Panasonic RX-D23P Handleiding
Panasonic
Stereosets
RX-D23P
Lees hieronder de 📖 handleiding in het Nederlandse voor Panasonic RX-D23P (8 pagina's) in de categorie Stereosets. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
Before connecting, operating or adjusting
this product, please read these instructions
completely.
Please keep this manual for future reference.
Power sources
The unit can be powered with household AC power or dry cell batteries (not included).
Insert memory batteries (not included) to save stored CD programs and radio stations.
Memory back-up
Insert batteries (not included) to save CD pro-
grams and radio stations you have set. If memory
batteries are not used, memory items are erased
in the following situations:
• Power failures,
• The power cord is disconnected from the power
outlet,
• The power cord is connected to the unit while
the unit is being powered by batteries.
(R6/LR6, AA, UM-3)
When to change the batteries
The batteries last about a year.
Connect the unit to AC power before replacing
the batteries.
Removing the batteries
Press the negative end of the number 4 battery
and remove the batteries. (Remove the power
batteries first.)
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
Using a household AC outlet
Connect the power cord firmly to the unit and the
outlet.
• Before connecting or disconnecting the cord,
stop the tape and switch [ ] to “TAPE/
” to turn the power off. The memory bat-
teries are worn out faster if the cord is discon-
nected with the power still on.
•Conserving power
The unit consumes 1W even when it is turned
off with [ ]. To save power when the
unit is not to be used for a long time, unplug it
from the household AC outlet. Remember to
reset the radio stations and any other memory
items before using the unit again if you haven’t
inserted memory batteries.
Using batteries
The unit cannot be powered by batteries if the
power cord is connected.
(R20/LR20, D, UM-1)
When to change the batteries
Sound quality and operations are affected when
the batteries are running low. Replace all six
batteries. It is also a good idea to replace all the
batteries before recording.
Removing the batteries
Open the battery cover
and insert your finger in
the hole on the bottom
of the unit and push out.
RQT6742- P1
Household AC outlet
(AC 120
V, 60
Hz)
AC power cord
(included) Inner row
Outer row
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions
carefully.
These operating instructions fundamentally explain the operation of
RX-D23.
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for fu-
ture reference.
MODEL NUMBER _________________________________
SERIAL NUMBER _________________________________
The illustrations show RX-D23.
Supplied accessories
Please check and identify the supplied accessories.
Use numbers indicated in parentheses when ask-
ing for replacement parts.
(Only for U.S.A.)
To order accessories contact 1-800-332-5368 or
web site (http://www.panasonic.com).
AC power supply cord (polarized) (RJA0065-1D) .................. 1pc.
Note
The included AC power supply cord is for use with this unit only. Do
not use it with other equipment.
Remote control transmitter ..................................................... 1pc.
(EUR648257)
Portable Stereo
CD System
Operating Instructions
Model No.
RX-D23
RX-D20
P PCPL
RQT6742
2
TUNER
XBS
CD
Controls
Main unit:
Remote control signal sensor (SENSOR)
Tape play button ( PLAY)
Rewind/review button ( REW/REV)
Fast-forward/cue button ( FF/CUE)
Stop/eject button ( / STOP/EJECT)
Tune mode, CD play mode select button
(TUNE MODE, CD PLAY MODE)
Speaker
XBS button
Press to boost the bass sound.
Press again to turn off.
Display
Pause button ( PAUSE)
CD lid open/close
( CD OPEN/CLOSE)
Record button ( )
Function select switch
( )
CD lid
Note
These speakers do not have magnetic shielding. Do not place
them near televisions, personal computers or other devices
easily influenced by magnetism.
Tape lid
Auto scan button (AUTO SCAN)
(For RX-D23 only)
Center speaker
Volume control
( )
CD play/pause, band
select button ( , BAND)
FM mode select/CD stop/
program clear button
( FM MODE/CLEAR)
Band select button
(BAND)
CD play mode
select button
(CD PLAY MODE)
FM mode select
button (FM MODE)
Preset channel select/
preset scan buttons
( PRESET TUNE )
Normal tuning/CD
skip, search buttons
( , )
CD play/pause button
( )
CD stop/program
clear button
( )
Tuning/CD skip, search buttons
( , TUNE/CD)
Memory button (MEMORY)
Remote control:
The functions of the buttons without descriptions are the same as on
the main unit.
Battery installation
Insert the batteries (not included)
observing the correct polarities (e d, ).
Operation notes
• Do not place obstacles between the remote control signal sensor and
the remote control unit.
• Do not expose the remote control signal sensor to direct sunlight or to
the bright light of fluorescent light.
• Take care to keep the remote control signal sensor and end of the remote
control unit free from dust.
To prevent damage
• Never place heavy items on it.
• Do not disassemble or reconstruct it.
• Do not spill water or other liquids into it.
