Oregon Scientific RMR382 Handleiding

Oregon Scientific Weerstation RMR382

Lees hieronder de 📖 handleiding in het Nederlandse voor Oregon Scientific RMR382 (2 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Wireless Indoor / Outdoor Thermometer

with Self-Setting Atomic Clock

Model: RMR382A

USER MANUAL

INTRODUCTION

Thank you for selecting the Oregon Scientiﬁc

TM Wireless

Indoor / Outdoor Thermometer with Self- Setting Atomic

Clock. The main unit can suppor t up to 3 sensors. To

purchase additional sensors, please contact your local

retailer.

NOTE Please keep this manual handy as you use

your new product. It contains practical step-by-step

instructions, as well as technical speciﬁcations and

warnings you should know about.

OVERVIEW

FRONT VIEW

1. Channel number and sensor reception status

2. Sensor low batter y warning

3. Maximum / minimum outdoor temperature reading

4. Indoor temperature display icon

5. Main unit low battery warning

6. Maximum / minimum indoor temperature reading

7. Alarm is set

8. 12-hour clock

9. Alarm is displayed

10. Radio-controlled clock reception icon

11. Hi / lo alarm is displayed

12. Outdoor temperature trend icon

13. Ice warning is active

14. Outdoor temperature reading

15. Indoor temperature trend icon

16. Indoor temperature reading

17. US time zones

18. Time, alarm and date

19. ALARM : View alarm status; set alarm

BACK VIEW

1. / Increase / decrease setting; activate / :

deactivate clock reception signal

2. Change settings / displayMODE:

3. CHANNEL: Switch remote sensor display

4. MEM: View current, maximum and minimum

temperature

5. °C / °F: Select temperature unit °C / °F

6. TEMP HI / LO Change settings or enable / :

disable hi or lo temperature alarm for channel 1

7. RESET: Reset unit to default settings

8. ZONE: Toggle between the 4 US time zones

9. Battery compartment

REMOTE SENSOR (THN132N)

1. LED indicator 1. Wall mount

2. Battery compartment

3. Battery door

4. Table stand

5. hole RESET

6. switchCHANNEL

GETTING STARTED

POWER

Insert batteries before ﬁrst use, matching the polarity

(+ and -).

NOTE Install batteries in the remote sensor before the

main unit. Press RESET after each battery change. Do not

use rechargeable batteries. We recommend that you use

alkaline batteries with this product for longer usage and

lithium batteries in temperatures below freezing.

shows when batteries are low.

UNIT LOCATION

Main Indoor temperature area

Remote Outdoor temperature area

REMOTE SENSOR

The sensor collects temperature readings approx. every

40 seconds and sends them to the main unit. The main

unit can collect data from up to 3 sensors.

To set up the sensor:

1. Slide open the battery door.

2. Insert the batteries, matching the polarity (+ / -).

Reset after each battery change.

3. Select a channel. Make sure you use a different

channel for each sensor.

4. Close the battery compartment.

5. Secure the sensor in the desired location using the

wall mount or table stand.

For best results:

• Place the sensor out of direct sunlight and moisture.

• Do not place the sensor more than 30 meters (100

feet) from the main (indoor) unit.

• Position the sensor so that it faces the main (indoor)

unit, minimizing obstructions such as doors, walls, and

furniture.

• Place the sensor in a location with a clear view to the

sky, away from metallic or electronic objects.

• Position the sensor close to the main unit during cold

winter months as below-freezing temperatures may

affect battery performance and signal transmission.

The transmission range may vary depending on many

factors. You may need to experiment with various

locations to get the best results.

Standard Alkaline batteries contain signiﬁcant amounts of

water. Because of this they will freeze in low temperatures

of approximately -12°C (10°F). Disposable Lithium

batteries have a much lower threshold for temperature

with an estimated freezing range of below -30°C

(-22°F).

Wireless ranges can be impacted by a variety of factors

such as extremely cold temperatures. Extreme cold may

temporarily reduce the effective range between the sensor

and the base station. If the unit’s performance fails due to

low temperature, the unit will resume proper functioning

as the temperature rises to within the normal temperature

range (i.e. no permanent damage will occur to the unit due

to low temperatures).

SENSOR DATA TRANSMISSION

The reception icon in the outdoor temperature area shows

the status.

ICON DESCRIPTION

Main unit is searching for the

sensor(s)

A channel has been found and

sensor signal is being received

The sensor cannot be found.

Search for the sensor or check

batteries

To search for a sensor:

Simultaneously, press and hold MEM CHANNEL and

for 2 seconds.

NOTE If the sensor is still not found, check the batteries,

obstructions, and remote unit location.

CLOCK

CLOCK RECEPTION

This product is designed to synchronize its date and time

automatically once it is within range of the WWVB-60

signal from the atomic clock in Fort Collins, Colorado.

The clock collects the radio signals whenever it is within

3218 km (2000 miles) of a signal.

NOTE Initial reception takes 2-10 minutes for ﬁrst set up

or when RESET is pressed. Once complete, the reception

icon will stop blinking. If the signal is weak, it can take up to

24 hours to get a valid signal.

RECEPTION SIGNAL

STRONG WEAK NO SIGNAL

To enable and force a signal search:

Press and hold for 2 seconds.

To disable the signal reception:

Press and hold for 2 seconds.

SET CLOCK

If the clock signal reception is enabled and a signal is

being received the clock does not need to be manually

set.

To manually set the clock:

1. Press and hold MODE for 2 seconds.

2. Press and to change the settings.

3. Press MODE to conﬁrm.

4. The setting sequence is: 12 / 24 hour format, hour,

minute, year, date / month format, month, date, and

display language.

and “- -.-”(Outdoor

temperature area)

1 2 3

RMR382A 086L004376-010_R1.indd 1 4/3/06 10:32:05 AM

NOTE Press ZONE to set the US time zone options: (P)

Paciﬁc, (M) Mountain, (C) Central and (E) Eastern.

NOTE The language options are (E) English, (F) French,

(D) German, (I) Italian, and (S) Spanish.

To switch the clock display:

Press to toggle between:MODE

• Clock with seconds

• Clock with day

• Calendar

ALARM

To set the alarm:

1. Press ALARM to view the alarm. will show on the

display.

2. Press and hold ALARM for 2 seconds.

3. Press or to change the hour / minute settings.

4. Press to conﬁrm.ALARM

To activate or deactivate the alarm:

Press when in the alarm display. appears ALARM

when the alarm is set.

To silence the alarm and reset it for the next day:

Press .ALARM

TEMPERATURE

To toggle the temperature unit:

Press .°C / °F

To view outdoor sensor temperature readings:

Press . CHANNEL

• shows which remote sensor’s data you are

viewing.

• is permanently displayed in the indoor temperature

area.

To auto-scan between sensors:

Press and hold CHANNEL for 2 seconds. Each sensor’s

data is displayed for 3 seconds.

To end auto-scan:

Press or .CHANNEL MEM

To toggle between current, minimum and maximum

records for the selected sensor:

Press repeatedly.MEM

To clear the records:

Press and hold for 2 seconds.MEM

TEMPERATURE TREND

Recent indoor / outdoor temperature trends are shown

by the trend icon.

RISING STEADY FALLING

ICE WARNING

If the channel 1 sensor falls between 3°C to -2°C (37°F

to 28°F), ﬂashes to warn you that the temperature is

approaching freezing.

NOTE The warning will automatically stop if the

temperature goes outside the ice-warning range.

HI / LO TEMPERATURE ALARM

An alarm can be set to sound if the sensor set to channel

1 records above or below a temperature of your choice.

To set alarm ON / OFF :

1. Press and hold

TEMP HI / LO .

2. Use and to select high / low temperature alarm.

Press to conﬁrm.TEMP HI / LO

3. Press or to set alarm ON / OFF and press

TEMP HI / LO to conﬁrm.

4. If alarm has been activated, use or to select

the temperature.

5. Press TEMP HI / LO

to conﬁrm.

To silence the hi / lo temperature alarm:

Press any key. The alarm resets automatically and will

resound if the hi / lo temperature selected is exceeded

again.

RESET

Press to return the unit to the default settings. RESET

PRECAUTIONS

This product is engineered to give you years of

satisfactory service if you handle it carefully. Here are a

few precautions:

• Do not immerse the unit in water. If you spill liquid over

it, dry it immediately with a soft, lint-free cloth.

• Do not clean the unit with abrasive or corrosive

materials.

• Do not subject the unit to excessive force, shock,

dust, temperature or humidity, which may result in

malfunction, shorter electronic life span, damaged

battery and distorted parts.

• Do not tamper with the unit’s internal components.

Doing so will invalidate the warranty on the unit and

may cause unnecessary damage. The unit contains

no user-serviceable parts.

