Panduit CT-260 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit CT-260 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
CT-260
CRIMPING TOOL
OPERATION INSTRUCTIONS
Page: 1 of 2
PA24429A01
REV.: 03 6-2018
OPERATION INSTRUCTIONS
© Panduit Corp. 2018
CT-260
Technical Support:
1-800-777-3300
E-mail:
techsupport@panduit.com
See product packaging or contact Customer Service for
UL/CSA approved tooling/product combination.
CAUTION:
Verify power is “OFF before working on wiring with this tool.
The plastic grips are for the user’s comfort,
and are not intended to insulate against electrical shock
while working on live electrical circuits.
NON-INSULATED AND INSULATED
PARALLEL SPLICE
INSTRUCTIONS
1. Insert stripped wire into each end of the
parallel splice. (See product packaging
for proper strip lengths.)
2. Locate parallel splice in proper crimp
pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
WIRE CUTTER for No. 10 AWG and
smaller copper wire.
CRIMP POCKETS for Pan-Term
insulated and non-insulated terminals,
disconnects, wire joints and splices on No.
22 to 10 AWG solid or stranded wire.
This tool is made of hardened steel and is
protected with a light coat of oil.
CRIMP POCKET
CRIMP POCKET
NON-INSULATED
INSULATED
www.panduit.com
NON-INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper non-
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Repeat for other end of butt splice.
INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Close insulation if desired.
6. Repeat for other end of butt splice.
CRIMP POCKET
CRIMP POCKET
Page: 2 of 2
OPERATION INSTRUCTIONS
NOTE:
In the interest of higher
quality and value, Panduit is
constantly improving and
updating our products.
Consequently, pictures herein may
vary from the actual product.
CT-260
© Panduit Corp. 2018
NON-INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
non-insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
5. Close insulation if desired.
NON-INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper non-insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
5. Close insulation if desired.
CRIMP POCKET
CRIMP POCKET CRIMP POCKET
CRIMP POCKET


Product specificaties

Merk: Panduit
Categorie: Niet gecategoriseerd
Model: CT-260

Heb je hulp nodig?

Als je hulp nodig hebt met Panduit CT-260 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Panduit

Panduit

Panduit EC001 Handleiding

17 November 2024
Panduit

Panduit CDE3 Handleiding

17 November 2024
Panduit

Panduit MEHT187 Handleiding

17 November 2024
Panduit

Panduit FPONE2 Handleiding

13 November 2024
Panduit

Panduit FPONE3 Handleiding

13 November 2024
Panduit

Panduit FPONE1 Handleiding

13 November 2024
Panduit

Panduit FPONE4 Handleiding

13 November 2024
Panduit

Panduit AFR4EC Handleiding

18 Oktober 2024
Panduit

Panduit AFR4RA Handleiding

18 Oktober 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd