Panduit MTRTH Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Panduit MTRTH (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 242 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
MTRTH & MTRTLS: PA25279A01_02 Page: 1 of 8 4-2009
MTRTH and MTRTLS PA25279A01
Rev. 02 4-2009
MRT and MRS METAL CABLE TIE RETAINED TENSION INSTALLATION TOOLS
OPERATION INSTRUCTIONS
© Panduit Corp. 2009
INTRODUCTION
The MTRTH Retained Tension Installation Tool is used for installing PANDUIT MRT and MRS Ball Lock
Ties in widths of 5/16” (7.9mm) Heavy (H) cross-sections.
The MTRTLS Retained Tension Installation Tool is used for installing PANDUIT MRT and MRS Ball Lock
Ties in widths of 3/16” (4.6mm) Standard (S) cross-sections. Included with this tool is an anvil, which can
be changed for installing MRT and MRS ties in widths of 1/4” (6.4mm) Light-Heavy (LH) cross-sections.
Changeover Kits are available (listed on Page 7), which allow installation of all three cross-sections of
MRT and MRS Ties with either tool.
Note: This tool is not intended for other uses such as cutting or tensioning other types of
fastening devices.
SAFETY PRACTICES
ALWAYS wear safety glasses when using this tool.
DO NOT place fingers near cutting blade during tool actuation.
Fingers may be pinched or injured by cutter blade.
DO NOT use tool on live electrical sources.
TOOL FEATURES
A. Ball Set / Cutting Handle Lever
B. Upper Handle
C. Tension Indicator Window
D. Tension Handle
E. Adjustment Knob
F. Tensioning Split Mandrel
G. Detent and Setshear Finger
H. Anvil
NOTE: In the interest of higher quality and
value, PANDUIT products are continually being
improved and updated.
Consequently, pictures may vary from the
enclosed product.
Website: www.panduit.com
E-mail: cs@panduit.com
Technical Support:
See back cover for contact
information.
MTRTH and MTRTLS OPERATION INSTRUCTIONS
MTRTH & MTRTLS: PA25279A01_02 Page: 2 of 8 4-2009
MTRTH and MTRTLS TOOL MAINTENANCE
TO INHIBIT CORROSION AND MAINTAIN PERFORMANCE OF THE TOOL, KEEP THE METAL
SURFACES COATED WITH A LIGHT OIL (3-IN-ONE® OR EQUIVALENT).
The tool must be set to the proper tension range based on ties to be installed. Per the above chart, turn
the tension knob, so that mark is aligned with correct setting on Tension Setting Label (see above).
MTRTH and MTRTLS OPERATION INSTRUCTIONS
STEP 1 STEP 2
With the tie surrounding the bundle, insert the end
of the tie into the head/buckle on the tie.
Draw the tie up as tight as possible by hand.
STEP 3
Insert the end of the tie into the tool between Setshear Finger (#1) and Anvil (#2).
STRAP SIZE SETTING
3/16" (4.6mm) S
1/4" (6.4mm) LH
5/16" (7.9mm) H
Tie inserted
in gap here
#1
#2
MTRTH and MTRTLS OPERATION INSTRUCTIONS
MTRTH & MTRTLS: PA25279A01_02 Page: 3 of 8 4-2009
STEP 4
As the tie end is fed through the tool insert the tie end through the Tensioning Split Mandrel.
Pull tool tight to bundle.
CRITICAL: Tool Must Be In-line with the Tie Head
STEP 5


Product specificaties

Merk: Panduit
Categorie: Niet gecategoriseerd
Model: MTRTH

Heb je hulp nodig?

Als je hulp nodig hebt met Panduit MTRTH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Panduit

Panduit

Panduit PZNDVK Handleiding

14 December 2024
Panduit

Panduit PZICEA Handleiding

14 December 2024
Panduit

Panduit PZICE Handleiding

14 December 2024
Panduit

Panduit EA001 Handleiding

9 December 2024
Panduit

Panduit EC001 Handleiding

17 November 2024
Panduit

Panduit CDE3 Handleiding

17 November 2024
Panduit

Panduit MEHT187 Handleiding

17 November 2024
Panduit

Panduit FPONE2 Handleiding

13 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd