Philips Azur Performer GC3819 Handleiding

Philips Strijkijzer Azur Performer GC3819

Lees hieronder de 📖 handleiding in het Nederlandse voor Philips Azur Performer GC3819 (13 pagina's) in de categorie Strijkijzer. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/13

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at

www.philips.com/welcome.

Important

Read this important information carefully before you

use the appliance and save it for future reference.

Danger

- Never immerse the iron in water.

Warning

- Check if the voltage indicated on the appliance

corresponds to the local mains voltage before you

connect the appliance.

- Do not use the appliance if the plug, the mains cord

or the appliance itself shows visible damage, or if the

appliance has been dropped or leaks.

- If the mains cord is damaged, you must have it replaced

by Philips, a service centre authorised by Philips or

similarly qualied persons in order to avoid a hazard.

- Never leave the appliance unattended when it is

connected to the mains.

- Always unplug the appliance from the socket outlet

before you ll the water tank with water.

- This appliance can be used by children aged from

8 years and above and by persons with reduced

physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given

supervision or instruction concerning use of the

appliance in a safe way and if they understand the

hazards involved.

- Do not allow children to play with the appliance.

- Older children are only allowed to clean the

appliance and perform the Calc-Clean procedure

under supervision.

- Keep the iron and its mains cord out of the reach of

children less than 8 years of age when the appliance

is switched on or cooling down.

- Always place and use the iron on a stable, level and

horizontal surface.

- Do not let the mains cord come into contact with

the hot soleplate of the iron.

- Cleaning and user maintenance shall not be made by

children without supervision.

Warning For Iron models with Quick :

Calc Release feature

- Do not open and remove the Quick Calc Release

tray from the appliance during use.

- Only use the Quick Calc Release tray that is supplied

with the appliance. Do not use other tray on the

appliance.

- Do not ll water, perfume, vinegar, starch, descaling

agents, ironing aids or other chemicals at the channel

of the Quick Calc Release tray.

- Do not insert your nger or pointed objects into

the channel of the Quick Calc Release tray.

CAUTION Hot surface : (Fig. 1)

Surfaces are liable to get hot during use (for irons

with ‘hot’ symbol marked on the appliance).

Caution

- Only connect the appliance to an earthed wall socket.

- Check the mains cord regularly for possible damage.

- Fully unwind the mains cord before you plug it in the

wall socket.

- The soleplate of the iron can become extremely hot

and may cause burns if touched.

- Descale the iron regularly according to the

instructions in chapter ‘Cleaning and maintenance’ in

the user manual.

- When you have nished ironing, when you clean the

appliance, when you ll or empty the water tank and

also when you leave the iron even for a short while:

set the steam control to the ‘dry ironing’ position,

put the iron on its heel and remove the mains plug

from the wall socket.

- Do not put perfume, vinegar, starch, descaling agents,

ironing aids or other chemicals in the water tank.

- This appliance is intended for household use only.

Electromagnetic elds (EMF)

This Philips appliance complies with all applicable standards and regulations

regarding exposure to electromagnetic elds.

Environment

- Do not throw away the appliance with the normal household waste at

the end of its life, but hand it in at an ofcial collection point for recycling.

By doing this, you help to preserve the environment (Fig. 2).

Guarantee and support

If you need information or support, please visit www.philips.com/support

or read the separate worldwide guarantee leaet.

Product overview (Fig. 3)

1 Spray nozzle

2 Water lling door

3 Spray button

4 Steam slider

a. Dry setting

b. ECO setting

c. Auto steam setting

5 Steam boost trigger

6 Safety auto-off light

(specic types only)

7 Mains cord

8 Temperature indicator light

9 Water tank

10 Temperature dial with Auto steam

control

11 Calc clean button

12 Typeplate

13 Soleplate

GC3800 series

Specifications are subject to change without notice

4239 000 94381

User manual

Always there to help you

www.philips.com/welcome

Using the appliance

Filling the water tank

Note: Your appliance has been designed to

be used with tap water. If you live in an area

with hard water, fast scale build-up may occur.

Therefore, it is recommended to use 100%

distilled or demineralized water to prolong the

lifetime of your appliance.

1 Open the water lling door.

2 Tilt the iron backwards and ll the water

tank with tap water up to the maximum

level.

Note: Do not ll the water tank beyond the

MAX indication.

Do not put perfume, vinegar, starch,

descaling agents, ironing aids or other

chemicals in the water tank.

3 Close the water lling door (‘click’).

Temperature and steam setting

Table 1:

Warning: Do not use steam or steam boost at

low temperature, as indicated in the below table.

Otherwise, hot water may leak from the iron.

Fabric type Temperature

setting

Auto steam

control

Steam

boost

Linen MAX Automatically

adjusted to

the optimal

amount

Yes

Cotton ●●● Yes

Wool No●●

Silk No●●

Synthetic

fabric (e.g.

acrylic, nylon,

polyamide,

polyester)

●No steam No

1 Consult table 1 to set the temperature

dial to the appropriate setting for your

garment.

