Panduit Pan-Punch 110 Handleiding

Panduit Niet gecategoriseerd Pan-Punch 110

Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit Pan-Punch 110 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 1 of 2

Pan-Punch 110 Punchdown System

Part Numbers: P110KB1004Y, P110KB1005Y, P110KB3004Y, P110KB3005Y, P110B1004R2Y,

P110B1005R2Y, P110B1004R4WJY, P110B1005R4WJY

CABLE REQUIREMENT: Terminates most 22-26 AWG solid or stranded

IWC wire with a 0.050" (1.27mm) max. o.d., either PVC or Plenum rated.

INSTALLATION

1. Use appropriate mounting hardware to install base on

desired surface as shown in Figure 1, 3/4" plywood is

recommended. (Tip: Panduit lettering should be upright).

2. Route cables through slots in the base as shown in Figures

1a (4-pair installation) or 1b (25-pair installation). The wire

strip color markings from left to right are white, red, blue,

yellow, and violet.

3. Insert each pair into position in wire strip slots while

maintaining the proper color sequence. Cable jacket end

should be within 1/2" from where cable pairs are inserted.

Cable pairs must remain twisted up to the point of

connection for Category 5e installation.

4. Inspect cable pair color placement prior to using a PDT110

single wire punchdown tool or PDT110M multi-pair

punchdown tool to seat and cut the pairs to length.

5. Position the connecting block over the wired base.

6. Secure the connecting block in place using the PDT110M

multi-pair punchdown tool. It is important to keep the tool

perpendicular to the base to ensure a good termination. Use

a combination of 3, 4, and 5-pair connecting blocks to

completely fill the wire strip, such as:

- Five 5-pair connecting blocks

- Five 4-pair connecting blocks and one 5-pair

connecting block

- Seven 3-pair connecting blocks and one 4-pair

connecting block

Figure 1a (4-pair installation)

Figure 1b (25-pair installation)

Figure 2b

Figure 2a

5 PAIR KIT

4 PAIR KIT

LOCATION

Mounting a system at the right height will make wiring changes The optimum heiand additions cost efficient. ght, from the

floor to the top of a 300 pair Pan-Punch base, is 68 inches. If the customer needs don’t exceed the wiring capacity of one

base of 100 pair, the optimum distance from the floor to the top of the system can be reduced to 43 inches. This height will

allow for expansion of 300 pair on top and 300 pair underneath.

4-pair cables are installed from the center out to the sides, in groups of

three. Three cables exit from the left and three exit from the right. Each

channel will contain 12 cables - 6 for upper strip and 6 for lower strip. Far

right slot will be unused.

For clarity, only first two cables are shown. Repeat for other side

WHITE RED BLUE YELLOW VIOLET

25 pair cable (for clarity, only 5 pairs shown) Tip colors marked in 5 pair increments

Notes:

1. Strip back outer jacket of 25-pair cable to edge of wiring block (up to

10 inches) and load one complete wire strip.

2. Follow tip color code sequence as indicated on wire strip.

P110CB

CONNECTING BLOCK

WIRE STRIP

P110B BASE

PDT110M

5-PAIR IMPACT TOOL

Product specificaties

Merk:	Panduit
Categorie:	Niet gecategoriseerd
Model:	Pan-Punch 110
Kleur van het product:	Ivoor
Breedte:	272.1 mm
Diepte:	85.9 mm
Hoogte:	87.5 mm
Duurzaamheidscertificaten:	RoHS
Aantal poorten:	72