Peavey iSPD PRO Handleiding

Peavey Niet gecategoriseerd iSPD PRO

Lees hieronder de 📖 handleiding in het Nederlandse voor Peavey iSPD PRO (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 66 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/12
www.peavey.com
iSPD PRO
Intelligent Sequential Power
Distribution System
Operating
Manual
2
FCC/ICES Compliancy Statement
This device complies with Part 15 of the FCC rules and Industry Canada license exempt RSS Standard(s). Operation is -
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, that may cause undesired operation.
Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’appareil ne doit pas produire de
brouillage, et (2) I’utilisateur de I’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Warning: Changes or modifications to the equipment not approved by Peavey Electronics Corp. can void the
user’s authority to use the equipment.
Note – This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, , uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures.
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
3
iSPD PRO
Intelligent Sequential Power Distribution
The iSPD Pro is a programmable power sequencer with many applications in the audio/Video industry. Each
of its 8 power outlets is individually controlled and its delay time can be individually set. Any of the 8 outputs
can also be configured for constant on as well. When your requirements call for more than one unit, up to 8
iSPD Pro sequencers can be inter-connected via an RS 485 interface requiring only with a simple twisted pair.
The units can be configured and monitored over Ethernet using the management software provided.
There are several reasons to use a power sequencer to turn on system equipment. When powering on sound
system equipment, it is always a good idea to power on low level equipment like mixers and signal processor
first allowing them to stabilize before energizing the power amplifiers. This helps prevent unintended pops
and noises from being amplified and sent to the loud speakers. Most electronic equipment requires a surge of
power from the power line when it is first turned on. This is a even bigger issue for high power devices like
power amplifiers. By sequencing the turn-on of equipment, the instantaneous power demand can be greatly
reduced.
ENGLISH
Features
• 8 output channels with individually adjustable delay time.
• Front panel or remote power sequence control.
• Additional units may be linked for expanded capacity.
• Control Graphical interface program for custom configuration and monitoring over Ethernet.
Front Panel
2 3
(1) Line Voltage display.
The current line voltage is displayed. Make sure that the line voltage is correct before activating the switch to
turn on the connected equipment.
(2) Sequence Controller Display
The status of each of the 8 outputs is shown in this display. The LEDs illuminate when their corresponding
outlet circuit is energized. The Status LED is illuminated when the iSPD is connected to a power source.
(3) Key Switch
When the front panel key switch is turned to the on position, the power up sequence is initiated energizing
outputs 1 to 8 in order. Returning the switch to the standby position reverses the sequence, turning off
the output circuits from 8 to 1. This same control function can be initiated by using a customer supplied
switch connected to terminals on the rear of the unit. For more information on its operation, see the section
describing remote switch control.

Product specificaties

Merk: Peavey
Categorie: Niet gecategoriseerd
Model: iSPD PRO

Heb je hulp nodig?

Als je hulp nodig hebt met Peavey iSPD PRO stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Peavey

Peavey

Peavey PV 16DR Handleiding

2 November 2024
Peavey

Peavey AQ12 Handleiding

27 Mei 2024
Peavey

Peavey Automatch II Handleiding

13 Maart 2024
Peavey

Peavey PV 1 Handleiding

11 Maart 2024
Peavey

Peavey iSPD PRO Handleiding

5 Januari 2024
Peavey

Peavey Dual DeltaFex Handleiding

5 Januari 2024
Peavey

Peavey MAX 112 Handleiding

29 November 2023
Peavey

Peavey Nashville 1000 Handleiding

29 November 2023
Peavey

Peavey Impulse 12D Handleiding

29 November 2023
Peavey

Peavey Sanctuary SSE 6 Handleiding

29 November 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

D-Link

D-Link DWL-650 Handleiding

23 December 2024
D-Link

D-Link Air Xpert DWL-AG520 Handleiding

23 December 2024
D-Link

D-Link DGS-1008T Handleiding

23 December 2024
MSW

MSW -LRL2T-2 Handleiding

23 December 2024
Hamlet

Hamlet XPDC-G3018Q Handleiding

23 December 2024
Philips

Philips Avent Soothie SCF099 Handleiding

23 December 2024
Philips

Philips Avent SCF075 Handleiding

23 December 2024
Philips

Philips DreamWear HH1111 Handleiding

23 December 2024
Philips

Philips BS9B1617TB Handleiding

23 December 2024
Philips

Philips 32BDL5150I Handleiding

23 December 2024