Peerless-AV XHB492-EUK Handleiding

Peerless-AV Monitor XHB492-EUK

Lees hieronder de 📖 handleiding in het Nederlandse voor Peerless-AV XHB492-EUK (28 pagina's) in de categorie Monitor. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/28

12018-08-10 #:180-9120-1

XTREME™ HIGH BRIGHT OUTDOOR DISPLAY

MODEL: XHB432-EUK, XHB492-EUK, XHB552-EUK

User Guide

ENG

22018-08-10 #:180-9120-1

SYSTEM INSTALLATION AND ELECTRICAL REQUIREMENTS

Electrical Code

Note: To the display system installer: This reminder is provided to call attention to Article 820-44 of

the National Electric Code that provides guidelines for proper grounding and, in particular, species

that the cable ground shall be connected to the grounding system of the facility. Outlet shall be

installed near the equipment and shall be easily accessible.

Antenna discharge unit

(NEC Section 810-20)

NEC National Electric Code

Ground clamp

Electric service

equipment

Ground clamps

Power service grounding

electrode system

(NEC Art 250 Part H)

Grounding conductors

(NEC Section 810-21)

Antenna lead-in wire

Note: Installation shall incorporate UL Listed external surge protection rated 2500 Vpk or less, for 150

to 300 Vac mains, installed in accordance with Article 285 of ANSI/NFPA 70 or applicable local codes.

Power Source

The display must be connected to a mains socket outlet with a protective grounding connection.

The mains plug is used as the disconnect device and shall remain readily accessible.

Electrical installation shall be in accordance with the applicable parts of Chapter 8 of ANSI/NFPA70.

An outdoor antenna should not be located near overhead electrical lines or any electrical circuits.

If an outside antenna is connected to the receiver, conrm that the antenna system is grounded to

protect against voltage surges and built up static charges. Section 810 of the National Electric Code,

ANSI/NFPA No 70-1984, provides information with respect to proper grounding for the mast and

supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding

connectors, location of antenna discharge unit, connection to grounding electrodes and requirements

for the grounding electrode.

This display operates on 100-240 volts 50-60 Hz, AC current. Insert the power cord into a 220-240

volt 50 Hz outlet. Never connect the display to direct current or anything other than the specied

voltage.

To prevent electric shock from the display, do not use with an extension cord, receptacle, or other

outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure.

All secondary lines must be routed through grounded conduit and kept separate from AC line.

32018-08-10 #:180-9120-1

Relevant Information

Record your display's model and serial number here for future reference. Keep this user manual in an

accessible location in the event service is required.

Note: Your display's serial number can be found on the box and underneath the rear cover plate.

Model Number ____________________________________

Serial Number ____________________________________

FCC CAUTION

To assure continued compliance and possible undesirable interference, ferrite cores may be used

when connecting this display to video equipment; maintain at least 400mm (15.75 inches) spacing to

other peripheral devices.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rule. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with these instructions,

may cause harmful interference to radio communications; however, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment o

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio/display technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause

undesired operation.

Product specificaties

Merk:	Peerless-AV
Categorie:	Monitor
Model:	XHB492-EUK
Kleur van het product:	Zwart
Gewicht:	41700 g
Breedte:	1136 mm
Diepte:	103 mm
Hoogte:	666 mm
Gewicht verpakking:	50000 g
Breedte verpakking:	1269 mm
Diepte verpakking:	218 mm
Hoogte verpakking:	796 mm
Internationale veiligheidscode (IP):	IP68
Omgevingslichtsensor:	Ja
Beeldschermdiagonaal:	48.5 "
Resolutie:	1920 x 1080 Pixels
Touchscreen:	Nee
Oorspronkelijke beeldverhouding:	16:9
USB-poort:	Ja
Ondersteuning voor plaatsing:	Buiten
Ethernet LAN:	Ja
Ondersteunde video-modi:	480i, 480p, 720p, 1080i, 1080p
Kijkhoek, horizontaal:	178 °
Kijkhoek, verticaal:	178 °
Typische contrastverhouding:	1300:1
Helderheid:	2500 cd/m²
Aantal HDMI-poorten:	3
Componentingang video (YPbPr/YCbCr):	1
DVI-poort:	Nee
Aantal Ethernet LAN (RJ-45)-poorten:	1
Stroomverbruik (in standby):	- W
Aantal USB-aansluitingen:	1
USB-versie:	2.0
Maximale refresh snelheid:	60 Hz
Aansluiting voor netstroomadapter:	Ja
HD type:	Full HD
Display technologie:	LED
Responstijd:	8 ms
Pixel pitch:	5593 x 5593 mm
VESA-montage:	Ja
Paneelmontage-interface:	400 x 200,400 x 400 mm
Bedoeld voor:	Universeel
Bedrijfsuren (uren/dagen):	24/7
On Screen Display (OSD)-talen:	ENG, FRE
Aantal DisplayPorts:	1
VGA (D-Sub) invoer ports:	1
Audio (L,R) out:	1
Geluidsmodi:	Dynamic, Standard, Theater
Ruisonderdrukking:	Ja
Kleurdiepte:	10 Bit
On Screen Display (OSD):	Ja
Aantal On Screen Display-talen:	3
RS-232:	Ja
Instelbare kleurtemperatuur:	Ja
Kleurtemperatuur display:	Cool, Neutral, Warm
Productontwerp:	Digitale signage flatscreen
AC-ingangsspanning:	100 - 240 V
AC-ingangsfrequentie:	50 - 60 Hz
Stroomverbruik (typisch):	196 W
Bedrijfstemperatuur (T-T):	-35 - 60 °C