Peavey CS 6000 Handleiding

Peavey Receiver CS 6000

Lees hieronder de 📖 handleiding in het Nederlandse voor Peavey CS 6000 (14 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/14
www.peavey.com
CS® 6000 and CS® 4000
Power Ampliers
Operating
Manual
2
CS® 6000 and CS® 4000
Power Amplifier
Congratulations on your purchase of the CS 6000/ CS 4000, a power amplifier designed for years of reliable, flawless operation under
rigorous use. This amplifier offers the sonic superiority and unsurpassed reliability for which Peavey is famous, while remaining sur-
prisingly compact. Advanced technology and extensive protection circuitry allow operation with greater efficiency into difficult loads
and power conditions. The DDTâ„¢ (Distortion Detection Technique) circuitry ensures trouble-free operation into loads as low as 2
ohms. DDT protects drivers and ensures that sonic integrity is maintained, even in extreme overload conditions. The CS's high-effi-
ciency design uses multi-rail class-H technology to produce high output power while reducing losses. Massive heat-sinks and a high
volume cooling fan maintains a lower overall operating temperature, resulting in longer output transistor life. For your safety, read
the important precautions section, as well as input, output and power connection instructions.
Although the CS 6000 amplifier is simple to operate and housed in an ultra-strong steel chassis, improper use can be dangerous.
This amplifier is very highpowered and can put out high voltages and sizable currents at frequencies up to 30 kHz. Always use safe
operating techniques when operating this amplifier.
Before you send signal through your amplifier, it is very important to ensure that the product has the proper AC line voltage
supplied. You can find the proper voltage for your amp printed next to the IEC line (power) cord on the rear panel of the
unit. Each product feature is numbered. Refer to the front panel diagram in this manual to locate the particular features next
to its number.
Please read this guide carefully to ensure your personal safety as well as the safety of your amplifier.
FEATURES:
• Distortion Detection Technique (DDT)
• Line voltage selector switch
• High volume cooling fan
• 100 Hz, 24dB/octave, Linkwitz-Riley Crossover
• Front panel LEDs: DDT, Signal,Thermal Protect and Power
• Switchable 2nd order 40Hz high pass filter
ENGLISH
3
SAVE THESE INSTRUCTIONS
1 Save the carton and packing materials!
Should you ever need to ship the unit,
use only the original factory packing.
For replacement packaging, call Peavey
Customer Service Department directly.
2 Read all documentation before operat-
ing your equipment. Retain all docu-
mentation for future reference.
3 Follow all instructions printed on
unit chassis for proper operation.
4 Never hold a power switch or circuit
breaker in the "ON" position if it
won’t stay there by itself!
5 Do not use the unit if the electrical
power cord is frayed or broken.
The power supply cords should be
routed so that they are not likely to
be walked on or pinched by items
placed upon or against them.
6 Always operate the unit with the AC
ground wire connected to the electri-
cal system ground. Precautions should
be taken so that the means of ground-
ing of a piece of equipment is not
defeated.
7 Damage caused by connection to
improper AC voltage is not covered by
any warranty. Mains voltage must be
correct and the same as that printed on
the rear of the unit.
8 Do not ground any hot (red) terminal.
Never connect a hot (red) output to ground
or to another hot (red) output!
9 Power down and disconnect units from
mains voltage before making connec-
tions.
10 Do not drive the inputs with a signal
level greater than that required to
enable equipment to reach full out-
put.
11 Do not run the output of any amplifier
channel back into another channel’s
input.
Do not parallel- or series-connect
an amplifier output with any other
amplifier output.
Peavey is not responsible for damage
to loudspeakers for any reason.
12 Do not connect the inputs or out-
puts of amplifiers to any other volt-
age source such as a battery, mains
source, or power supply, regardless
of whether the amplifier is turned
on or off.
13 Connecting amplifier outputs to oscil-
loscopes or other test equipment while
the amplifier is in bridged mono mode
may damage both the amplifier and test
equipment!
14 Do not spill water or other liquids
into or on the unit, or operate the unit
while standing in liquid.
15 Do not block fan intake or exhaust
ports.
Do not operate equipment on a sur-
face or in an environment which
may impede the normal flow of air
around the unit, such as a bed, rug,
weathersheet, carpet or completely
enclosed rack.
16 If the unit is used in an extremely
dusty or smoky environment the
unit should be periodically blown
free of foreign matter.
17 Do not use the unit near stoves,
heat registers, radiators or other
heat-producing devices.
18 The equipment power cord should be
unplugged from the outlet when left
unused for a long period of time.
Service Information
Do not remove the cover!
Removing the cover will expose you
to potentially dangerous voltages.
There are no user-serviceable parts
inside.
Equipment should be serviced by
qualified service personnel when:
A. The power supply cord or the plug has
been damaged.
B. The equipment has been exposed to
rain.
C. The equipment does not appear to
operate normally or exhibits a marked
change in performance.
D. The equipment has been dropped or
the enclosure damaged.
To obtain service:
contact your nearest Peavey Service
Center, Distributor, Dealer or con-
tact Peavey at 601.483.5365 USA or
visit www.peavey.com for additional
information, email techserve@peavey.
com


Product specificaties

Merk: Peavey
Categorie: Receiver
Model: CS 6000

Heb je hulp nodig?

Als je hulp nodig hebt met Peavey CS 6000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Peavey

Handleiding Receiver

Nieuwste handleidingen voor Receiver