Oregon Scientific RMR203HGA Handleiding

Oregon Scientific Weerstation RMR203HGA

Lees hieronder de 📖 handleiding in het Nederlandse voor Oregon Scientific RMR203HGA (2 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Temperature and Humidity Station

with Atomic Time

Model: RMR203HGA

USER MANUAL

OVERVIEW

FRONT VIEW (FIG 1)

1. Remote sensor reception indicator

2. Clock signal reception indicator

3. : Change settings / display MODE

4. : Activate backlight for 5 seconds LIGHT

5. / : Increase / decrease settings; activate /

deactivate clock reception signal

6. Outdoor temperature and humidity

Wireless sensor included does not include humidity.

To receive outdoor humidity you need a wireless sensor with

the humidity function.

7. Indoor temperature and humidity

8. Time zone

9. Clock with weekday

10. : View current, maximum, minimum temperature / MEM

humidity

11. Ice alert LED indicator

BACK VIEW (FIG 2)

1. : Select temperature unit °C / °F

2. : Reset unit to default settings RESET

REMOTE SENSOR (FIG 3)

1. LED status indicator

2. Wall mount hole

3. Battery compartment

4. RESET hole

5. switch CHANNEL

GETTING STARTED

INSERT BATTERIES

1. Remove the battery compartment.

2. Insert the batteries, matching the polarities (see FIG 2).

LOCATION MEANING

Clock / alarm Main unit batteries low

Outdoor temperature Sensor batteries low

and humidity area

REMOTE SENSOR

The main unit can collect data from up to 3 sensors.

To set up the sensor:

1. Open the battery compartment (see FIG 3).

2. Select a channel then press . RESET

3. Close the battery door.

4. Place the sensor within 30 m (98 ft) of the main unit

using the table stand or wall mount.

Ideal placements for the sensor would be in any TIP

location on the exterior of the home at a height of not more

than 5 ft and which can shield it from direct sunlight or wet

conditions for an accurate reading.

Use alkaline batteries for longer usage and consumer

grade lithium batteries in temperatures below freezing.

SENSOR DATA TRANSMISSION

To search for a sensor:

Press and hold + MODE simultaneously.

The sensor reception icon in the remote sensor area shows

the status:

ICON DESCRIPTION

Main unit is searching for sensor(s).

A channel has been found.

The sensor cannot be found.

TIP The transmission range may vary depending on many

factors. You may need to experiment with various locations

to get the best results.

CLOCK

CLOCK RECEPTION

This product is designed to synchronize its clock automatically

with WWVB-60 signal, within 3200km (2000 miles) of Fort

Collins Colorado.

To enable / disable signal reception:

Press and hold to enable or to disable signal

reception.

Reception takes 2-10 minutes. If the signal is weak,

it can take up to 24 hours to get a valid signal. If signal

reception is unsuccessful, place your unit next to a window,

press and hold to force another signal search.

Clock signal reception indicator:

STRONG SIGNAL WEAK SIGNAL NO SIGNAL

MANUALLY SET CLOCK

To set the clock manually, disable the signal reception ﬁrst.

1. Press and hold .MODE

2. Press or to change the settings.

3. Press to conﬁrm.MODE

4. The settings order is: time zone, 12/24 hr format, hour,

minute, year, calendar mode (day – month / month –

day), month, day and language.

Select the time zone: (P) Paciﬁc, (E) Eastern, (C) Central or

(M) Mountain.

The language options are English (E), German (D),

French (F), Italian (I), and Spanish (S).

To select display mode:

Press to choose between clock with seconds / MODE

weekday / calendar.

TEMPERATURE AND HUMIDITY

To toggle temperature unit:

Press .°C / °F

To auto-scan between sensors:

Press and hold + MEM to display each sensor’s data

for 3 seconds.

To end press .

To toggle between current, minimum and maximum

records for the selected sensor:

Press repeatedly.MEM

To clear the records:

Press and hold .MEM

ICE WARNING

If the channel 1 sensor falls between 3°C to

-2 °C (37°F to 28°F), LED indicator will ﬂash, and will stop

ﬂashing once the temperature is out of this range.

BACKLIGHT

Press to activate backlight for 5 seconds.LIGHT

RESET

Press to return to the default settings.RESET

PRECAUTIONS

• Do not subject the unit to excessive force, shock, dust,

temperature or humidity.

