PCE Instruments PCE-RE100P Handleiding

PCE Instruments Controller PCE-RE100P

Lees hieronder de 📖 handleiding in het Nederlandse voor PCE Instruments PCE-RE100P (10 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/10
PCE-RE100P-EN-03-190211 1/10
PCE-RE100P Series Programmable Profile Controller
Thank you for choosing series programmable profile controller. PCE-RE100P
* 96x96mm sized.
* 3,5 inches TFT , graphic and 5 digit display.
* Selectable TC, RTD, NTC, R, mA, V or mV inputs.
* Input offset feature
* 32 point linearization for analog inputs.
* Selectable relay, SSR or analog outputs.
* Selectable , input proportional transmitter output(mA or V).
* 50ms sampling time.
* PID control.
* PID selftune.
* PID auto-tune.
Selftune automatic PID calculation or
manually enter PID parameters if known.
* Soft-Start feature.
* 24Vdc for sensor supply.
* 16 program and 8 step for profile control.
* Selectable Single Setpoint Mode or Profile Control Mode.
* Digital inputs for profile control.
* Security levels for menu and configuration pages.
* RS485 ModBus protocol communication feature.(optional)
* CE marked according to Europen Norms.
.
* In case of sensor failure manually , periodical or auto-periodical
control can be selected.
Analog Inputs
DIGITAL INPUTS (In order to use for profile control process)
OUTPUTS
ENVIRONMENTAL CONDITIONS
ELECTRICAL CHARACTERISTICS
HOUSING
Input Type
200,0 ... 1800,0 C°
-100,0 ..... 900,0 C°
-100,0 ..... 900,0 C°
-100,0 ... 1300,0 C°
-100,0 ..... 900,0 C°
-200,0 ... 1300,0 C°
0,0 ... 1700,0 C°
0,0 ... 1700,0 C°
-250,0 ..... 300,0 C°
-200,0 ..... 400,0 C°
-200,0 ..... 850,0 C°
-100,00 ... 160,00°C
-60,0 ..... 150,0 C°
5V or 30V pulse , Ri=100kΩ
% 0.1 or 2 C (3,6 F)± ± ° °
% 0.1 or 0,5 C (1 F)± ± ° °
Accuracy
+ undefined
+ purple
+ black
+ green
+ red
+ lilac
+ orange
+ orange
+ brown
+ red
Sensor current 250 Aµ
Cable ColorInput Resist.
- white
- white
- white
- white
- blue
- white
- white
- white
- white
- brown
% 0.1 or 0,5 C (1 F)± ± ° °
% 0.1 or 0,5 C (1 F)± ± ° °
% 0.1 or 0,5 C (1 F)± ± ° °
% 0.1 or 0,5 C (1 F)± ± ° °
% 0.1 or 0,5 C (1 F)± ± ° °
% 0.1 or 0,5 C (1 F)± ± ° °
% 0.1 or 0,5 C (1 F)± ± ° °
% 0.1 or 1 C (1.8 F)± ± ° °
% 0.1 or 1 C (1.8 F)± ± ° °
% 0.1 or 1 digit± ±
% 0.1 or 1 digit± ±
% 0.1 or 1.5 C (2.7 F)± ± ° °
Range
392,0 ... 3272,0 F°
-148,0 ... 1652,0 F°
-148,0 ... 1652,0 F°
-148,0 ... 2372,0 F°
-148,0 ... 1652,0 F°
-328,0 ... 2372,0 F°
32,0 ... 3092,0 F°
32,0 ... 3092,0 F°
-418,0 ..... 572,0 F°
-328,0 ..... 752,0 F°
-328,0 ... 1562,0 F°
-148,00 .. 320,00°F
-76,0 ..... 302,0 F°
RTD
NTC
V
mA
mV
Ω% 0.5 or 10± ± Ω
B (Pt30Rh-Pt6Rh)
E (NiCr-Con)
J (Fe-Con)
K (NiCr-Ni)
L (Fe-Con)
N (NiCrSi-NiSi)
R (Pt13Rh-Pt)
S (Pt10Rh-Pt)
T (Cu-Con)
U (Cu-Con)
Pt100
NTC
0 - 20mA
4 - 20mA
0 - 150mV
0 - 5V
1 - 5V
0 - 10V
0 - 550
0 - 10k
Ω
Ω
Control / Alarm 3
Alarm 1
Alarm 2
SSR
mA
V
Ambient/storage temp.
Max. Relative humidity
Rated pollution degree
Height
Supply
Power consumption
Wiring
EMC
Safety requirements
Housing type
Dimensions
Weight
Enclosure material
TC
Ri 50=Ω
Sensor current 250 Aµ
EN 60751
Standart
% 0.1 or 20 V± ± µ
% 0.2 or 0.1± ± Ω
EN 60584
EN 60584
DIN43710
DIN43710
250V AC, 2A . Selectable as NO+NC.10.000.000 switch without load and 200.000 switch under 250V AC 2A (resistive load)
250V AC, 2A . Selectable as NO+NC.10.000.000 switch without load and 200.000 switch under 250V AC 2A (resistive load)
250V AC, 2A . Selectable as NO.10.000.000 switch without load and 200.000 switch under 250V AC 2A (resistive load)
Max. 40mA , 0 - 12Volt , short-circuit protection.
0 - 20mA or 4 - 20mA , Max. load resistance is 750 .
Max. 30mA , 0 - 10Volt , short-circuit protection.
Ω
Ri 100k>Ω
Ri 100k>Ω
