Panduit CT-1090 Handleiding

Panduit Handgereedschap CT-1090

Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit CT-1090 (2 pagina's) in de categorie Handgereedschap. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Page: 1 of 2

CONTROLLED CYCLE FERRULE CRIMPING TOOL

OPERATION, INSPECTION and MAINTENANCE INSTRUCTIONS

1. With the handles in the open position, insert the ferrule

into the crimp pocket. Make sure that the ferrule is

inserted fully into the crimp die (see Figure 2).

2. Insert the stripped wire into the ferrule until the wire

stops. Refer to product packaging for wire strip length.

3. Crimp the ferrule by closing the handles until the

controlled cycle mechanism releases. Upon release,

the handles will open automatically and the crimped

ferrule can be removed.

NOTE: Crimp entire uninsulated ferrule length. This may

require additional crimps.

CT-1090 TOOL

Fig. 1

Fig. 2

Stripped

Wire

Crimp Die

Controlled cycle mechanism

prevents tool from opening

before crimp cycle is completed.

Manual release lever, push

forward in the event that

controlled cycle mechanism

must be released.

Cushioned handle grips

CRIMP POCKETS for Ferrule

terminals. Refer to product

packaging for wire range and

proper crimp pocket. Crimp

pockets are identified with

applicable wire range.

Ferrule - Wire

crimp section

Ferrule Insulated

section

CT-1090

PA28190A01

REV: 00 9-2016

E-mail:

techsupport@panduit.com

For Technical Support:

1-800-777-3300

www.panduit.com

CAUTION:

Verify power is “OFF” before working on

wiring with these tools.

The plastic grips are for the user’s

comfort, and are not intended

to insulate against electrical shock while

working on live electrical circuits.

INSPECTION / MAINTENANCE

NEW TOOLS -

BEFORE PLACING INTO SERVICE:

All Panduit crimping tools are inspected before they are

shipped from the factory. All new tools should be

inspected before being used.

New tools are shipped, factory lubricated, in protective

packaging. After inspection, simply clean any excess oil

from the crimping dies and place into service.

When the tool is not in use, keep the handles closed to

prevent objects from becoming lodged in the crimping

area. Store the tool in a clean, dry area.

Page: 2 of 2

IN SERVICE TOOLS - AFTER TOOLS HAVE BEEN IN SERVICE:

It is recommended that each operator of the tool be made aware of - and responsible for following these maintenance

steps:

In-service tools should be cleaned and inspected at least ONCE A MONTH. To clean - wipe with a clean cloth.

In-service tools should be lubricated ONCE A WEEK, and after every cleaning. Lubricate all pins, pivots and bearing

surfaces with DOW CORNING®Molykote BR2 Plus.

Be sure to clean any excess oil from the crimping dies before using.

®Molykote BR2 Plus is the Registered Trademark of DOW CORNING.

VISUAL INSPECTION

1. Visually inspect the tool for missing or loose pins; then close the tool and note the return action of the handles.

2. Inspect the crimping dies for worn, chipped or broken edges.

3. If parts are missing, defective or damaged; contact Panduit for information on repair or replacement of tools.

4. Check for debris in dies. Any debris will need to be removed prior to tool use.

and MAINTENANCE INSTRUCTIONS CT-1090

Product specificaties

Merk:	Panduit
Categorie:	Handgereedschap
Model:	CT-1090
Kleur van het product:	Black, Grey
Gewicht:	510 g
Breedte:	20 mm
Soort:	Krimptang
Duurzaamheidscertificaten:	RoHS
Aantal per verpakking:	1 stuk(s)
Afmeting AWG-draad (min):	26
AWG-draadafmeting (max):	10