Planet POE-E304 Handleiding

Planet Wifi-repeater POE-E304

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet POE-E304 (4 pagina's) in de categorie Wifi-repeater. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

1. Package Contents

Thank you for purchasing PLANET 1-port Ultra PoE+ to 4-port IEEE

802.3af/at Gigabit PoE Extender, POE-E304. “Gigabit PoE Extender”

mentioned in this manual refers to the POE-E304.

Open the box of the Gigabit PoE Extender and carefully unpack it. The

box should contain the following items:

Gigabit PoE Extender x 1 User’s Manual x 1

Rubber Feet x 4 Wall-mount Kit

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing

material, and use them again to repack the product in case there is a

need to return it to us for repair.

Features Store-and-Forward mode with wire-speed ltering and

forwarding rates

IEEE 802.3x ow control for full duplex operation and backpressure

for half duplex operation

Automatic address learning and address aging

 Case and Installation

No external power cable installation required

Made of metal, desktop size design

Wall-mountable, Plug-and-Play installation

0 ~ 50 degrees C operating Temperature

Note

PSE (Power Sourcing Equipment) is a device (switch

or hub for instance) that will provide power in a PoE

setup. The maximum allowed continuous output power

per such device in IEEE 802.3af is 15.4 watts and in IEEE

802.3at is 30 watts.

PD (Powered Device) such as IP phones, network

cameras or wireless access points is a PoE-enabled

terminal that consumes energy supplied by PSE.

4. Hardware Introduction

4.1 Three-View Diagram

The three-view diagram of the Gigabit PoE Extender consists of one

auto-sensing 10/100/1000BASE-T Ultra PoE In port, and four auto-

sensing 10/100/1000BASE-T 802.3af/802.3at PoE Out ports. The LED

Indicators are also located on the port of Gigabit PoE Extender front

panel.

PoE In-Use

PoE MAX

PWR

1 2 3 4

541 2

PoE OUT PoE IN

10/100

1000

LNK ACT

Figure 1: POE-E304

Protection ESD (Ethernet): 6KV

Surge (EFT for power): 2KV

Enclosure Metal

Installation Desktop/Wall mountable

Dimensions

(W x D x H) 160 x 92.5 x 28mm

Weight 370g

Power

Requirements

PoE In: IEEE 802.3bt or 4-pair 802.3at PoE+

compliant with voltage within 50V-56V DC

External DC: 50~56V DC

Power

Consumption

4 watts/13.7BTU (System on with PoE input)

6 watts/20.6BTU (Ethernet full loading without PoE

function)

60 watts/205.9BTU (Full loading with PoE function)

Network Cable

10BASE-T: 4-pair UTP Cat5 up to 100m (328ft)

100BASE-TX: 4-pair UTP Cat5 up to 100m (328ft)

1000BASE-T: 4-pair UTP Cat5e, 6, up to 100m

(328ft)

EIA/TIA-568 100-ohm STP (100m, 328ft)

Power over Ethernet

PoE Standard

PoE In Port

Ultra Power over Ethernet end-span/mid-span PD

class 4 PD

Per PoE Out Port

IEEE 802.3at Power over Ethernet Plus end-span

PSE

IEEE 802.3af Power over Ethernet end-span PSE

2. Product Features

 Physical Port

5-port 10/100/1000BASE-T Gigabit RJ45 interface

- 1-port data + power input

- 4-port data + power output

 Power over Ethernet

1-port data + power input

- Complies with Ultra Power over Ethernet end-span/mid-span PD

- Supports PoE input power up to 60 watts

4-port data + power output

- Complies with IEEE 802.3af/IEEE 802.3at Power over Ethernet/

end-span PSE

- Up to 4 IEEE 802.3af/802.3at devices powered

- Supports PoE power up to 30.8 watts for each PoE port

- Auto detects powered device (PD)

Extends the range of PoE to an additional 100 meters (328ft.)

Forwards both Ethernet data and PoE power to remote device

 Layer 2 Features

Hardware based 10/100/1000Mbps auto-negotiation and auto MDI/

MDI-X

Integrates address look-up engine, supporting 2K absolute MAC

addresses

9K Jumbo packet support

IEEE 802.1Q VLAN transparency

PoE Power

PoE In Port

50~56V DC, max. 60 watts

Per PoE Out Port

44~55V DC, max. 30.8 watts

Power Pin

Assignment

PoE In Port

1/2 (+), 3/6 (-); 4/5 (+), 7/8 (-) or 1/2(-), 3/6(+);

4/5(+), 7/8(-)

Per PoE Out Port

1/2 (+), 3/6 (-), end-span (Type A)

PoE Power

Budget

50 watts (max.) @ Ultra PoE input

20 watts (max.) @ IEEE 802.3at PoE+ input

Standard Conformance

Regulatory

Compliance FCC Part 15 Class A, CE

Standard

Compliance

IEEE 802.3 10BASE-T Ethernet

IEEE 802.3u 100BASE-TX Fast Ethernet

IEEE 802.3ab 1000BASE-T Gigabit Ethernet

IEEE 802.3af Power over Ethernet

IEEE 802.3at Power over Ethernet Plus

IEEE 802.3x Flow Control

Environment

Operating Temperature: 0 ~ 50 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

Storage Temperature: -10 ~ 70 degrees C

Relative Humidity: 5 ~ 95% (non-condensing)

Note

The maximum distance that data and power can transmit

depends on the quality of the UTP cable and environment.