Correct method of use
Concerning the remote control
Transmission
window
About 7 meters in front
of the signal sensor
Remote control
signal sensor
1
2
R6, AA, UM-3
RQT6742
3
1 Switch [ ] to “TUNER”.
(Power comes on.)
2Press [BAND] to select “FM” or “AM”.
3(Omit this step if using the remote control)
If “ ” is on the display, press
[TUNE MODE] to clear it off .
4Press [–/ ] or [ /+] tog f
tune to the desired station.
The frequency changes one step
each time a button is pressed.
Automatic tuning
Keep [–/
g f] or [ /+] depressed and release when the frequency
display starts to change. A station with good reception is automati-
cally selected and the process stops.
To stop automatic tuning, press [–/
g f] or [ /+] again.
Note
Automatic tuning may stop on a frequency where there is no station if
there is interference. Press [–/
g f] and [ /+] to tune if this occurs.
5Adjust the volume.
To use auto scan
You can search for a station by listening to all tuned-in stations for 8
seconds each.
Preparation: Switch [ ] to “TUNER”.
1. Press [BAND] to select “FM” or “AM”.
2. Press [AUTO SCAN].
Auto scan starts.
3. Press [AUTO SCAN] when you find the desired station.
Auto scan ends when it reaches the original frequency again.
To stop during the process, press [AUTO SCAN].
To improve reception
FM: Extend the whip antenna and adjust its direction.
AM: Adjust facing of the unit.
If noise is excessive in the FM stereo mode
Press [FM MODE]. (“ ” lights up.)
Sound will be produced in monaural, but this also reduces noise.
Press the button again to cancel. (“ ” goes out.)
To receive FM broadcasts allocated in 0.1
MHz
(Only from the main unit)
First press [BAND] to select “AM”. Now, press and hold [BAND]. The dis-
play changes in a few seconds to show the current lowest FM frequency.
Continue to hold down the button.
The minimum frequency changes and the step is changed at the same
time. Changing the step erases all preset stations.
Repeat the above to change the step back.
Preset the stations (12 FM and 12 AM) to make tuning simpler.
1Tune to the desired station.
Do steps 1 4– on the left.
2Press [MEMORY].
3 While “ ” and the frequency are
flashing
Press [MEMORY].
4 While “ ” and the preset channel
are flashing
Press [–/ ] or [ /+] tog f
select the desired channel.
(Remote control: [4444
4] or [3333
3])
5Press [MEMORY].
(This completes presetting.)
6Repeat steps 1–5 to preset other stations.
Note
If “ ” goes off during presetting, return to step 2.
Press [BAND] to select “FM” or “AM”.
(Omit this step if using the remote control)
Press [TUNE MODE] to display
“ ”.
Press [–/
g f] or [ /+] to select
the desired channel (1–12).
(Remote control: [44
44
4] or [33
33
3])
To use preset scan
You can search for a station by listening to all preset channels for 8
seconds each.
1. Do steps to above.
For remote control, replace [–/
g f] or [ /+] described below with [4444
4]
or [
3333
3].
2. Press and hold [–/
g f] or [ /+] until “PS” appears on the display.
3. Press [–/
g f] or [ /+] when you find the desired channel.
Preset scan ends after searching through each preset channel once.
To stop during the process, press [–/
g f] or [ /+].
Normal tuning Preset tuning
Listening to radio broadcasts
To listen to preset channels
How to preset
Indicates
auto scan
Indicates
preset scan
“ ” lights when an FM stereo
broadcast is being received.
Preset channel
Preset channel
3
2
1 5 4
1
2 3
2 3 5 4
Product specificaties
| Merk: | Panasonic |
| Categorie: | Stereosets |
| Model: | RX-D23P |
Heb je hulp nodig?
Als je hulp nodig hebt met Panasonic RX-D23P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Stereosets Panasonic
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
Handleiding Stereosets
- Stereosets Philips
- Stereosets Sony
- Stereosets Samsung
- Stereosets LG
- Stereosets Grundig
- Stereosets JVC
- Stereosets Aiwa
- Stereosets Audiosonic
- Stereosets Audizio
- Stereosets Auna
- Stereosets Boston Acoustics
- Stereosets Denver
- Stereosets GPO
- Stereosets Harman Kardon
- Stereosets Hitachi
- Stereosets Hyundai
- Stereosets Lenco
- Stereosets Logik
- Stereosets Nedis
- Stereosets Nikkei
- Stereosets Sencor
- Stereosets Sharp
- Stereosets Silvercrest
- Stereosets Sylvania
- Stereosets Technics
- Stereosets Thomson
- Stereosets OK
- Stereosets Camry
- Stereosets ECG
- Stereosets Caliber
- Stereosets Champion
- Stereosets Naxa
- Stereosets Bush
- Stereosets Curtis
- Stereosets Alba
- Stereosets Lloytron
- Stereosets Trevi
- Stereosets SDigital
Nieuwste handleidingen voor Stereosets
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022
3 Oktober 2022