2 Select Auto steam setting in the steam

slider.

This iron is equipped with Auto steam

control. According to the temperature you

select, the iron automatically provides the

optimal amount of steam for the best result.

3 Put the iron on its heel and plug it in. The

temperature light goes on to indicate

that the iron is heating up.

4 When the temperature light goes

out, the iron has reached the correct

temperature and you could start ironing.

Features

Spray funtion

- Press the spray button to moisten the

article to be ironed. This helps to remove

stubborn creases.

Steam boost function

- Press and release the steam boost trigger

for a powerful boost of steam to remove

stubborn creases.

Ironing with extra steam

- For extra steam during ironing, press and

hold the steam boost trigger.

Vertical steam

- You can use the steam boost function

when you hold the iron in vertical position

for removing creases form hanging

clothes, curtains etc.

Eco steam setting / Dry ironing

- In stead of Auto steam, you could choose

ECO setting in the steam slider to save

energy, yet to achieve satisfactory ironing

results.

- To iron without steam, select dry setting

in the steam slider.

Safety auto-off (specic types only)

The safety auto-off function automatically switches

off the iron if it has not been used for 30 seconds

resting on its soleplate or 8 minutes resting on its

backplate. The auto-off light will light up.

- To let the iron heat up again, pick up the

iron or move it slightly. The auto-off light

goes out.

Cleaning and maintenance

Cleaning

1 Unplug the iron and let it cool down.

2 Pour any remaining water out of the

water tank from the water lling door.

3 Wipe akes and any other deposit off

the soleplate with a damp cloth and a

non-abrasive (liquid) cleaning agent.

To keep the soleplate smooth, avoid hard

contact with metal objects. Never use a

scouring pad, vinegar or other chemicals to

clean the soleplate.

Calc-clean function

IMPORTANT: Use Calc-clean function every

1 month to prolong the life of your iron. If

water in your area is very hard, or you see scales

coming out from the soleplate during ironing,

use this function more frequently.

1 Make sure the iron is unplugged and the

steam slider is set to dry setting.

2 Fill the water tank to the MAX

indication.

Do not pour vinegar or other descaling

agents into the water tank.

3 Plug in the iron and set the temperature

dial to MAX.

4 Unplug the iron when the temperature

light goes out.

5 Hold the iron over the sink. Keep pushing

the calc clean button and gently shake the

iron forth and back until all water in the

water tank has been used up.

Scales is ushed out, steam and boiling water

also come out of the soleplate.

Note: Repeat steps 2 to 5 if the water that

comes out of the iron still contains scale particles.

6 Plug in the iron and let the iron heat up

to dry the soleplate.

7 Unplug the iron when the temperature

indicator light goes out.

8 Move the iron gently over a piece of

cloth to remove any water stains on the

soleplate.

Storage

1 Unplug the iron and empty the water

tank. Let it cool down in a safe place.

2 Wind the mains cord around the

backplate of the iron and store it on its

heel.

Troubleshooting

This chapter summarises the most common

problems you could encounter with the

appliance. If you are unable to solve the

problem with the information below, visit

www.philips.com/support for a list of

frequently asked questions or contact the

Consumer Care Centre in your country

(see the worldwide guarantee leaet for

contact details).

Problem Possible cause Solution

The steam boost

function does not

work properly

(water leaks out

of the soleplate).

You have used the

steam boost function

too often within a very

short period.

Wait for a few seconds

before you use the steam

boost function again.

You have used the

steam boost function at

a too low temperature.

Set an ironing temperature

at which the steam boost

function can be used

( to MAX).●●●

Flakes and impurities

come out of the

soleplate during

ironing.

Scales are formed inside

the soleplate.

Use the Calc-clean funtion

(see chaper ‘Cleaning and

maintenance’, section

‘Calc-clean function’).

Water leaks from the

water lling door.

You have overlled the

water tank.

Do not ll the water tank

beyond the MAX indication.

Pour excess water out of

the water tank.

Product specificaties

Merk:	Philips
Categorie:	Strijkijzer
Model:	Azur Performer GC3819
Kleur van het product:	Black,Grey,White
Snoerlengte:	2 m
Soort:	Stoomstrijkijzer
Vermogen:	2600 W
Capaciteit watertank:	0.3 l
Zelfreinigend:	Ja
Automatisch antikalksysteem:	Ja
Anti-druppelfunctie:	Ja
Sproeifunctie:	Ja
Continu stoom uitvoering:	45 g/min
Verticale stoomfunctie:	Ja
Zoolplaat materiaal/coating:	SteamGlide-zoolplaat
Steam boost performance:	200 g/min
Stoomstoot functie:	Ja
Draadloos:	Nee