Panduit P110KB1005Y Handleiding

Panduit Niet gecategoriseerd P110KB1005Y

Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit P110KB1005Y (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 1 of 2

Pan-Punch 110 Punchdown System

Part Numbers: P110KB1004Y, P110KB1005Y, P110KB3004Y, P110KB3005Y, P110B1004R2Y,

P110B1005R2Y, P110B1004R4WJY, P110B1005R4WJY

CABLE REQUIREMENT: Terminates most 22-26 AWG solid or stranded

IWC wire with a 0.050" (1.27mm) max. o.d., either PVC or Plenum rated.

INSTALLATION

1. Use appropriate mounting hardware to install base on

desired surface as shown in Figure 1, 3/4" plywood is

recommended. (Tip: Panduit lettering should be upright).

2. Route cables through slots in the base as shown in Figures

1a (4-pair installation) or 1b (25-pair installation). The wire

strip color markings from left to right are white, red, blue,

yellow, and violet.

3. Insert each pair into position in wire strip slots while

maintaining the proper color sequence. Cable jacket end

should be within 1/2" from where cable pairs are inserted.

Cable pairs must remain twisted up to the point of

connection for Category 5e installation.

4. Inspect cable pair color placement prior to using a PDT110

single wire punchdown tool or PDT110M multi-pair

punchdown tool to seat and cut the pairs to length.

5. Position the connecting block over the wired base.

6. Secure the connecting block in place using the PDT110M

multi-pair punchdown tool. It is important to keep the tool

perpendicular to the base to ensure a good termination. Use

a combination of 3, 4, and 5-pair connecting blocks to

completely fill the wire strip, such as:

- Five 5-pair connecting blocks

- Five 4-pair connecting blocks and one 5-pair

connecting block

- Seven 3-pair connecting blocks and one 4-pair

connecting block

Figure 1a (4-pair installation)

Figure 1b (25-pair installation)

Figure 2b

Figure 2a

5 PAIR KIT

4 PAIR KIT

LOCATION

Mounting a system at the right height will make wiring changes The optimum heiand additions cost efficient. ght, from the

floor to the top of a 300 pair Pan-Punch base, is 68 inches. If the customer needs don’t exceed the wiring capacity of one

base of 100 pair, the optimum distance from the floor to the top of the system can be reduced to 43 inches. This height will

allow for expansion of 300 pair on top and 300 pair underneath.

4-pair cables are installed from the center out to the sides, in groups of

three. Three cables exit from the left and three exit from the right. Each

channel will contain 12 cables - 6 for upper strip and 6 for lower strip. Far

right slot will be unused.

For clarity, only first two cables are shown. Repeat for other side

WHITE RED BLUE YELLOW VIOLET

25 pair cable (for clarity, only 5 pairs shown) Tip colors marked in 5 pair increments

Notes:

1. Strip back outer jacket of 25-pair cable to edge of wiring block (up to

10 inches) and load one complete wire strip.

2. Follow tip color code sequence as indicated on wire strip.

P110CB

CONNECTING BLOCK

WIRE STRIP

P110B BASE

PDT110M

5-PAIR IMPACT TOOL

E-mail:

techsupport@panduit.com

Phone:

866-405-6654

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

www.panduit.com

Page 2 of 2

Figure 3

Figure 4

CABLE REQUIREMENT: Terminates most 22-26 AWG solid or stranded

IWC wire with a 0.050" (1.27mm) max. o.d., either PVC or Plenum rated.

7. Once the connecting blocks have been seated, cross-connect

wires can be terminated to the top of the connecting blocks or

Pan-Punch 110 patch cords can be installed. If cross-

connecting, reference Fig. 3.

8. Add cable identification to the label, fold label, and slide it into

the label holder. The label and label holder snap into position

on the base in-between rows of connecting blocks as shown in

Figure 4.

Notes:

1. Pan-Punch product terminates most 22-26 AWG solid or stranded IWC wire with a 0.050" (1.27mm) max. o.d., either PVC or plenum rated.

2. Never install wire into a slot previously used for a larger gauge.

3. Be careful to strip back cable jacket only as required for termination.

4. Use care to maintain pair twists to within 0.50" (13mm) of the termination strip.

5. When stripping cable jacket, be careful not to cut the insulation on the individual wires.

6. Avoid sharp bends when routing cable.

As with all Wiring Accessories, the following statements apply:

1. Never install communications wiring during a lightning storm.

2. Never install communications wiring in wet locations unless the product is specifically designed for use in wet locations.

3. Never touch uninsulated communications wiring or terminals unless the communication line has been disconnected at the network interface.

4. Use caution when installing or modifying communication wiring.

T1 R1 T2 R2 T3 R3 T4 R4 T5 R5

BLUE ORANGE GREEN BROWN SLATE

TOP VIEW OF 5-PAIR CONNECTING BLOCK

PD110LH

LABEL HOLDER

CONNECTING BLOCK

P110CB (CREME)

P110CBIG (GRAY) P110B BASE

Pair Tip Color Ring Color

1 White/Blue Blue

2 White/Orange Orange

3 White/Green Green

4 White/Brown Brown

5 White/Slate Slate

6 Red/Blue Blue

7 Red/Orange Orange

8 Red/Green Green

9 Red/Brown Brown

10 Red/Slate Slate

11 Black/Blue Blue

12 Black/Orange Orange

13 Black/Green Green

14 Black/Brown Brown

15 Black/Slate Slate

16 Yellow/Blue Blue

17 Yellow/Orange Orange

18 Yellow/Green Green

19 Yellow/Brown Brown

20 Yellow/Slate Slate

21 Violet/Blue Blue

22 Violet/Orange Orange

23 Violet/Green Green

24 Violet/Brown Brown

25 Violet/Slate Slate

Product specificaties

Merk:	Panduit
Categorie:	Niet gecategoriseerd
Model:	P110KB1005Y
Kleur van het product:	Ivoor
Breedte:	272.1 mm
Diepte:	85.9 mm
Hoogte:	87.5 mm
Duurzaamheidscertificaten:	RoHS
Aantal poorten:	20