Peavey SP 4P Handleiding

Peavey Speaker SP 4P

Lees hieronder de 📖 handleiding in het Nederlandse voor Peavey SP 4P (21 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 84 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/21
www.peavey.com
SP®4P
Powered Speaker System
Product
Specications
FCC/ICES Compliancy Statement
This device complies with Part 15 of the FCC rules and Industry Canada license exempt RSS Standard(s). Operation is -
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, that may cause undesired operation.
Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire de
brouillage, et (2) I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the
user’s authority to use the equipment.
Note – This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, , uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
ENGLISH
SP®4P
e Peavey® SP®4P is a powered, bi-amplied, two-way speaker system engineered to provide very high levels of
performance in a compact powered loudspeaker. is quasi-three-way powered system is comprised of a 1000
W peak switching power amplier driving a pair of 15” Black Widow® BWX series woofers, now with a long
throw voice coil. e 2” RX™22CT titanium diaphragm compression driver is driven by a 500 W peak switching
power amplier, and is coupled to a low coloration waveguide with a coverage pattern of 100° horizontal by 50°
vertical.
e SP®4P is capable of up to 131 dB peak SPL. e enclosure is constructed of plywood augmented with internal
braces, covered with a textured black painted nish.e shape is a trapezoidal form, with a full-length coated
perforated steel grille, to oer an attractive yet durable powered speaker system. A pair of four-way inset handles,
one on each side, and a set of casters on the bottom rear edge and a top rear handle provide convenient transport
and handling. Multiple y points are provided to allow overhead rigging.e cabinet and grille are black.
Two independent mixed input channels each oer a balanced input to the preamp/EQ electronics, and a level
control. Each channel has one combo female XLR and 1/4” TRS phone jack. It is switchable between mic-level
and line-level sensitivity. Channel 2 has a 3.5 mm media jack added. A line out section has male XLR connec-
tors. e ru outputs allow linking of additional speaker systems, or feed of the signal to a powered subwoofer,
etc.
e power ampliers providing the bi-amplication are low-distortion switching units providing 1000 W peak
available power into the nominal 4 ohm load of the woofer, and a 500 W peak available power into the nominal 8
ohm load of the tweeter.e power supply for both amps is a switch mode type for low weight and high ecien-
cy. Both ampliers feature our DDT™ compression, which virtually eliminates audible power amplier clipping.
Cooling is via forced air circulation.
e combination of the Black Widow® BWX woofer with the RX™22CT tweeter and DSP crossover and EQ pro-
vide a clarity and impact beyond conventional powered enclosures. e switching power amps and switch-mode
power supply, along with the professional grade speaker components, provide this high level of technological
sophistication at a very light weight, while at a very reasonable cost.
* BI-AMPLIFIED POWERED SPEAKER SYSTEM
* 1000 WATTS PEAK AVAILABLE WOOFER POWER, 500 WATTS PEAK AVAILABLE TWEETER POWER
* BOTH POWER AMPS HAVE DDT COMPRESSION
* TWO 15” BLACK WIDOW® BWX WOOFERS
* PEAVEY RX™22CT COMPRESSION DRIVER TWEETER ON A QUADRATIC THROAT WAVEGUIDE
* PEAK SPL UP TO 131 DB WITH MUSIC!
* DSP BASED CROSSOVER, LIMITING AND EQ
* EQ PRESETS AVAILABLE VIA ROTARY ENCODER PUSHBUTTON SELECT
* 9-BAND EQ AND OTHER SYSTEM SETTINGS ACCESSED VIA ROTARY ENCODER PUSHBUTTON SELECT
* DYNAMIC BASS BOOST FUNCTION
* UP TO 150 MS OF ARCHITECTURAL DELAY
* FAN COOLED FOR MAXIMUM RELIABILITY
* TWO INDEPENDENT MIXED INPUT CHANNELS, WITH GAIN CONTROL AND MIC/LINE GAIN SWITCH


Product specificaties

Merk: Peavey
Categorie: Speaker
Model: SP 4P

Heb je hulp nodig?

Als je hulp nodig hebt met Peavey SP 4P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Peavey

Handleiding Speaker

Nieuwste handleidingen voor Speaker