Ozito DP-350U Handleiding

Ozito Boormachine DP-350U

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito DP-350U (3 pagina's) in de categorie Boormachine. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

size 445 x 210 mm

Danger! - Read the operating instructions to re-

duce the risk of inquiry

Caution! Wear ear-mus. The impact of noise

can cause damage to hearing.

Caution! Wear safety goggles. Sparks gene-

rated during working or splinters, chips and dust

emitted by the device can cause loss of sight.

The reprinting or reproduction by any other me-

ans, in whole or in part, of documentation and

papers accompanying products is permitted only

with the express consent of the iSC GmbH.

Subject to technical changes

DP-350U

GB Additonal operating & safety instructions Drill Press

Service information

We have competent service partners in all countries named on the guarantee certicate whose contact

details can also be found on the guarantee certicate. These partners will help you with all service re-

quests such as repairs, spare and wearing part orders or the purchase of consumables.

Please note that the following parts of this product are subject to normal or natural wear and that the

following parts are therefore also required for use as consumables.

Category Example

Wear parts* Keyed chuck

Consumables* Drill Bits

Missing parts

* Not necessarily included in the scope of delivery!

In the eect of defects or faults, please register the problem on the internet at www.isc-gmbh.info. Plea-

se ensure that you provide a precise description of the problem and answer the following questions in all

cases:

• Did the equipment work at all or was it defective from the beginning?

• Did you notice anything (symptom or defect) prior to the failure?

• What malfunction does the equipment have in your opinion (main symptom)?

Describe this malfunction.

Yang/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Drill Press DP-350U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

2014/35/EU

2006/28/EC

X 2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X 2011/65/EU

X 2006/42/EC

Annex IV

Noti ed Body:

Noti ed Body No.:

Reg. No.:

2000/14/EC_2005/88/EC

Annex V

Annex VI

Noise: measured LWA = dB (A); guaranteed LWA = dB (A)

P = KW; L/Ø = cm

Noti ed Body:

2004/26/EC

Emission No.:

Standard references: EN 61029-1; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3

Landau/Isar, den 09.06.2016

First CE: 16 Archive-File/Record: NAPR014342

Art.-No.: 44.722.29 I.-No.: 11016 R. GehardDocuments registrar:

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Declaration of conrmity

size 445 x 210 mm

Items supplied

Please check that the article is complete as

specied in the scope of delivery. If parts are

missing, please contact our service center or the

sales outlet where you made your purchase at

the latest within 5 working days after purchasing

the product and upon presentation of a valid bill

of purchase. Also, refer to the warranty table in

the service information at the end of the operating

instructions.

• Open the packaging and take out the equip-

ment with care.

• Remove the packaging material and any

packaging and/or transportation braces (if

available).

• Check to see if all items are supplied.

• Inspect the equipment and accessories for

transport damage.

• If possible, please keep the packaging until

the end of the guarantee period.

Danger!

The equipment and packaging material are

not toys. Do not let children play with plastic

bags, foils or small parts. There is a danger of

swallowing or suocating!

Proper use

This pillar drill is designed for drilling metal, pla-

stic, wood and similar materials. It is intended for

use in the private sector only. Food and harmful

materials may not be processed with the equip-

ment. The drill chuck is only designed for use with

drill bits and tools with a shaft diameter of 1.5 to

13 mm, and for cylindrical tool shanks. Tools with

a tapered shank can also be used. The equip-

ment is intended for use by adults only.

The equipment is to be used only for its prescri-

bed purpose. Any other use is deemed to be a

case of misuse. The user / operator and not the

manufacturer will be liable for any damage or inju-

ries of any kind caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

Technical data

Nominal input voltage 230-240V ~ 50 Hz ..............

Power rating ................................................350 W

Operating mode S2 15 min. ...................................

No load speed 580 - 2.650 rpm .............................

Speed levels 5 .......................................................

Keyed chuck Ø 1.5 - 13 mm ..................................

Spindle shaft to column distance 104 mm .............

Spindle travel 50 mm .............................................

Column height..........................................395 mm

LpA sound pressure level 62 dB(A) .........................

LWA

sound power level 75 dB(A) .............................

KpA uncertainty 3 dB ..............................................

KWA uncertainty 3 dB .............................................

Sound and vibration

Sound and vibration values were measured in

accordance with EN 61029.

Load factor:

A load factor of S2 15 min (intermittent periodic

duty) means that you may operate the motor con-

tinuously at its nominal power level (350 W) for no

longer than the time stipulated on the specica-

tions label (15 minutes ON period).

If you fail to observe this time limit the motor will

overheat. During the OFF period the motor will

cool again to its starting temperature.

The specied vibration value was established in

accordance with a standardized testing method. It

may change according to how the electric equip-

ment is used and may exceed the specied value

in exceptional circumstances.

The specied vibration value can be used to

compare the equipment with other electric power

tools.

The specied vibration value can be used for initi-

al assessment of a harmful eect.

Keep the noise emissions and vibrations to a

minimum.

• Only use appliances which are in perfect wor-

king order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever

necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Caution!

Residual risks

Even if you use this electric power tool in ac-

cordance with instructions, certain residual

risks cannot be rules out. The following ha-

zards may arise in connection with the equip-

ment’s construction and layout:

1. Lung damage if no suitable protective dust

mask is used.

2. Damage to hearing if no suitable ear protecti-

on is used.

3. Health damage caused by hand-arm vibra-

tions if the equipment is used over a pro-

longed period or is not properly guided and

maintained.

For EU countries only

Never place any electric power tools in your

household refuse.

To comply with European Directive 2012/19/EC

concerning old electric and electronic equipment

and its implementation in national laws, old elec-

tric power tools have to be separated from other

waste and disposed of in an environment-friendly

fashion, e.g. by taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to

the manufacturer, the owner of the electrical

equipment must make sure that the equipment

is properly disposed of if he no longer wants to

keep the equipment. The old equipment can be

returned to a suitable collection point that will

dispose of the equipment in accordance with the

national recycling and waste disposal regulations.

This does not apply to any accessories or aids

without electrical components supplied with the

old equipment.

Product specificaties

Merk:	Ozito
Categorie:	Boormachine
Model:	DP-350U

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito DP-350U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Boormachine Ozito

Ozito BDP-450 Handleiding

26 Juli 2023

Ozito HDR-1050U Handleiding

30 Juni 2023

Ozito HDR-3000U Handleiding

19 Juni 2023

Ozito HDR-1100U Handleiding

14 Juni 2023

Ozito PXBHS-100U Handleiding

14 Juni 2023

Ozito PXHDS-301U Handleiding

14 Juni 2023

Ozito HDR-5000U Handleiding

14 Juni 2023

Ozito DP-350U Handleiding

8 Juni 2023

Ozito PXDDS-201U Handleiding

24 Mei 2023

Ozito LCD-2050U Handleiding

23 Mei 2023

Handleiding Boormachine

Nieuwste handleidingen voor Boormachine

Black Decker 1963 Handleiding

8 December 2024

Black Decker 1350-09 Handleiding

8 December 2024

Gude GTB 16/5 R Handleiding

8 December 2024

Hikoki DV36DA Handleiding

7 December 2024

Hikoki DH26PC2 Handleiding

7 December 2024

Hikoki DH28PCY2 Handleiding

7 December 2024

Zipper ZI-BHA1500DN Handleiding

7 December 2024

Bavaria BRH 850 Handleiding

5 December 2024

Bavaria BCD 18/1 2B Handleiding

5 December 2024

Bavaria BCD 14,4 Li Handleiding

5 December 2024