Orion WB-4780 Handleiding

Orion Niet gecategoriseerd WB-4780

Lees hieronder de 📖 handleiding in het Nederlandse voor Orion WB-4780 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Tilt adjusting knob
INSTALLATION INSTRUCTIONS
ISSUED: OCT.2012
7
Tilting Wall Mount
4. Adjustment
3. Hang Display onto the Wall Plate
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
75kg
(165lbs)
MAX
Loose the adjusting knobs to tilt desired angle then tighten them.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
WB-4780
400x400/600x400
800x400/800x600 70"
MAX
0°
-10°
wall
Tighten bottom bolts to secure display brackets to the wall plate.
wall
Bolt
Premium Mount Inc
7300 Bolsa Ave., Westminster, CA 92683 -
Phone: 714-766-6303
2
Component Checklist
IMPORTANT: Ensu re tha t you ha ve rec eived all pa rts according to t he compon ent checklist pr ior to installin g. If
any parts are missing or f aulty, telephone your local distributor f or a replacement .
Package M
Package W
ST6.3x55 (x6)
W-A
concrete anchor (x6)
W-B
D6 washer (x6)
W-C
1
NOTE: Read the entire instruction manual before you start installation and assembly.
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experience and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of a stud finder is highly recommended.
• Always use assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
wall plate
A
(x1)
M5x14 (x4)
M-A
M6x14 (x4)
M-B
washer
M-F
(x4)
M8x20 (x4)
M-C
big spacer (x4)
M-H
M6x30 (x4)
M-D
M8x30 (x4)
M-E
small spacer (x8)
M-G
left (x1)adapter bracket
B
right (x1)adapter bracket
C
4
3
WARNING
• Make sure that mounting screws are anchored into the center of the studs. The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
1a. Mount on Wood Stud Wall
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting be used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installers must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
1b. Mount on Solid Brick and Concrete Block
W-C
Screw the wall
plate onto
the wall
Drill pilot holes
X X
√
1
2
3
Find and mark the
exact location of
mounting holes
ø 4.5mm
(ø 3/16")
55mm
(2.2")
55mm
55mm
55mm
55mm
2
2
2
2.
.
.
.2
2
2
2"
"
"
"
(
(
(
()
)
)
)
55mm
(2.2" )
X X
√
Screw the wall
plate onto
the wall
Drill pilot holes
1
2
Mark the exact
location of
mounting holes
60mm
(2.4")
60mm
60mm
60mm
60mm
2
2
2
2.
.
.
.4
4
4
4"
"
"
"
(
(
(
()
)
)
)
60mm
(2.4")
ø 10mm
(ø 3/8" )
W-A
W-C
W-B W-A

Product specificaties

Merk: Orion
Categorie: Niet gecategoriseerd
Model: WB-4780

Heb je hulp nodig?

Als je hulp nodig hebt met Orion WB-4780 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Orion

Orion

Orion 24RPE Handleiding

24 Augustus 2024
Orion

Orion 22RPE Handleiding

24 Augustus 2024
Orion

Orion OR22RPE Handleiding

25 Maart 2024
Orion

Orion WB-4780 Handleiding

25 Maart 2024
Orion

Orion CMA-02 Handleiding

25 Maart 2024
Orion

Orion WB-31 Handleiding

25 Maart 2024
Orion

Orion OR24RPE Handleiding

25 Maart 2024
Orion

Orion WBLS Handleiding

28 Oktober 2023
Orion

Orion 8FIDKR Handleiding

28 Oktober 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Xblitz

Xblitz R8 Power Charge Handleiding

3 December 2024
Xblitz

Xblitz R4 Power Handleiding

3 December 2024
Franke

Franke Urban UBG 610-78 Handleiding

3 December 2024
Franke

Franke ANX211RHD Handleiding

3 December 2024
Franke

Franke ANX220 Handleiding

3 December 2024
Dell

Dell NX3330 Handleiding

3 December 2024
Dell

Dell PowerConnect B-DCX-4s Handleiding

3 December 2024
Hager

Hager AKB83000701 Handleiding

3 December 2024
Hager

Hager AKB81500402 Handleiding

3 December 2024
Hager

Hager AKBA1500401V Handleiding

3 December 2024