Panduit TGJT Handleiding

Panduit Niet gecategoriseerd TGJT

Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit TGJT (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

FIGURE 1:

1. Operator should manually

wire the required TG style

Jack Wire Cap for the desired

application. Wires must be

separated and slightly down

over the individual pocket

divider wedges. Depress

strain relief collar to secure

cable.

MADE IN COSTA RICA

TGJT PA25217A01

Rev. 03 2-2016

OPERATING INSTRUCTIONS

Page: 1 of 2

FIGURE 2:

2. Insert the prepared Wire Cap

into the Wire Seating/Cutting

side of the TGJT Tool. This

side pocket properly aligns

and holds the prepared Wire

Cap in place. Make sure all

twisted pairs of wires are out

to the sides of the Wire Cap

for proper cutting (refer to

Figure 1). The ramp of the

Wire Cap must be pointing

upward and be inserted

into the groove in the upper

Cutter Blade Anvil.

FIGURE 3:

3. Pull the handle and the mechanism seats the conductors into

the Wire Cap. At the same time, the Cutter Blades trim the

wires nearly flush with the side faces of the Wire Cap.

4. Keeping the handles closed, slide the Wire Cap up and out of

the tool. All wires should cut cleanly.

www.panduit.com

Technical Support: Panduit USA

888-506-5400, Ext. 86914

E-mail: techsupport@panduit.com

NOTE: STRIPPED WIRES MUST BE LONG ENOUGH TO

STICK OUT OF THE SIDES OF THE WIRE CAP.

Refer to product installation instructions listed above

for recommended wire strip lengths.

RAMP

ANVIL GROOVE

NOTE: IF THE WIRES DO NOT CUT CLEANLY OR THE WIRE

CAP DOES NOT WANT TO COME OUT, EXAMINE THE

CUTTER BLADE EDGE SURFACES AT THE NEXT

OPENING CYCLE. IF BLADES ARE NICKED OR

APPEAR WORN, REPLACE THEM WITH THE BLADE

REPLACEMENT KIT.

TGJT TOOL

DIVIDER

WEDGES

Refer to product installation instructions for

TX6 PLUS and TX5e UTP Jack Modules: PN403M

and TX6A 10Gig UTP Jack Modules: PN511E

for wiring instructions.

STRAIN

RELIEF

COLLAR

TG STYLE JACK TERMINATION TOOL

FOR INSTALLING ALL

TG STYLE COPPER JACK MODULES

Part No.: TGJT

Page: 2 of 2

OPERATING INSTRUCTIONS

FIGURE 4:

5. Keeping the handles closed,

turn the tool over above a

waste wire receptacle or

other scrap container.

Holding the Rear Handle,

release the Trigger Handle.

All scrap cut wires should

drop free from the tool.

FIGURE 5:

6. Place the Wire Cap into the

required Jack Module.

7. Place the Wire Cap / Jack

Module assembly into the

Jack Seating side of the TGJT

Tool (opposite the Wire

Seating/Cutting side).

NOTE: IF WIRES DO NOT EJECT, MAKE SURE WIRE

RETAINERS COME IN CONTACT WITH THE BLADE

ANVILS DURING THE NEXT EMPTY HAND CYCLE. IF

NOT, THEY MAY NEED TO BE BENT SLIGHTLY INWARD.

FIGURE 7:

9. Pull the handle completely

closed until it stops. The Cam

Block Housing Ram will seat

the Wire Cap into the Jack

Module completing the

termination process. An

audible “snap” should be

heard during the seating

process.

10. Holding the Rear Handle,

release the Trigger Handle.

Pull the completed TG Jack

Module Assembly from the

tool.

NOTE: USING THE INCORRECT SETTING OF THE CAM BLOCK

HOUSING RAM CAN RESULT IN EITHER:

1.) A NON-FULLY SEATED WIRE CAP IN THE JACK

MODULE, OR

2.) DAMAGE TO THE TOOL IN THE JACK SEATING AREA OR

DAMAGE TO THE SHUTTER OF THE JACK MODULE IN

SHUTTERED JACKS

FIGURE 8:

11. Inspect the Jack Module

Assembly to make sure the

Wire Cap was fully seated

into the Jack Module. The

Retaining Finger should

have dropped into place

behind the Wire Cap ramp.

NOTE: JACK MODULE RETAINING FINGER MUST BE

ORIENTED TO ALIGN WITH RAMP AND POCKET OF

WIRE CAP.

RAMP

RETAINING FINGER

FIGURE 6:

8. Prior to the handle

operation, the Cam Block

Housing Ram must be

rotated to match the type of

Jack Module being used.

For all standard jack modules

being used, the Cam Block

Housing Ram oval opening

must be rotated to horizontal

(parallel with the backbone of

the tool).

If an older CJD-series

shuttered jack module is being

used (does not indlude the

newer CJH-series shuttered),

the Cam Block Housing Ram

oval opening must be rotated

to vertical.

REPLACEMENT KITS AVAILABLE

(Sold Separately)

KTGJTGRD – Protector Plate Kit

KTGJTBNA – Blade/Anvil Replacement Kit

KTGJTBLD – Blade Replacement Kit

POCKET

HORIZONTAL – STANDARD

VERTICAL – CJD SERIES SHUTTERED

RAMP

SNAP!

RETAINING FINGER DOWN

Product specificaties

Merk:	Panduit
Categorie:	Niet gecategoriseerd
Model:	TGJT
Kleur van het product:	Zwart
Soort:	Combinatiegereedschap
Type verpakking:	Doos
Aantal per verpakking:	1 stuk(s)
Aansluiting(en):	TG
Afmetingen (B x D x H):	146 x 40.2 x 129.9 mm