Panduit PRV679 Handleiding

Panduit Niet gecategoriseerd PRV679

Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit PRV679 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

INSTALLATION INSTRUCTIONS CM293K

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

DUAL HINGED SINGLE HINGED

Single Sided Dual Sided DOORS DOORS

PRV15 PRVF15 PRD15

PRV12 PRVF12 PRD12 PRSHD12

PRV10 PRVF10 PRD10

PRV8 PRVF8 PRD8 PRSHD8

PRV6 PRVF6 PRD6 PRSHD6

All PatchRunner Managers and Dual Hinged Doors are available in 96" tall versions

6 inch and 12 inch wide PatchRunner Managers and Dual Hinged Doors are also available in

(PRV**96, PRVF**96, and PRD**96) **= 6,8,10,12,or 15 inch wide

VERTICAL CABLE MANAGEMENT

79" tall versions (PRV679, PRVF679, PRD679, PRV1279, PRVF1279, PRV1279)

Recommended bolt placement for mounting

manager to rack channel.

Middle Location

Bolt

(For Front Only Manager

& Front & Rear Manager)

Top Location

Bolt

(For Front Only & Front & Rear

Manager)

Bottom Location

Bolt and Spacer

(For Front Only Manager)

Bolt

(For Front & Rear Manager)

(1) P R ATCH UNNER Vertical Cable Manager

(6) 1/2-13 Hex Nuts

(6) 1/2-13x2.0” Bolts

(12) Washers for 1/2-13 bolts

(4) Spools

(2) .91 long 1/2-13 Bolt Spacers

* Spools sold separately for PRV6 & PRVF6

Page 1 of 4

P R ATCH UNNER Vertical Cable Manager

LOCATION GUIDE - STANDARD EIA RACK

CONTENTS

After the first rack is mounted to the floor with the

appropriate hardware, Use Three 1/2-13x2.0” bolts

(supplied with the vertical cable manager panels) to

fasten the PATCHRUNNER Vertical Cable Manager

to the rack. Next, mount the second rack to the

other side of the PATCHRUNNER Vertical Cable

Manager using the remaining 1/2-13x2.0” bolts. Then

mount the second rack to the floor using the appropriate

hardware.

Center Mounting of a P RATCH UNNER on Standard EIA Rack

Spacer

Note:

Tighten bolts to 120 lbs.-in.

Signifies Bottom

6” Vertical Manager dimension shown in brackets [...]

8” Vertical Manager dimensions shown in parenthesis (...)

10” Vertical Manager dimensions shown in asterisk *...*

15 “Vertical Manager dimensions shown in brackets {...}

PART NUMBERS

INSTALLATION INSTRUCTIONS CM293K

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 2 of 4

INSTALLATION OF SPOOLS

Step 1

Align buttons with mounting leg slot

Mounting Face

Step 2

Push buttons through backbone until

mounting face is flush with backbone.

Step 3

Apply downward pressure until plastic

spool clicks into place.

Removal/Replacement

Step 4

Pull back on angled flange while apply-

ing upward pressure

Step 5

Repeat steps 1-3

Angled Flange

Mounting Leg Slots

DUAL HINGED DOOR BRACKET INSTALLATION

Attach cross braces with #10-32 screws to door bracket as shown in

picture below. Align angled notch on cross brace with angled notch

on door bracket when tightening screws.

(4) Screws

Cross Brace

Door Bracket Angled Notches

FINGER REMOVAL

Apply inward pressure at finger ends to remove finger

Score Groove

INSTALLATION INSTRUCTIONS CM293K

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Page 3 of 4

DUAL HINGED DOOR INSTALLATION

Align lower pins with lower hinge pin mounting holes. Squeeze

release knobs together, then align upper door pins with upper hinge

pin mounting holes. Release pressure on the release knobs to set

door in place.

Release Knobs

Door

Upper Door Pin

Upper Hinge Pin Mounting Hole

Lower

Hinge Pin

Mounting Hole

Lower Door Pin

SINGLE HINGED DOOR INSTALLATION

Align lower door pin with lower hinge pin mounting hole. Then

align upper door pin with upper hinge pin mounting hole pull down

on pin and insert it into the mounting hole.Door can be hinged to

the right or left by reversing top and bottom.

Upper Hinge Pin

Lower Hinge Pin

Upper Hinge Pin Mounting Hole

Lower

Hinge Pin

Mounting Hole

Door

Magnet Stop

Door Bracket installs in

the same fashion as the

Dual Hinge Bracket

Route cables through fingers of P -ATCH

RUNNER Vertical Manager maintaining

cable bend radii. Use a slot on the PATCH-

RUNNER Vertical Cable Manager that is the

same height as the patch panel. Proper

routing for angled patch panel and flat

patch panel shown below.

Angled Patch Panel Detail Flat Patch Panel Detail

Patch Panels Through

PATCHRUNNER Vertical Cable Manager

ROUTING CABLE

Note: For cleaning PANDUIT recommends using ‘SIMPLE GREEN’ all

purpose cleaner (or local equivalent) and a lint free cloth

Note: For cleaning P SANDUIT recommends using ‘ IMPLE GREEN’ all

purpose cleaner (or local equivalent) and a lint free cloth

Product specificaties

Merk:	Panduit
Categorie:	Niet gecategoriseerd
Model:	PRV679
Kleur van het product:	Zwart
Breedte:	152 mm
Diepte:	417 mm
Hoogte:	2004 mm
Materiaal behuizing:	Acrylonitrile butadiene styrene (ABS), Steel
Duurzaamheidscertificaten:	RoHS
Maat:	19.23 "
Rackcapaciteit:	42U