Ri 100k>Ω
Ri 100k>Ω
Ri 100k>Ω
Ri 100k>Ω
-32768 ... 32767
-3276,8 ... 3276,7
-327,68 ... 327,67
-32,768 ... 32,767
Do not use the device in locations subject to corrosive and flammable gases.
0 ... +50°C/-25 ... 70°C
Suitable for flush-panel mounting.
Relative humidity 80% for temperatures up to .31°C °C , decreasing linearly to 50% relative humidity at 40
G96xY96xD81mm
According to Front panel Rear EN 60529 : IP65 ,
panel : IP20
Approx. 400g.
Max. 2000m
Self extinguishing plastics.
While cleaning the device , solvents(thinner,gasoline,acid etc.) or corrosive materials must not be used.
2 0V AC, 50/60Hz90- 5
Max. 7 VA
2.5mm² screw-terminal
EN 61326-1: 201 3
EN 61010-1: 201 (0 Pollution degree 2 , overvoltage category ||)
°C
1230.6
1200.0
SV
SSR
A2
A1
A3
0%
Prog.No: Seg.No: 1 1
Prog.Remaining Time(min): 1:0
°C
PRESS SET TO START PROFILE CONTROLLER
PV
Read this document carefully before using this device. The guarantee will be expired by device damages if you don’t attend to the directions
in the user manual. Also we don't accept any compensations for personal injury, material damage or capital disadvantages.
TM
Start-Stop Input
Previous Program Input
Next Program Input
Pause-Resume Input
200
175
150
125
100
75
50
25
0
PV-SV
min
2 4 6 8 10 12 14 16
Program 1 is running
PCE-RE-100P
PCE-RE-100P
PCE Teknik Cihazlar Paz. Tic. Ltd.Şti.
Halkalı Merkez Mah. Pehlivan Sok. No 6/C
34303 Küçükçekmece/ İstanbul
Türkiye
96mm
96mm
6mm 69mm 15mm
PANEL CUT-OUT
92mm
92mm
DIMENSIONS
Not :
1) Panel thickness should be maximum 7mm.
2) If there is no 60mm free space at the back
side of the device , it would be difficult to remove it from
panel.
Flush mounting clamp
For removing the device from panel :
- While pressing both flush mounting clamps of the device
in direction pull it in direction 1 , 2.
1
1
2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 29
17 30
18 31
19 32
20 33
21
22
23
24
25
26
27
28
34
35
36
37
38
39
40
41
42
43
Control
Alarm 3
Valve On
Alarm 1
Alarm 2
Valve Off
90 - 230V AC
50/60Hz, MAX. 7VA
+
+
--
+24V DC (max. 30mA)
GND1
+12V DC (max. 30mA)
RTD
NTC
R
COM
A
ModBus
RS 485 B
{
V OUT
mA OUT
SSR OUT
Previous Program Input
Pause - Resume Input
Start - Stop Input
Next Program Input
+12V
GND
TCmA/mV/V
-
++
-
-
+
PCE-RE100P is intended for installation in control panels. Make sure that the device is used only for intended purpose. The electrical connections
must carried out by a qualified staff and must be according to the relevant locally applicable regulations. During an installation , all of the cables that
are connected to the device must be free of electrical power. The device must be protected against inadmissible humidity , vibrations , severe soiling
and make sure that the operation temperature is not exceeded. The cables should not be close to the power cables or components.
CONNECTION DIAGRAM
Logic output of the instrument is not electrically insulated from the
internal circuits. Therefore , when using grounding thermocouple , do
not connect the logic output terminals to the ground.
1) Main supply cords shall meet the requirements of IEC 60227 or
IEC60245.
2)In accordance with safety regulations,the power supply switch shall
bring the identification of the relevant instrument and it should be easily
accessible by the operator.
Not :
Holding screw
0.4-0.5Nm
Equipment is protected throughout
by DOUBLE INSULATION.
90-250V AC
50/60Hz
MAX. 7VA
90-230V AC
50/60Hz
MAX. 7VA
Switch
Cable size: 1,5mm²
F 100 mA 250V AC
Neutral
Line
SUPPLY VOLTAGE
Fuse should be
connected.
1
2
°C
1230.6
1200.0
SV
SSR
A2
A1
A3
0%
Prog.No: Seg.No:
1 1
Prog.Remaining Time(min):
1:0
°C
PRESS SET TO START PROFILE CONTROLLER
PV
/2 10 PCE-RE100P-EN-03-190211
116
