Panduit CT-1006 Handleiding
Panduit
Handgereedschap
CT-1006
Lees hieronder de 📖 handleiding in het Nederlandse voor Panduit CT-1006 (2 pagina's) in de categorie Handgereedschap. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/2
© Panduit Corp. 2018
Page: 1 of 2
CONTROLLED CYCLE FERRULE CRIMPING TOOLS
OPERATION, INSPECTION and MAINTENANCE INSTRUCTIONS
1. With the handles in
the open position,
insert the ferrule
into the opening at
the top of the tool.
Make sure that the
ferrule insulation or
flared end is up
(see Figure 2). Do
not allow insulation
to be inserted into
crimp die. Close
handles until dies
just slightly crimp
ferrule.
2. Insert the stripped wire into the ferrule until the wire
stops. Refer to product packaging for wire strip length.
3. Crimp the ferrule by closing the handles until the
controlled cycle mechanism releases. Upon release,
the handles will open automatically and the crimped
ferrule can be removed.
1. With the handles in
the open position,
insert the ferrule
into the crimp
pocket. Make sure
that the ferrule is
inserted fully into
the crimp die (see
Figure 4).
2. Insert the stripped
wire into the ferrule
until the wire stops.
Refer to product
packaging for wire
strip length.
3. Crimp the ferrule by closing the handles until the
controlled cycle mechanism releases. Upon release,
the handles will open automatically and the crimped
ferrule can be removed.
NOTE: Crimp entire uninsulated ferrule length. This may
require additional crimps.
CT-1002, CT-1003 and CT-1004 TOOLS
CT-1005 and CT-1006 TOOLS
Cushioned handle grips
CRIMP POCKET for Insulated
and Non-Insulated Ferrules. Part
usage dependent on wire range.
Refer to product packaging for
proper wire combination.
Controlled cycle mechanism
prevents tool from opening
before crimp cycle is complete.
Manual release lever, push
forward in the event that
controlled cycle mechanism
must be released.
Fig. 1
Fig. 3 Fig. 4
Fig. 2
Stripped
Wire
Crimp Die
Die Closure Alignment
(not a crimp pocket)
Controlled cycle mechanism pre-
vents tool from opening before
crimp cycle is completed.
Manual release lever, push
forward in the event that
controlled cycle mechanism
must be released.
Cushioned handle grips
Ferrule
Insulation
section Ferrule -
Metal crimp
section
Stripped
Wire
CRIMP POCKETS for Ferrule
terminals. Refer to product
packaging for wire range and
proper crimp pocket. Crimp
pockets are identified with
applicable wire range.
Ferrule - Wire
crimp section
Ferrule Insulated
section
CT-1002, CT-1003, CT-1004,
CT-1005 and CT-1006
PA24073A01
REV: 04 2-2018
E-mail:
techsupport@panduit.com
For Technical Support:
1-800-777-3300
www.panduit.com
CAUTION:
Verify power is “OFF” before working
on wiring with these tools.
The plastic grips are for the user’s
comfort, and are not intended
to insulate against electrical shock
while working on live electrical circuits.
Page: 2 of 2
NEW TOOLS - BEFORE PLACING INTO SERVICE:
All Panduit crimping tools are inspected before they are shipped from the factory. All new tools should be inspected
before being used.
New tools are shipped, factory lubricated, in protective packaging. After inspection, simply clean any excess oil from the
crimping dies and place into service.
When the tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping area. Store
the tool in a clean, dry area.
IN SERVICE TOOLS - AFTER TOOLS HAVE BEEN IN SERVICE:
It is recommended that each operator of the tool be made aware of - and responsible for following these maintenance
steps:
In-service tools should be cleaned and inspected at least ONCE A MONTH. To clean - wipe with a clean cloth.
In-service tools should be lubricated ONCE A WEEK, and after every cleaning. Lubricate all pins, pivots and bearing
surfaces with DOW CORNING®Molykote BR2 Plus.
Be sure to clean any excess oil from the crimping dies before using.
®Molykote BR2 Plus is the Registered Trademark of DOW CORNING.
INSPECTION / MAINTENANCE
VISUAL INSPECTION
1. Visually inspect the tool for missing or loose pins; then close the tool and note the return action of the handles.
2. Inspect the crimping dies for worn, chipped or broken edges.
3. If parts are missing, defective or damaged; contact Panduit for information on repair or replacement of tools.
4. Check for debris in dies. Any debris will need to be removed prior to tool use.
© Panduit Corp. 2018 CT-1002, CT-1003, CT-1004, CT-1005 and CT-1006
OPERATION, INSPECTION and MAINTENANCE INSTRUCTIONS
Product specificaties
| Merk: | Panduit |
| Categorie: | Handgereedschap |
| Model: | CT-1006 |
| Kleur van het product: | Black, Green |
| Diepte: | 217.42 mm |
| Soort: | Krimptang |
| Aantal per verpakking: | 1 stuk(s) |
Heb je hulp nodig?
Als je hulp nodig hebt met Panduit CT-1006 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Handgereedschap Panduit
17 November 2024
23 Augustus 2024
23 Augustus 2024
23 Augustus 2024
23 Augustus 2024
20 Augustus 2024
20 Augustus 2024
20 Augustus 2024
6 Juli 2023
4 Juli 2023
Handleiding Handgereedschap
- Handgereedschap Bosch
- Handgereedschap IKEA
- Handgereedschap DeWalt
- Handgereedschap Ambiano
- Handgereedschap Blaupunkt
- Handgereedschap Dremel
- Handgereedschap Einhell
- Handgereedschap Ideal
- Handgereedschap Laserliner
- Handgereedschap Makita
- Handgereedschap Milwaukee
- Handgereedschap Nedis
- Handgereedschap Powerfix
- Handgereedschap Ryobi
- Handgereedschap Silverline
- Handgereedschap Stanley
- Handgereedschap Velleman
- Handgereedschap Vonroc
- Handgereedschap Wiha
- Handgereedschap Ozito
- Handgereedschap Steren
- Handgereedschap Klein Tools
- Handgereedschap Meec Tools
- Handgereedschap RIDGID
- Handgereedschap Hazet
- Handgereedschap Baumr-AG
- Handgereedschap Jokari
- Handgereedschap Victa
- Handgereedschap Wera
Nieuwste handleidingen voor Handgereedschap
7 December 2024
7 December 2024
7 December 2024
7 December 2024
4 December 2024
20 November 2024
20 November 2024
20 November 2024
18 November 2024
16 November 2024