OSD Audio VMS100 Handleiding

OSD Audio Controller VMS100

Lees hieronder de 📖 handleiding in het Nederlandse voor OSD Audio VMS100 (1 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

L+ L- R- R+

INPU T OU TPU T

L+ L- R- R+

L+ L- R- R+L+ L- R- R+

RECEIVER/AMPLIFIER

SPEAKER OUTPUTS

L+ L- R - R+

2x 4x 8x 16x

No. of 8 ohm pairs

Switch Settings

1-2 3-4 5-8 9-16

2x 4x 8x 16x

Installation Instruction for the VMS-100

The VMS-100 is simple to install. Pay attention to the following steps:

- Red/Black = right speaker Red = positive [ + ] Black = ground [ - ]

- White/Green = left speaker White = positive [ + ] Green = ground [ - ]

OSD AUDIO • 1405 Pioneer Street • Brea • CA 92821 • www.osdaudio.com

A U D I O

OSD

To prevent from overloading

and damaging the amplifier,

the switch must be set

correctly to match the

impedance of the speaker

system to a level equal to or

greater than the impedance

of the amplifier.

Find out the minimum impedance of the amplifier. This

information may be found in the manual or on the back of

amplifier, near the speaker terminals. It is measured in

ohms.

Determine the correct switch setting using the chart

below.

Figure out the total number of speaker pairs to be used.

Set the switch. Make sure that each volume control’s

switch setting is consistent throughout the whole system.

Make sure to use the integral strain reliefs where appropriate when

routing the cable in the J-box.

Strip the insulation off the end of each of the eight individual wires

( four from the amplifier and four to the speakers ) at about 1/4”.

Twist exposed ends together.

Connect the speakers wires to the connector labeled Output

L [ + , - ] and R [ + , - ]. Speaker wires typically use the

following color configuration.

Insert the volume control into the J-box. Mount carefully, making

sure that no wires are pinched or shorted.

VMS-100 Slider

Impedance Matching Slider Stereo Volume Control

Mark the input and output cables accordingly for easy installation.

OSD Audio will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts,

free of charge in the USA, for five years from the date of original purchase. This warranty does not cover damages in shipment, failures caused by

other products not supplied by OSD Audio or failures due to accident, misuse, or alteration of the equipment. This warranty is extended only to the

original purchaser, and a purchase receipt, invoice, or other proof or original purchase date will be required before warranty repairs are provided.

Mail in service can be obtained during the warranty period by emailing RMA@osdaudio.com. A Return Authorization (RMA) number must be

obtained in advance and be marked on the outside of the shipping carton.

This warranty gives you specific legal rights, and may have other rights ( which vary from state to state ). If a problem with this product develops

during or after the warranty period please contact OSD Audio, your dealer, or any factory-authorized service center.

OSD Audio Limited Warranty

Connect the leads from amplifier to the volume control connector

according to the labeled Input L [ + , - ] and R [ + , - ].

2x 4x 8x 16x

INPU T

L+ L- R- R+

OUT PU T

L+ L- R- R+

Input

Out p ut

Product specificaties

Merk:	OSD Audio
Categorie:	Controller
Model:	VMS100
Kleur van het product:	Wit
Soort:	Schuifvolumeregelaar
Impedantie:	16 Ohm
Afmetingen (B x D x H):	635 x 412 x 635 mm
Power handling:	100 W
Verzachtingsstappen:	12