19
29
217
20
30
3
18
21
31
34
4
22
32
35
5
23
33
6
24
25
26
27
28
37
36
10
7
38
11
8
39
12
9
40
41
42
43
13
14
15
116
19
29
217
20
30
3
18
21
31
34
4
22
32
35
5
23
33
6
24
25
26
27
28
37
36
10
7
38
11
8
39
12
9
40
41
42
43
13
14
15
PCE-RE-100P
PCE Teknik Cihazlar Paz. Tic. Ltd.Şti.
Halkalı Merkez Mah. Pehlivan Sok. No 6/C
34303 Küçükçekmece/ İstanbul
Türkiye
Process Value
Set Value
Ouput/ Alarm Relay and SSR status.
(If output is active,related led turns to green.)
Unit
Program Number
Segment Number
Remaining time in min.
% Output ratio
Message box
Decrease Key
Increase Key
Input Key
Back Key
°C
123.4
200.0
SV
SSR
A2
A1
A3
0%
Prog.No: Seg.No:
1 1
Prog.Remaining Time(min):
1:0
°C
PRESS SET TO START PROFILE CONTROLLER
PV
SET Key
HOME SCREEN
°C
123.4
200.0
SV
SSR
A2
A1
A3
0%
°C
SINGLE SET POINT MODE IS RUNNING
PV
°C
°C
°C
123.4
200.0 123.4
200.1 123.4
200.0
SV
SV
SV
SSR
SSR
SSR
A2 A2 A2
A1 A1 A1
A3 A3 A3
0% 0% 0%
°C
°C
°C
SINGLE SET POINT MODE IS RUNNING SINGLE SET POINT MODE IS RUNNING SINGLE SET POINT MODE IS RUNNING
PV
PV
PV
/3 10 PCE-RE100P-EN-03-190211
SET Key : Start/Stop profile controller in “Profile Controller Mode”, Select/Unselect parameter for increase/decrease parameter value in “Programming Mode”.
Change SV in “Single Setpoint Mode”.
Back Key : Return previous page in “Programming Mode”.
Enter Key : Enter main menu and open sub pages and transition between sub pages in “Programming Mode”.
Pause/Resume profile controller in “Profile Controller Mode”.
Increase Key : Transition between parameters (when parameter background is red)
and increase selected parameter value (when parameter background is green) in “Programming Mode”.
Decrease Key :
NOTE 1 : Device must be in “Profile Control Mode” in order to start/stop profile control by pressing Set Key.
NOTE 2 : Prog.No , Seg.No ve Prog.Remaning Time(min)When device in “Single Setpoint Mode”, informations are not shown on home screen.
NOTE 3 : If Increase Key is held down while the device is powered up , factory parameters will be restored.
NOTE 4 : “Single Setpoint Mode” can be selected under “Profile Controller Configuration Page” sub menu , device make a control related to SV ,
which can be adjusted on home screen in “Single Setpoint Mode”.
If Set Key pressed once , SV’s color will be green. In this case SV is adjusted by pressing Increase/Decrease keys.
If Set Key pressed again or by waiting 3 seconds , SV’s color will be white on home screen.
Adjusting Device Set Value in Single Setpoint Mode
Transition between parameters (when parameter background is red)
and decrease selected parameter value (when parameter background is green) in “Programming Mode”.
°C
°C
23.4
50.0 23.4
50.0
SV
SV
SSR
SSR
A2 A2
A1 A1
A3 A3
0% 33%
Prog.No: Seg.No:
0 0 Prog.No: Seg.No: 1 1
Prog.Remaining Time(min):
0:0 Prog.Remaining Time(min):
14:59
°C
°C
PRESS SET KEY TO START PROFILE CONTROL PROFILE CONTROL IS RUNNING
PV
PV
Profile control is stopped by
pressing Set Key and “PROFILE
CONTROLLER IS STOPPED”
message is given for 3 seconds
and device is turned back to
home screen.
200
200200
175
175175
150
150150
125
125125
100
100100
75
7575
50
5050
25
2525
0
00
PV-SV
PV-SVPV-SV
min
minmin
2
22
4
44
6
66
8
88
10
1010
12
1212
14
1414
16
1616
Program 1 is running
Program 1 is running Profil control is finished.
Profile control
program graph
is shown
by pressing
Back Key.
°C
23.4
50.0
SV
SSR
A2
A1
A3
33%
Prog.No: Seg.No: 1 1
Prog.Remaining Time(min):
14:59
°C
PROFILE CONTROLLER IS STOPPED
PV
PV is sampled and saved
once in every minute and
shown on program graph.
Profile Control Mode
Profile control
is started by
pressing
Set Key.
Last saved program
graph can be shown
by pressing Back Key.
PCE-RE-100P

