Ozito ELM-1030U Handleiding

Ozito Grasmaaier ELM-1030U

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito ELM-1030U (3 pagina's) in de categorie Grasmaaier. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
ECOMOW
ELECTRIC MOWER
1000W 305mm
ORIGINAL INSTRUCTIONS
SPECIFICATIONS
Voltage: 220-240V~50/60Hz
Motor: 1000W
No Load Speed: 3,400/min
Cutting Width: 305mm
Cutting Heights: 3 levels, 30-70mm
Catcher Capacity: 25 litre
Power Cord Length: 10m
Protection Class: II
Weight: 7.97kg
ELM-1030U
WHAT’S IN THE BOX
Electric Lawn Mower
Handle Fasteners
Grass Catcher
General safety regulations for this electrical tool
This equipment is not allowed to be used by children. Children should be supervised so that they do not play with the
equipment. Children are not allowed to carry out the cleaning or maintenance. This equipment is not allowed to be used
by people with limited physical, sensory or mental capacities or by those with insufcient knowledge or experience unless
they are supervised or instructed by a person who is responsible for them.
Safety instructions for hand mower
• Before use, check the mains cable and extension cable for signs of damage and aging.
• If the cable is damaged during operation, disconnect it immediately from the power supply.
• Check the machine for signs of damage before use. Repairs may only be carried out by our service workshop. If unusual
vibrations occur during use, switch the machine off immediately and pull the plug. Check the cutters and clean them if
necessary. If the machine continues to vibrate, switch it off, disconnect it from the mains supply and send it to our service
workshop.
• The machine must not be tipped whilst it is being started. Both hands must be on the handle when you start the
machine.
• Worn parts may only be replaced by our service workshop. If necessary contact the service address provided.
WARNINGS
• Do not use the mower if the connection cable is damaged or worn.
• Do not use a damaged cable to connect the machine to the mains supply and do not touch a damaged cable whilst it is
connected to the mains. A damaged cable can result in contact with live parts.
• Do not touch the cutters until the machine has been disconnected from the mains and the cutters have reached a
complete standstill.
• Keep extension cables away from the cutters. The cutters can damage the cables and result in contact with live parts.
• Break the connection with the mains supply (in other words pull the plug out of the socket):
- whenever you leave the machine unattended;
- before released a blocked cutter;
- before inspecting or cleaning and before working on the machine;
- if a foreign body has been struck;
- whenever the machine starts to vibrate oddly.
• Carefully read the instructions for how to operate the machine safely.
• We recommend that the machine is only connected to a power supply protected by means of an earth
-leakage circuit breaker (RCD) with a maximum trip current of 30 mA.
Note
a) Read the directions with due care. Familiarize yourself with the operator controls and proper operation of the machine.
b) Never allow children or other persons who are not familiar with the operating instructions to use the mower. Contact
your local governmental agency for information regarding minimum age requirements for the user.
c) Never mow in the direct vicinity of persons
- especially children
- or animals.
d) Always keep in mind that the operator or user of the equipment is responsible for accidents involving other persons
and/or their property.
Preliminary measures
a) Always wear sturdy, non
-slip footwear and long trousers when mowing. Never mow barefoot or in sandals. Avoid wearing loosely tting clothes or
clothing with hanging belts or cords.
b) Check the ground on which the equipment will be used and remove all objects that could be caught up or violently
ung out.
c) Before using the scythe, visually inspect it to ensure that the blade, mounting bolts and the entire cutting apparatus are
in good working order (i.e. not worn out or damaged). To prevent any imbalance, replace worn out or damaged blades
and mounting bolts as a set only (if applicable). Worn or damaged cutting tools must be replaced.
d) Before use, check the power cable and extension cable for signs of damage and wear. If the cable is damaged
during operation, disconnect it immediately from the power supply. DO NOT TOUCH THE CABLE BEFORE IT IS
DISCONNECTED. Do not use the equipment if the cable is worn or damaged.
e) Remember that if the machine has several cutting tools, the movement of one cutting tool may result in the other
cutting tools starting to rotate.
Handling
a) Only mow in broad daylight or in well-lit conditions.
b) Do not use the machine on wet grass.
c) Always maintain good footing on inclines.
d) Only operate the machine at a walking pace.
e) Always mow across hills i.e. never straight up or straight down.
f) Be particularly careful when you change direction on a slope.
g) Do not mow on overly steep inclines.
h) Always be extra careful when turning the mower around and when pulling it towards you.
i) Switch the mower off , pull the plug and wait until the cutters have reached a complete standstill if you need to tip the
mower over, transport it over surfaces other than grass and if the mower has to be moved from and to the area you wish
to mow.
j) Never use the lawn mower if the guards are damaged or without the attached guards, e.g. deectors and/or grass
catching devices.
k) Use the ON/OFF switch carefully as described in the manufacturer’s instructions. Make sure that your feet are far
enough away from the mower blade!
l) The lawn mower should not be tilted when the motor is switch on unless it has to be raised for starting purposes. In this
case, tilt it as little as absolutely necessary and only raise the side opposite to that of the user.
m) Do not switch on the mower if you are positioned in front of the chute.
n) Never move your hands or feet toward or under any rotating parts. Keep clear of the chute opening at all times.
o) Never lift or carry a lawn mower with the engine running.
p) Switch off the motor and pull the plug out of the socket. Make sure that all moving parts have reached a complete
standstill:
- before you dislodge any blockages or clogs in the chute.
- before carrying out any checks, cleaning, maintenance or other work on the lawn mower.
- if you have struck a foreign object. Examine the mower for signs of damage and carry out any necessary repairs before
restarting and continuing to work with the mower.
- if the lawn mower begins to experience exceptionally strong vibrations, immediately switch it off and check it.
- Search for damage.
- Repair the damaged parts as required.
- Make sure that all nuts, bolts and screws are fastened securely.
q) Switch off the mower and pull the plug whenever you leave the mower.
Maintenance and storage
a) Make sure that all nuts, bolts and screws are tightened securely and that the machine is in safe working condition.
b) Allow the mower to cool before you put it into an enclosed area.
c) To avoid the risk of re, keep the motor housing and ventilation slots clear of grass, leaves, oil and grease.
d) Routinely check the grass basket for signs of wear and impaired functionality.
e) For your own safety, have worn or damaged parts replaced without delay.
f) Take care not to jam your ngers between moving cutting tools and stationary parts of the equipment while you are
adjusting the equipment.
g) While you are carrying out maintenance work on the cutting tools, remember that the cutting tools can still be moved
even if the power source has been switched off .
h) For your own safety, replace worn or damaged parts without delay. Use only original spare parts and original
accessories.
Ozito Industries will not be responsible for any damage or injuries
caused by repair of the tool by an unauthorised person or mishandling
or mistreatment of the tool. This tool is designed for Domestic Home Use
only. Use in commercial or industrial environments will void the warranty.
CAUTION!: ALWAYS HANDLE THE BLADE WITH CARE
– SHARP EDGES COULD CAUSE SERIOUS INJURY.
USE GLOVES.
MAINTENANCE
WARNING!: BEFORE CLEANING YOUR ECOMOW
ELECTRIC MOWER OR CARRYING OUT ANY
MAINTENANCE PROCEDURE, MAKE SURE THAT THE
MOTOR IS OFF AND THE TOOL DISCONNECTED FROM
THE POWER SUPPLY TO PREVENT ACCIDENTAL
STARTING.
Removing the Blade
1. To remove the blade bolt, hold the
blade rmly and with a 13mm socket
(not supplied) loosen the blade bolt
by turning it anti-clockwise.
Note: A piece of timber will assist in
holding the blade while removing or
tightening the blade bolt.
2. Remove the blade bolt and blade.
3. Inspect for damage and clean as
necessary.
Replace the metal blade after 50 hours mowing or 2 years whichever is
the sooner – regardless of condition. If the blade is cracked or damaged
replace it with a new one. Never use a blade bolt if the insulated head is
damaged, cracked or missing.
TIMBER
Fitting the Blade
• Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safe
working condition.
• Check the catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety.
• Only use the replacement blade, blade bolt, and impeller specied for this
product.
• Be careful during adjustments of the lawn mower to prevent entrapment of
the ngers between moving blade and xed parts of the machine.
• Oil the wheel pins.
• When not in use, the mower should be stored in a dry, frost-free location, out
of reach of children.If the housing of the mower requires cleaning, do not use
solvents but a moist soft cloth and brush only.
• Frequently check the wheel threads are rm and tight.
CAUTION!: DO NOT TOUCH ROTATING BLADES.
ADDITIONAL SAFETY INSTRUCTIONS FOR LAWN MOWERS
1. Fit the blade to the fan with the tilt edges of the blade facing towards the
mower, ensuring the blade is located onto the fan location lugs correctly.
2. Re-assemble blade bolt through blade and fan.
3. Hold the blade rmly and tighten blade bolt with a (not supplied), by turning
in a clockwise direction. The tightening torque should be approx. 25 Nm.
ozito-diy.co.uk
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the customer
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectication of said
defects on the product or the replacement of the product, whichever we
prefer.
Please note that our devices are not designed for use in commercial, trade
or professional applications. A guarantee contract will not be created if the
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Warranty
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts tted. This also applies if an on-site service is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR
REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk
WARRANTY
0917
SPARE PARTS
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse or Homebase
store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: info@ozito-diy.co.uk
WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of re, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,
before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
Before you connect the equipment to the mains supply make sure that the data on the rating plate are
identical to the mains data.
This tool is double insulated therefore no earth wire is required.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid
a hazard.
Note: Double insulation does not take the place of normal safety precautions when operating this tool. The
insulation system is for added protection against injury resulting from a possible electrical insulation failure
within the tool.
Using an Extension Lead
Please only use power cables that are not damaged. The total length of the power cable should not exceed
40 meters; going beyond this distance will reduce the power output of the electric motor. The power cable
must have a cross-section of 3 x 1.5 mm2. The insulating sheath of lawn mower power cables is frequently
damaged.
Some of the causes for this are:
• Cuts caused by running over the cable
• Pinching when the power cable is dragging under doors and pulled through windows.
• Cracking due to old age of the insulation
• Kinking by improperly fastening or guiding the power cable.
The power cables must, at the very minimum, be of type HO5RN-F and 3-stranded. The cable type must
be printed somewhere on the power cable. Only purchase power cables that are marked as such! Plugs
and socket couplers for the power cables must be made from rubber and be splash proof. There is a limit to
how long power cables can be. Longer power cables require larger conductor cross-sections. Power cables
and connecting lines must be regularly checked for damage. Ensure that the lines are de-energized before
checking them. Completely unwind the power cable. Also check power cable entry points, plugs and socket
couplers for kinks.
ELECTRICAL SAFETY
DESCRIPTION OF SYMBOLS
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! “Read all safety warnings, instructions, illustrations and specications provided
with this power tool.” Failure to follow the warnings and instructions may result in electric shock,
re and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the
warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power
tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and
ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualied repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
SERVICE INFORMATION
Please note that the following parts of this product are subject to normal
or natural wear and that the following parts are therefore also required
for use as consumables.
* Not necessarily included in the scope of delivery!
Category Example
Wear parts* Carbon brushes, V-belt
Consumables* Blade
Missing parts
DECLARATION OF CONFORMITY
Gao/Product-ManagementWeichselgartner/General-Manager
explains the following conformity according to EU directives and norms for
the following product
Electric Lawn Mower ELM-1030U (Ozito)
2014/29/EU
2005/32/EC_2009/125/EC
2014/35/EU
2006/28/EC
X 2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X 2011/65/EU
X 2006/42/EC
Annex IV
Notied Body:
Notied Body No.:
Reg. No.:
X 2000/14/EC_2005/88/EC
Annex V
X Annex VI
Noise: measured LWA = 93 dB (A); guaranteed LWA = 96 dB (A)
P = 1 KW; L/Ø = 30 cm
Notied Body: Société Nationale de Certication et DʼHomologation
S.A.R.L. (SNCH) (0499)
2012/46/EU
Emission No.:
Standard references: EN 60335-2-77; EN 62233;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 11.09.2017
First CE: 17 Archive-File/Record: NAPR017645
Art.-No.: 30.001.97 I.-No.: 11017 R. GehardDocuments registrar:
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric
and electronic equipment and its implementation in national laws, old
electric power tools have to be separated from other waste and disposed
of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the
owner of the electrical equipment must make sure that the equipment is
properly disposed of if p1-he no longer wants to keep the equipment. The old
equipment can be returned to a suitable collection point that will dispose
of the equipment in accordance with the national recycling and waste
disposal regulations. This does not apply to any accessories or aids
without electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of
documentation and papers accompanying products is permitted only with
the express consent of the iSC GmbH.
Subject to technical changes.
Danger!
Sound and vibration
Sound and vibration values were measured in accordance
with the standards EN ISO 3744: 1995, EN ISO 11201: 1995, and EN ISO
20643: 2005.
Lpa at the operator position: 80.4 dB
Kpa uncertainty: 3 dB
Lwa sound power level 96 dB
Kwa uncertainty: 3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions) determined in
accordance with EN 60745.
Vibration at the handles
Vibration emission value a
h = 2.285 m/s2
K uncertainty = 1.5 m/s2
Keep the noise emissions and vibrations to a minimum.
• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Danger! Read the directions for use before
operating the equipment.
Caution! Keep all other persons a y from the wa
danger zone.
Caution! Sharp blades! Pull out the safety plug before
carrying out any repair work or if the p er cable is ow
damaged. The blades will continue to rotate after the motor
is switched off.
Caution! Keep the power cable a y from the cutters! wa
Guaranteed sound p er level: 96 dBow
Danger! Read the operating instructions to reduce the risk of injury
Protection class II
ADDITIONAL INFORMATION
Only replace the blade with a genuine Ozito replacement blade, as this will
ensure top performance and safety under all conditions.
TROUBLESHOOTING
Problem Cause Remedy
The motor
fails to start
The capacitor is
defective
The mower housing is clogged.
Have repaired by the Customer
Service Centre
There is no electricity
at the plug
Check the cable and the fuse
The cable is defective Check the cable
The combined switch/
plug is defective
Have repaired by the Customer
Service Centre
The connectors have
become separated
from the motor or the
capacitor
Have repaired by the Customer
Service Centre
The mower is standing
in high grass
Start in low grass or on an area
that has already been mowed;
change the cutting height if
necessary
Start in low grass or
on an area that has
already been mowed;
change the cutting
height if necessary
Clean the housing so that the
blade moves freely
The motor
performance
drops
The grass is too high
or too damp
Correct the cutting height
The mower housing is
clogged
Clean the housing
The blade is severely
worn
Replace the blade
Cutting is
irregular
The blade is worn Replace or re-sharpen the blade
Wrong cutting height Correct the cutting height
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
KNOW YOUR PRODUCT SETUP & PREPARATION
1. Motor cover
2. Lifting handle
3. Lower handle
4. Safety switch
5. Start/stop lever
6. Handle knobs
7. Grass catcher ap
8. Grass catcher
9. Handle securing set
10. Upper handle
2. ASSEMBLY 5. HOW TO MOW
ECOMOW ELECTRIC MOWER
To obtain the desired cutting height, the front and rear axles are
repositioned on the underside of the mower housing.
1. Press and hold the lock-off
button.
1
9 10
2 3 4
67 8
• Always use an approved extension lead suitable for power input
of this tool.
• Heavy duty power leads recommended not exceding 25m.
• While using your lawn mower always wear substantial footwear
and long trousers.
• Make sure the lawn is clear of sticks, stones, wire and debris;
they could be thrown by the blade.
• Before using the lawn mower and after any impact, check for
signs of wear or damage and repair as necessary.
• Replace a worn or damaged blade together with the blade bolt to
preserve balance.
5
WARNING!: ENSURE THE TOOL IS DISCONNECTED
FROM THE POWER SUPPLY BEFORE ASSEMBLY.
Fitting the Lower Handle to Mower Body
1. Fit the lower handle onto the
threaded ends.
1. First t the cord retainer, slide
it over the upper handle end
before xing the upper handle
to the lower handles.
1. Secure the power cord from the
switch housing to the mower using
cable ties (supplied).
To prevent accidental start up of the motor the mower is tted with a
dual action switch
2. To assemble the grass catcher
align the two halves and push
them together, one side at a
time. Ensure the two halves click
together around the entire middle
section.
1. Assemble the grass catcher
handle onto the opening
on the top half of the grass
catcher. The handle will click
into position when aligned
and tted correctly.
WARNING!: WHEN ASSEMBLING THE GRASS
CATCHER BACK TO THE MOWER AFTER
EMPTYING, ALWAYS ENSURE THERE IS NO BUILD
UP OF GRASS IN THE GRASS CHUTE. IF NEEDING TO
CLEAR THE GRASS, ALWAYS ENSURE THE MOWER
IS DISCONNECTED FROM THE POWER SUPPLY
PRIOR TO CLEARING. A BUILD UP OF GRASS IN THE
GRASS CHUTE MAY PREVENT GRASS FROM MOVING
INTO THE GRASS CATCHER EFFECTIVELY.
WARNING!: DISCONNECT THE MOWER FROM
THE POWER SUPPLY AND ENSURE THE BLADE
HAS STOPPED COASTING BEFORE ADJUSTING THE
HEIGHT.
Securing the Power Cord to the Handles
Assembling the Grass Catcher
“CLICK”
“CLICK”
“CLICK”
Fitting and Removing Grass Catcher
3. ADJUSTMENTS
Cutting Height Adjustment
4. SWITCHING ON/OFF
Start mowing the edge of the lawn
nearest to the power point so the
lead is laid out on the lawn you have
already cut.
For optimum grass collection, always mow in a straight line; do
not swing the lawn mower from side to side.
Mowing long thick grass may cause the motor speed to drop; you will
hear a change in the motor sound. If the motor speed drops you may
overload your lawn mower, which may cause damage. When mowing
in long thick grass rst cut with the cutting height set in the highest
position, this will help reduce the load.
Do Not Overload the Mower
Fitting the Upper Handle to the Lower Handle
3. To empty the grass catcher, lift
the catcher ap with one hand
then lift the grass catcher with
the other hand up off the two
raised housing clips.
The catcher must be attached to the two raised hooks on the mower.
1. Lift up the catcher ap with one
hand and guide the catcher over
the two hooks on the mower
housing.
2. Lower the grass catcher in place
and lower the catcher ap. The
catcher ap is held against the
gass catcher by a spring
WARNING! KEEP
POWER CORD AWAY
FROM BLADES.
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
WE RECOMMEND THE USE OF A RESIDUAL CURRENT
DEVICE (RATED 30mA OR LESS).
1
2. Pull the Start/stop lever towards
the handle and hold in position,
the motor will now start.
3. Release the lock-off button
4. Release the Start/stop lever to
stop the mower.
1. Place the mower on its side.
2. Pull the wheel axle towards
the front of the mower.
3. Locate the wheel axle into
the desired cutting height
adjustment position.
2
2. Fit and secure in place with
the lower handle knobs.
Note: Make sure that front, back,
left & right wheels are located in
the same cutting height adjustment
position.
1
2
3
Cutting Height Positions
1 - 30mm (lowest).
2 - 50mm.
3 - 70mm (highest).
2. Place the upper handle over
the upper ends of the lower
handle. From the handle
securing set, t the bolts
through the inner side of
the lower handle and then
through the holes in the upper
handle. Secure in place by
screwing the handle securing
knobs over the protruding
ends of the bolts.
WARNING! THE BLADE WILL STOP A FEW
SECONDS AFTER THE SWITCH HAS BEEN
RELEASED. BE AWARE OF THE NECESSARY TIME IT
TAKES FOR THE BLADE TO STOP. DO NOT ATTEMPT
TO STOP THE BLADE.
Overload Protection
The mower has an internal cut off switch which will stop the operation
of the motor temporarily if too high in temperature. This cut off switch
will suddenly stop the motor from operating should the motor become
too hot during the operation of the mower.
First disconnect the mower from the power supply and inspect blade
for any obstructions.
A wait of 10 minutes in cooling time, or longer depending on ambient
temperature and the operation being performed, before switching On
the mower and resuming normal operation.
ELM-1030U
1. BEFORE USE
Items Supplied
Please check that the article is complete as specied in the scope of delivery.
If parts are missing, please contact our service centre or the sales outlet
where you made your purchase at the latest within 5 working days after
purchasing the product and upon presentation of a valid bill of purchase.
Also, refer to the warranty table in the service information at the end of the
operating instructions.
• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation
braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.
Danger!
The equipment and packaging material are not toys. Do not let children
play with plastic bags, foils or small parts. There is a danger of
swallowing or suffocating!
Proper Use
The lawn mower is intended for private use i.e. for use in home and
gardening environments.
Private use of the lawn mower refers an annual operating time generally not
exceeding that of 50 hours, during which time the machine is primarily used
to maintain small-scale, residential lawns and home/hobby gardens. Public
facilities, sporting halls, and agricultural/forestry applications are excluded.
Important. Due to the high risk of bodily injury to the user, the lawn mower
may not be used to trim bushes, hedges or shrubs, to cut scaling vegetation,
planted roofs, or balcony-grown grass, to clean (suck up) dirt and debris
off walkways, or to chop up tree or hedge clippings. Moreover, the lawn
mower may not be used as a power cultivator to level out high areas such as
molehills.
For safety reasons, the lawn mower may not be used as a drive unit for other
work tools or toolkits of any kind, unless they have been expressly permitted
by the manufacturer.
The equipment is to be used only for its prescribed purpose. Any other use is
deemed to be a case of misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial,
trade or industrial applications. Our warranty will be voided if the machine is
used in commercial, trade or industrial businesses or for equivalent purposes.
Caution!
Residual risks
Even if you use this electric power tool in accordance with instructions,
certain residual risks cannot be rules out. The following hazards may
arise in connection with the equipment’s construction and layout:
1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the equipment is used
over a prolonged period or is not properly guided and maintained.
Warning!
This equipment generates an electromagnetic eld during
operation. Under certain circumstances this eld may actively or
passively impede medical implants. To reduce the risk of serious
or fatal injuries, we recommend persons with medical implants to
consult their doctor and the manufacturer of the medical implant
prior to using the equipment.
OPERATION

