Panduit CT-2500CHR Handleiding

Panduit Batterij-oplader CT-2500CHR

Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit CT-2500CHR (2 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Page: 1 of 2

CT-2500BC, CT-2500CHR

and CT-2500CHR/E

PA25384A01

Rev. 01 1- 2014

BATTERY CARTRIDGE AND BATTERY CHARGER

USED WITH THE CT-2500 and CT-2500/E TOOLS

OPERATION INSTRUCTIONS

USE OF THE BATTERY CARTRIDGE AND CHARGING UNIT

The charging unit is run with a nominal voltage of 120 V (CT 2500CHR), or (230 V for -

CT- -2500CHR/E) and a frequency of 50 60 Hz. New batteries must be charged prior to use. To

remove the battery, actuate the battery lock and pull it out of the tool. To charge the battery,

connect the power plug of the charging unit with the power supply and slide the battery into the

charging unit. The charging time is 40 minutes. The charging level of the battery cartridge can be

checked by the right LED (multi color) of the charging unit.-

Left LED (Red) Right LED (Multi -color)

Red Charging unit ready to operate Battery defective

Red Flashing

Charging unit out of order.

New or unused batteries whose

nominal capacity is not sufficient.

Battery too hot or too cold.

Remove battery.

Safety components possibly defective.

Green – Charging cycle starts

Green Flashing –

Battery fully charged.

Charging unit switches automatically into a

maintaining mode. Battery can stay in charger

for indefinite time w/o being damaged.

Yellow

–

Battery at least 90% charged.

Charging cycle can be terminated.

– If the right LED does not light up, the circuit of

the battery is disconnected or the battery is

incorrectly polarized.

• If the nominal capacity of the battery is not achieved, e.g. at first charge, the battery is not

necessarily faulty. Full capacity can be achieved after (3) charging/discharging cycles.

• When the speed of the tool decreases noticeably, the battery must be recharged.

ATTENTION:

Do Not recharge a partially discharged battery as a precaution.

• Charge the battery at room temperature between 50°F and 104°F (10°C and 40°C).

• Charging batteries at low temperatures, under 41°F (5°C) is not possible. Increase battery

temperature before starting the charging cycle.

• Do Not expose the charging unit to rain or snow.

• Do Not charge a battery in the vicinity of explosive materials and gases.

• No other batteries (e.g. dry batteries or car batteries, etc.) are to be used in the tool or in the

charging unit.

• Do Not use the cord to transport the charging unit, or to pull the plug out of a wall socket with

force.

• Do Not insert foreign objects into the ducts of the charging unit. Pull the plug of the charging

unit after charging. Do Not disassemble the charging unit or battery.

CT- -2500BC, CT 2500CHR

and CT-2500CHR/E

Page of 2 2

ATTENTION:

Do Not place the battery in your pocket or in your toolbox if there are any

conductive materials in it such as coins, keys, tools or other metallic parts.

TERMINATIONS PER BATTERY CHARGE

The estimated number of terminations before the battery will need to be recharged is dependent on

variables such as the connector size and type being terminated, ambient temperature, and time

lapsed between termination cycles as well as other variables.

E- : mail

techsupport@panduit.com

EU Website:

www.panduit.com/emea

E- mail: emeatoolservicecenter

@panduit.com

www.panduit.com

Technical Support:

1- - - 8 888 506 5400, ext. 3255

P anduit Europe, EMEA Service Center

Almelo, Netherlands

Tel.: 31 546 580 452- - -

Fax: 44 208 601 7209

Product specificaties

Merk:	Panduit
Categorie:	Batterij-oplader
Model:	CT-2500CHR
Kleur van het product:	Zwart
Soort:	Batterijlader voor binnengebruik
Type stroombron:	AC
Ingangsspanning:	120 V
Compatibele producten:	CT-2500, CT-2600