Panduit CT-200 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit CT-200 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
CT-200
CRIMPING TOOL
OPERATION INSTRUCTIONS
Page: 1 of 1
PA24428A01
REV.: 02 6-2018
OPERATION INSTRUCTIONS
© Panduit Corp. 2018
CT-200
Technical Support:
1-800-777-3300
E-mail:
techsupport@panduit.com
WIRE CUTTER for No. 10 AWG and
smaller copper wire.
CRIMP POCKET for Pan-Term non-
insulated terminals, disconnects,
splices and wire joints.
The 12-10 pocket is for No. 12 to No. 10
solid or stranded wire; the 22-14 pocket
is for No. 22 to No. 14 solid or stranded
wire. The crimp should be centrally
located on the barrel with the indenter
on the seam, and the dies fully closed
for best results.
This tool is made of hardened steel and
is protected with a light coat of oil.
See product packaging or contact Customer Service for
UL/CSA approved tooling/product combination.
NON-INSULATED WIRE JOINT
INSTRUCTIONS
1. Twist ends of stripped wire together,
trim and insert into wire joint. (See
product packaging for proper strip
lengths and trimming instructions.)
2. Locate wire joint in proper non-insulated
crimp pocket.
3. Position crimp pocket on the center of
the metal barrel.
4. Squeeze handles firmly.
CRIMP POCKET
NON-INSULATED BUTT SPLICE
INSTRUCTIONS
1. Insert stripped wire into end of the butt
splice to internal wire stop. (See product
packaging for proper strip lengths.)
2. Locate butt splice in proper non-
insulated crimp pocket.
3. Position crimp pocket on the center of
the metal barrel half with wire inserted.
4. Squeeze handles firmly.
5. Repeat for other end of butt splice.
CRIMP POCKET
NON-INSULATED
TERMINAL AND DISCONNECT
INSTRUCTIONS
1. Insert stripped wire into terminal or
disconnect until a minimum of 1/32" of
conductor extends beyond barrel. (See
product packaging for proper strip
lengths.)
2. Locate terminal or disconnect in proper
non-insulated crimp pocket.
3. Position crimp pocket on the center of the
metal barrel.
4. Squeeze handles firmly.
CRIMP POCKET
CAUTION:
Verify power is “OFF” before working on wiring with this tool.
The plastic grips are for the user’s comfort,
and are not intended to insulate against electrical shock
while working on live electrical circuits.
www.panduit.com


Product specificaties

Merk: Panduit
Categorie: Niet gecategoriseerd
Model: CT-200

Heb je hulp nodig?

Als je hulp nodig hebt met Panduit CT-200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Panduit

Panduit

Panduit EC001 Handleiding

17 November 2024
Panduit

Panduit CDE3 Handleiding

17 November 2024
Panduit

Panduit MEHT187 Handleiding

17 November 2024
Panduit

Panduit FPONE2 Handleiding

13 November 2024
Panduit

Panduit FPONE3 Handleiding

13 November 2024
Panduit

Panduit FPONE1 Handleiding

13 November 2024
Panduit

Panduit FPONE4 Handleiding

13 November 2024
Panduit

Panduit AFR4EC Handleiding

18 Oktober 2024
Panduit

Panduit AFR4RA Handleiding

18 Oktober 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd