IP Phone
Gesprekken naar een andere telefoon omleiden: Ja
Echo annulatie: Ja
Stem activiteit detectie: Ja
Aanpasbare jitter buffers: Ja

Heb je hulp nodig?

Als je hulp nodig hebt met Planet VIP-254PT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Telefoon Planet

Handleiding Telefoon

Nieuwste handleidingen voor Telefoon

VTech

VTech CS6919 Handleiding

13 December 2024
VTech

VTech CS6929 Handleiding

13 December 2024
VTech

VTech CS6919-2 Handleiding

13 December 2024
VTech

VTech CS6929-26 Handleiding

13 December 2024
VTech

VTech VCS704 Handleiding

13 December 2024
VTech

VTech CS6929-4 Handleiding

13 December 2024
VTech

VTech CS6124-31 Handleiding

13 December 2024
VTech

VTech CS6114 Handleiding

13 December 2024