Panduit FHC39N-08H-LAA Handleiding

Panduit Niet gecategoriseerd FHC39N-08H-LAA

Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit FHC39N-08H-LAA (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 1 of 3

HD Flex LC Splice Cassette and

Fiber Adapter Panel (FAP)

Part Numbers: See chart below

Product Family Cassette Part

Number Cassette Description

12-Fiber LC Splice/FAP Cassette

(LC pigtails not included)

FHSXN-12-10N FAP (Fiber Adapter Panel) Cassette w/ Aqua Zirconia Adapters

FHS9N-12-10N FAP (Fiber Adapter Panel) Cassette w/ Blue Zirconia Adapters

12-Fiber LC Splice Cassette

(Pre-loaded with Discrete Pigtails)

FHSXO-12-10P 12-Fiber OM3 LC Discrete Pigtails; Optimized IL

FHSZO-12-10P 12-Fiber OM4 LC Discrete Pigtails; Optimized IL

FHSZA-12-10P 12-Fiber OM4 LC Discrete Pigtails; Ultra IL

FHS9N-12-10P 12-Fiber OS2 LC Discrete Pigtails; Standard IL

12-Fiber LC Splice Cassette

(Pre-loaded with Ribbon Pigtail)

FHSXO-12-10R 12-Fiber OM3 LC Ribbonized Pigtail; Optimized IL

FHSZO-12-10R 12-Fiber OM4 LC Ribbonized Pigtail; Optimized IL

FHSZA-12-10R 12-Fiber OM4 LC Ribbonized Pigtail; Ultra IL

FHS9N-12-10R 12-Fiber OS2 LC Ribbonized Pigtail; Standard IL



General Information and Contents

1. HD Flex LC Fiber Adapter Panel (FAP)

• Configured to accommodate pre-terminated cable assemblies.

2. HD Flex LC Preconfigured Splice Cassette – Available in 2 Configurations:

• Configured with 12 Discrete Pigtails, (12) 40mm Discrete Splice Sleeves, and 2 Pan-Ty Cable Ties.

• Configured with a 12-Fiber Ribbon Pigtail, (1) 40mm Ribbon Splice Sleeve, and 2 Pan-Ty Cable Ties.

WARNING: UNMATED CONNECTORS MAY EMIT INVISIBLE LASER RADIATION. MAINTAIN DUST CAPS ON UNMATED

CONNECTORS.

CAUTION:

Fiber optic cable is sensitive to excessive pulling, bending, and crushing forces. Consult the manufacturer’s cable specification sheet

for the specific cable in use.

Part Numbers

Cassette base Cassette cover Screw – Aramid yarn

strain relief

Cable tie strain relief

Cover removal latch

Splice sleeve holders

(12 discrete / 1 ribbon)

Cassette release latches

6 Duplex shuttered

LC Adapters

Figure 1

(Fibers not shown)

For complete HD Flex Fiber Cassette Enclosure installation instructions, visit www.panduit.com and search FS111*.

For Technical Support: www.panduit.com/resources/install_maintain.asp

INSTALLATION INSTRUCTIONS

Page 2 of 3

2 3

4 5

6 7

8 9

10 11

(Front of Cassette)

Fiber Color Coding – Telcordia (Standard)

Fiber Color Key

Fiber 1 – Blue Fiber 7 – Red

Fiber 2 – Orange Fiber 8 – Black

Fiber 3 – Green Fiber 9 – Yellow

Fiber 4 – Brown Fiber 10 – Violet

Fiber 5 – Slate Fiber 11 – Rose

Fiber 6 – White Fiber 12 – Aqua



Figure 3

Patch cords

Install patch cords and route cables as shown.

Re-install cover.

Figure 2

Internal dust caps

Remove cover and internal dust caps.

It is recommended to use Panduit cable assemblies.

Note: When using jacketed patch cords, use

maximum cable diameter of 2.0mm and maximum

connector length of 2.0 inches (from end of ferrule to

end of boot).

FAP Termination – Fiber Adapter Panel Cassette

INSTALLATION INSTRUCTIONS

E-mail:

techsupport@panduit.com

Phone:

866-405-6654

For Instructions in Local Languages

and Technical Support:

www.panduit.com/resources/install_maintain.asp www.panduit.com

Page 3 of 3

Figure 5

Incoming field Discrete splice sleeves

Routing tabs

Pan-Ty

Cable Ties

Kevlar

Cable jacket

(Ribbon sleeveoptional)

fibers

Strip incoming field cable outer jacket 20 inches.

Secure with Pan-Ty Cable Ties, and Kevlar with

screw (optional). Max cable diameter: 7.4mm

Expose all fiber ends for splicing. Slide a splice

sleeve onto either the (pigtail or field) fiber. Strip off

approximately 35mm of coating from each fiber.

Wipe the bare fiber with a lint-free tissue soaked with

isopropyl alcohol. Cleave the fiber so that 10mm

(both for 250µm and 900µm coating diameter) of

bare fiber extends past the fiber coating.

Note: Do not clean the bare fiber after it has been

cleaved, and do not let it come in contact with any

surfaces.

Splice all fibers and heat splice sleeve(s). Refer to

splicer manufacturer best practice instructions.

Route spliced fibers into cassette ensuring fibers

are located under the routing tabs. Incoming field

fibers are shown as black dashed lines.

Secure splice sleeves within splice organizer.

Re-install cover.

Figure 4

Screw

Pre-loaded pigtail fibers

Splice

organizer

(12 discrete)

Splice organizer (ribbon)

Pigtail Termination – LC Splice Cassettes

Remove the cover.

Pre-loaded pigtail fibers are shown as grey dashed

lines.

Product specificaties

Merk:	Panduit
Categorie:	Niet gecategoriseerd
Model:	FHC39N-08H-LAA
Kleur van het product:	Blauw
Aantal per verpakking:	1 stuk(s)
Aantal connectors:	8
Verpakkingsvolume:	0.6576 cm³
Categorie:	OS2
Aansluiting type:	LC/MPO