• Only use fresh batteries as speciﬁed in the user’s

instructions. Do not mix new and old batteries.

• Do not use rechargeable batteries.

• Remove batteries when storing the product for a long

time.

• Due to printing limitations, the displays shown in this

manual may differ from the actual display.

• The contents of this manual may not be reproduced

without the permission of the manufacturer.

• Do not dispose this product as unsorted municipal

waste. Collection of such waste separately for

special treatment is necessary.

NOTE The technical speciﬁcations for this product and

the contents of the user manual are subject to change

without notice.

SPECIFICATIONS

TYPE DESCRIPTION

Main unit

Dimensions 93 x 52 x 118 mm

(L x W x D) (3.7 x 2.0 x 4.6 inches)

Weight 133 g (4.7 ounces) without

battery

Remote unit

Dimensions 96 x 50 x 22 mm

(L x W x D) (3.8 x 2.0 x 0.9 in)

Weight 62 g (2.22 ounces) without

battery

Temperature unit – °C / °F

Indoor range -5°C to 50°C (23°F to 122°F)

Outdoor range -30°C to 60°C

(-22°F to 140°F)

Resolution 0.1°C (0.2°F)

Remote unit

RF frequency 433MHz

Range Up to 30 meters (100 feet)

with no obstructions

Transmission Approx. every 40 seconds

Channel no. 1, 2 or 3

Clock

Synchronization Auto or disabled

Clock display HH:MM

Hour format 12hr AM/PM or 24hr

Calendar DD/MM or MM/DD

Weekday in 5 (E, G, F, I, S)

languages

Alarm 2-minute alarm

Power

Main unit 2 x UM-4 (AAA) 1.5V

batteries

Remote unit 1 x UM-3 (AA) 1.5V

battery

NOTE We recommend that you use alkaline batteries

with this product for longer usage and lithium batteries in

temperatures below freezing.

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientiﬁc.com) to learn more

about Oregon Scientiﬁc products such as digital cameras;

MP3 players; children’s electronic learning products and

games; projection clocks; health and ﬁtness gear; weather

stations; and digital and conference phones. The website

also includes contact information for our Customer Care

department in case you need to reach us, as well as

frequently asked questions and customer downloads.

We hope you will ﬁnd all the information you need on our

website, however if you’re in the US and would like to

contact the Oregon Scientiﬁc Customer Care department

directly, please visit:

www2.oregonscientiﬁc.com/service/default.asp

Call 1-800-853-8883.

For international inquiries, please visit:

www2.oregonscientiﬁc.com/about/international.asp

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This

device must accept any interference received, including

interference that may cause undesired operation.

WARNING Changes or modiﬁcations not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE This equipment has been tested and found

to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an ou tlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio / TV

technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact

for support or sales. Please call our customer service

number (listed on our website at www.oregonscientiﬁc.

com), or on the warranty card for this product) for all

inquiries instead.

Name: Oregon Scientiﬁc, Inc.

Address: 19861 SW 95th Ave., Tualatin,

Oregon 97062 USA

Telephone No.: 1-800-853-8883

declare that the product

Product No.: RMR382A

Product Name: Wireless Indoor / Outdoor Thermometer

with Self-Setting Atomic Clock

Manufacturer: IDT Technology Limited

Address: Block C, 9/F, Kaiser Estate,

Phase 1,41 Man Yue St., Hung Hom,

Kowloon, Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: 1) This device

may not cause harmful interference. 2) This device must

accept any interference received, including interference

that may cause undesired operation.

086L004376-010

RMR382A 086L004376-010_R1.indd 2 4/3/06 10:32:10 AM

Product specificaties

Merk:	Oregon Scientific
Categorie:	Weerstation
Model:	RMR382
Kleur van het product:	Zwart
Gewicht:	133 g
Breedte:	52 mm
Diepte:	118 mm
Hoogte:	93 mm
Meeteenheid temperatuur:	F, °C
Accu/Batterij voltage:	1.5 V
Alarm functie:	Ja
Klok functie:	Ja
Ophangsysteem voor aan de muur:	Ja
Receiver afmetingen (B x D x H):	50 x 22 x 96 mm
Aantal batterijen (receiver):	2
Temperature measurement range (outside) (T-T):	-30 - 60 °C
Temperature measurement range (inside) (T-T):	-5 - 50 °C
Aantal sensoren ondersteund (max):	3