Product specificaties

Merk: PCE Instruments
Categorie: Controller
Model: PCE-RE100P

Heb je hulp nodig?

Als je hulp nodig hebt met PCE Instruments PCE-RE100P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Controller PCE Instruments

PCE Instruments

PCE Instruments PCE-RE21R Handleiding

16 Oktober 2024
PCE Instruments

PCE Instruments PCE-RE100P Handleiding

16 Oktober 2024

Handleiding Controller

Nieuwste handleidingen voor Controller

Speed-Link

Speed-Link Thunderstrike Handleiding

2 December 2024
COLBOR

COLBOR CTRL1 Handleiding

29 November 2024
Gioteck

Gioteck FR-1 (PS3) Handleiding

25 November 2024
Gioteck

Gioteck GC-1 (PS3) Handleiding

25 November 2024
Gioteck

Gioteck HF-2 (PS3) Handleiding

25 November 2024
Gioteck

Gioteck SC-1 (PS3) Handleiding

25 November 2024
Gioteck

Gioteck GC-2 (PS3) Handleiding

25 November 2024
Gioteck

Gioteck HF-1 (PS3) Handleiding

25 November 2024
Gioteck

Gioteck VX-1 (PS3) Handleiding

25 November 2024
Gioteck

Gioteck GC-2 Handleiding

25 November 2024