4.2 Ports Connection

PoE IN Port

Connect the port from the following Ultra PoE IN PSE

devices through a Cat5/5e/6 UTP cable:

 Ultra PoE injector

 Ultra PoE injector hub

 Ultra PoE Ethernet switch

PoE OUT Port

Connect the port to the following 802.3at/af PoE OUT

PD devices through a Cat5/5e/6 UTP cable:

 PoE IP camera

 PoE VoIP phone

 PoE wireless AP

 PoE splitter

4.3 LED Indicators

Ultra PoE IN Port

LED Color Function

10/100 LNK/

ACT Orange

Lights to indicate the link through that port is

successfully established at 1000Mbps.

Blinks to indicate that the port is actively

sending or receiving data.

1000

LNK/ACT Green

Lights to indicate the link through that port is

successfully established at 1000Mbps.

Blinks to indicate that the port is actively

sending or receiving data.

3.ProductSpecications

Model POE-E304

Hardware Specications

Network

Connector

PoE In Port

1 x 10/100/1000BASE-T Ethernet with Ultra PoE

b in, auto MDI/MDI-X, auto-negotiation RJ45

connector

PoE Out Port

4 x 10/100/1000BASE-T Ethernet with IEEE

802.3at/802.3af PoE out, auto MDI/“Data + DC”

MDI-X, auto-negotiation RJ45 connector

Data Rate 10/100/1000Mbps

Switch

Architecture Store-and-Forward

MAC Address

Table 2K

Data Buffer 2Mbits

Switch Fabric 10Gbps

Switch

Throughput 7.44Mpps @ 64 bytes

Jumbo Frame 9K

Flow Control IEEE 802.3x pause frame for full duplex

Back pressure for half duplex

LED Indicators

PoE In Port

10/100 LNK/ACT ( ), 1000 LNK/ACT (orange green)

PoE Out Port 1 to Port 4

10/100 LNK/ACT ( ), 1000 LNK/ACT (orange green)

PoE-in-Use (orange)

PoE Max. (orange)

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

802.3at/af PoE Out Ports

LED Color Function

10/100

LNK/ACT Orange

Lights to indicate the link through that port is

successfully established at 1000Mbps.

Blinks to indicate that the port is actively

sending or receiving data.

1000

LNK/ACT Green

Lights to indicate the link through that port is

successfully established at 1000Mbps.

Blinks to indicate that the port is actively

sending or receiving data.

PoE-in-Use

LED Color Function

PoE Max. Orange Lights to indicate the power usage is ≥ 45W

Blinks to indicate the power usage is ≥ 55W

PoE-in-Use Orange Lights to indicate the port is providing 50V-56V

DC in-line power output

5. Hardware Installation

5.1 Before Installation

The POE-E304 is installed between the PSE (Power Source Equipment)

and the PD (powered device); it is powered by PSE and forwards the

Ethernet data and remaining POE power or an external power supply

to the PD and it can be installed easily by just plug and play without

affecting the data transmission performance.

Note

1. When the PoE-in-use LED turns steady orange,

it means the Gigabit PoE OUT is supplying power

successfully from PSE.

2. If the PoE-in-use LED is not lit, please check the

remote PSE or the cable connecting to a PC or a

network device to see if the cable is correct.

Never connect any POE PSE to the Gigabit non-standard

PoE Extender; it will damage the device permanently.

5.3 Connecting POE-E304 to Powered Device (PD)

Step 1: Connect the additional Cat5e/6 cable that will be used to

connect to the remote to the Powered Device (PD) “PoE

Out” port of the Gigabit PoE Extender.

Ultra PoE Switch

PoE Wireless AP

UTP

PoE Camera

UTP

PoEPoE

PoE

PoE In-U se

PoE M AX

PWR

1234

541 2

PoE OUT PoE IN

10/100

1000

LNK ACT

Step 2: The "PoE Out" port is also the power injector which transmits

DC voltage to the Cat5e/6 cable and transfer data and power

simultaneously between the PSE and PD.

Note

1. To provide you with better PoE power and data

extension quality, we strongly recommend that you use

“Solid UTP Cable” when installing the POE-304.

2. The POE-E304 can be installed with a third-party device

if the device complies with IEEE 802.3at/af standard.