Product specificaties

Merk: Ozito
Categorie: Grasmaaier
Model: ELM-1030U

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito ELM-1030U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Grasmaaier Ozito

Ozito

Ozito CPM-300C Handleiding

10 December 2024
Ozito

Ozito PXBMK-4047SP Handleiding

16 Maart 2024
Ozito

Ozito ELM-1230 Handleiding

20 Juni 2023
Ozito

Ozito ESA-1231U Handleiding

18 Juni 2023
Ozito

Ozito PXCLMK-218U Handleiding

11 Juni 2023
Ozito

Ozito PXCLMK-1318EU Handleiding

8 Juni 2023
Ozito

Ozito PXCSDMK-418U Handleiding

8 Juni 2023
Ozito

Ozito PXCLMK-418U Handleiding

8 Juni 2023
Ozito

Ozito LMPC-301U Handleiding

5 Juni 2023
Ozito

Ozito ELM-1250U Handleiding

2 Juni 2023

Handleiding Grasmaaier

Nieuwste handleidingen voor Grasmaaier

Powerblade

Powerblade 350CX Handleiding

10 December 2024
Powerblade

Powerblade V475 Handleiding

10 December 2024
Stihl

Stihl RM 253 Handleiding

8 December 2024
Baumr-AG

Baumr-AG 790SXe Handleiding

7 December 2024
Baumr-AG

Baumr-AG 730EX Handleiding

7 December 2024
Bavaria

Bavaria BPM 46 SD Handleiding

5 December 2024
Bavaria

Bavaria BPM 46 S Handleiding

5 December 2024
Bavaria

Bavaria BPM 46 Handleiding

5 December 2024
Flymo

Flymo Chevron 37C Handleiding

5 December 2024
Flymo

Flymo Lawnrake Compact 3400 Handleiding

5 December 2024