• Do not cover the ventilation holes with any items such as

newspapers, curtains etc.

• Do not immerse the unit in water. If you spill liquid over

it, dry it immediately with a soft, lint-free cloth.

• Do not clean the unit with abrasive or corrosive

materials.

• Do not tamper with the unit’s internal components. This

invalidates the warranty.

• Only use fresh batteries. Do not mix new and old

batteries.

• Images shown in this manual may differ from the actual

display.

RMR203HGA_M_EN_R2.indd 1 2007.6.21 9:49:08 AM

P/N:086L004999-013 REV1

1/2

www.OregonScientificStore.com

• When disposing of this product, ensure it is collected

separately for special treatment.

• Placement of this product on certain types of wood

may result in damage to its ﬁnish for which Oregon

Scientiﬁc will not be responsible. Consult the furniture

manufacturer's care instructions for information.

• The contents of this manual may not be reproduced

without the permission of the manufacturer.

• Do not dispose old batteries as unsorted municipal

waste. Collection of such waste separately for special

treatment is necessary.

• Please note that some units are equipped with a

battery safety strip. Remove the strip from the battery

compartment before ﬁrst use.

The technical speciﬁcations for this product and the

contents of the user manual are subject to change without

notice.

SPECIFICATIONS

TYPE DESCRIPTION

MAIN UNIT

L x W x H 73 x 47 x 132.5 mm

(2.87 x 1.85 x 5.22 in)

Weight 241 g (8.5 oz) without battery

Temperature range -5°C to 50°C (23°F to 122°F)

Resolution 0.1°C (0.2°F)

Signal frequency 433 MHz

Humidity range 25% - 95%

Humidity resolution 1%

Power 2 x UM-3 (AA) 1.5 V batteries

REMOTE UNIT (THN132N)

L x W x H 96 x 50 x 22 mm

(3.78 x 1.97 x 0.87 in)

Weight 62 g (2.22 ounces)

Transmission range 30 m (98 ft) unobstructed

Temperature range -20°C to 60°C (-4°F to 140°F)

Power 1 x UM-3 (AA) 1.5 V batteries

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientiﬁc.com) to learn more

about Oregon Scientiﬁc products. If you’re in the US and

would like to contact our Customer Care department directly,

please visit: www2.oregonscientiﬁc.com/service/support

Call 1-800-853-8883.

For international inquiries, please visit: www2.oregonscientiﬁc.

com/about/international

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This

device must accept any interference received, including

interference that may cause undesired operation.

WARNING Changes or modiﬁcations not expressly

approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

NOTE This equipment has been tested and found to

comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV

technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact for

support or sales. Please call our customer service number

(listed on our website at www.oregonscientiﬁc.com, or on the

warranty card for this product) for all inquiries instead.

Name: Oregon Scientiﬁc, Inc.

Address: 19861 SW 95th Ave.,Tualatin,

Oregon 97062 USA

Telephone No.: 1-800-853-8883

declare that the product

Product No.: RMR203HGA

Product Name: Temperature and Humidity

Station with Atomic Time

Manufacturer: IDT Technology Limited

Address: Block C, 9/F, Kaiser Estate,

Phase 1,41 Man Yue St.,

Hung Hom, Kowloon,

Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: 1) This device may

not cause harmful interference. 2) This device must accept

any interference received, including interference that may

cause undesired operation.

P/N: 086L004999-013

RMR203HGA_M_EN_R2.indd 2 2007.6.21 9:49:09 AM

P/N:086L004999-013 REV1

2 2/

Product specificaties

Merk:	Oregon Scientific
Categorie:	Weerstation
Model:	RMR203HGA
Kleur van het product:	Wit
Ingebouwd display:	Ja
Gewicht:	62 g
Breedte:	96 mm
Diepte:	22 mm
Hoogte:	50 mm
Accu/Batterij voltage:	1.5 V
Alarm functie:	Ja
Klok functie:	Ja
Meetfuncties:	Binnenthermometer
Meetfuncties trend display:	Thermometer
weerstation extremum data:	Thermometer
Type batterij:	AA
Vochtigheid meetbereik (buiten) (H-H):	25 - 95 procent
Temperature measurement range (inside) (T-T):	-20 - 60 °C