5.2 Connecting POE-E304 to PSE

This section describes how to install Gigabit PoE Extender and make

connection to it. Please read the following topics and perform the

procedures in the order being presented.

There are 4 RJ45 ports in the Gigabit PoE Extender, of which the “PoE

IN” port functions as "PoE (Data and Power) input" and the four

”PoE Out” "PoE (Data and Power) output"ports function as .

Step 1: Connect a standard Cat5e/6 UTP cable from power source

equipment (PSE), such as PoE switch, PoE injector hub and

single port PoE injector, to the port of the Gigabit “PoE IN”

PoE Extender.

Ultra PoE Switch

UTP

PoE

PoE In-Use

PoE MAX

PWR

1234

541 2

PoE OUT PoE IN

10/100

1000

LNK ACT

Step 2: The PSE delivers both Ethernet data and PoE power over UTP

cable to the Gigabit PoE Extender.

Step 3: Once the Gigabit PoE Extender detects the existence of an

IEEE 802.3at/af device, the LED indicator will “PoE-in-Use”

be lit steadily, showing it is providing powerr.

Note

1. If the connected device is not fully complying with IEEE

802.3af/at standard or in-line power device, the PoE-in-

Use LED indicator of the Gigabit PoE Extender will not

be lit steadily.

2. According to IEEE 802.3af/at standard, the Gigabit

PoE Extender will not inject power to the cable if not

connected to a standard IEEE 802.3af/at device.

5.4 PoE Power Distribution

The POE-E304 can obtain a maximum of 60-watt PoE power from Ultra

PoE input port and supplies a maximum of 55-watt PoE power budget

to four PoE output ports, extending both the reach of Gigabit Ethernet

Data Ethernet and IEEE 802.3at/802.3af Power over over the

standard 100m (328 ft.) Cat 5/5e/6 UTP cable to up to 200m at the

same time.

IEEE 802.3at (25W)

PoE PTZ IP Camera

IEEE 802.3af (12W)

PoE Dome IP Camera

Ultra PoE (60W)

1 In 2 Out 1 In 4 Out

6. Power Over Ethernet Budget

The following table lists how many PoE devices can be powered by

POE-E304:

Power Source PoE Output

Budget* Max. Number of PDs supported

IEEE 802.3at PoE+

PSE 25 watts max.

Class 4 PD@25-watt 1 unit

Class 3 PD@15-watt 1 unit

Class 2 PD@7-watt 3 units

PLANET 60W Ultra

PoE PSE 55 watts max.

Class 4 PD@25-watt 2 units

Class 3 PD@15-watt 3 units

Class 2 PD@7-watt 4 units

External Power

Adapter –

56V DC, 65W

55 watts max.

Class 4 PD@25-watt 2 units

Class 3 PD@15-watt 3 units

Class 2 PD@7-watt 4 units

Note

1. The PoE Output Budget means the 4-port PD

aggregated power output. The aggregated power

consumption will be below 55 watts if with ultra PoE

PSE.

2. If the PoE output, whose power source is IEEE

802.3at PoE+, is more than 25 watts, the device will

be shut down.

7. Customer Support

Thank you for purchasing PLANET products. You can browse our online

FAQ resource at PLANET web site rst to check if it could solve your

issue. If you need more support information, please contact PLANET

switch support team.

PLANET online FAQ:

http://www.planet.com.tw/en/support/faq.php?type=1

Switch support team mail address:

support_switch@planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other trademarks

belong to their respective owners

Product specificaties

Merk:	Planet
Categorie:	Wifi-repeater
Model:	POE-E304
Kleur van het product:	Blauw
Gewicht:	403 g
Breedte:	168 mm
Diepte:	93 mm
Hoogte:	32 mm
Soort:	Netwerkzender & -ontvanger
Materiaal behuizing:	Metaal
LED-indicatoren:	Ja
Montagewijze:	Bureau/muur
Aantal Ethernet LAN (RJ-45)-poorten:	5
Vermogensverbruik (max):	60 W
Certificering:	FCC Part 15 Class A, CE
Plug and play:	Ja
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Bekabelingstechnologie:	10/100/1000Base-T(X)
Netwerkstandaard:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt, IEEE 802.3u, IEEE 802.3x
Temperatuur bij opslag:	-10 - 70 °C
Luchtvochtigheid bij opslag:	5 - 95 procent
Power over Ethernet (PoE):	Ja
MAC-adrestabel:	2000 entries
Datastroombeheer:	Ja
Jumbo Frames ondersteuning:	Ja
Maximaal bereik:	100 m
Auto MDIX IEEE:	Ja
Auto-negotiation:	Ja
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Code geharmoniseerd systeem (HS):	85176990
Hoeveelheid Power over Ethernet (PoE) ports:	5
Ondersteundende kabel types:	Cat5, Cat5e, Cat6
Duplex systeem:	Volledig
Aantal RJ-45-poorten (ontvanger):	1
Aantal RJ-45-poorten (zender):	4