Oregon Scientific BAR688HGA Handleiding

Oregon Scientific Weerstation BAR688HGA

Lees hieronder de 📖 handleiding in het Nederlandse voor Oregon Scientific BAR688HGA (4 pagina's) in de categorie Weerstation. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Wireless Weather Station with

Temperature / Humidity Display and

Self - Setting Atomic Clock

MODEL: BAR688HGA

INTRODUCTION

Thank you for selecting this Oregon Scientic

TM Wireless

Weather Station with Temperature / Humidity Display and

Self - Setting Atomic Clock (BAR688HGA). This clock

is supplied with a remote sensor (THGR122N) and can

support up to 3 sensors in total (additional sensors sold

separately).

NOTE Please keep this manual handy as you use your new

product. It contains practical step-by-step instructions, as

well as technical specications and warnings you should

know about.

CLOCK OVERVIEW

FRONT VIEW

1. SNOOZE

2. Weather Forecast Area

3. Outdoor Temperature Area

4. Indoor Temperature Area

5. Clock / Alarm Area

BACK VIEW

1. : Change settings or TEMP / HUMIDITY HI / LO

enable / disable hi or lo temperature / humidity alarm

for channel 1

2. / : Increase / decrease setting; activate / deactivate

clock reception signal

LCD DISPLAY

Weather Forecast Area:















Outdoor Temperature Area:

1. Heat index icon

2. Hi / lo temperature alarm

3. Sensor reception icon

4. Sensor battery low

5. Max / min icon

6. Temperature display

7. Ice warning is active

8. Hi / lo humidity alarm

9. Temperature trend

10. Humidity trend

11. Humidity display























Indoor Temperature Area:

1. Internal sensor icon

2. Max / min icon

3. Temperature display

4. Temperature trend

5. Humidity trend

6. Humidity display













Clock / Alarm Area:

1. Alarm set

2. AM / PM icon

3. Clock signal reception

4. Low battery icon

5. Clock

6. Alarm mode icon

7. Moon phase

















REMOTE SENSOR (THGR122N)

1. LED status indicator:

Blinks red during data

transmission

2. LCD screen

1. Wall mount hole

2. hole RESET

3. switchCHANNEL

4. Battery compartment

GETTING STARTED

SETTING UP THE CLOCK

Insert batteries before rst use, matching the polarity (+

and -). after each battery change.RESET

SENSOR DATA TRANSMISSION

indicates main unit batteries are low.

NOT E Do not use recharge abl e batteries. We

recommend that you use alkaline batteries with this product

for longer usage and lithium batteries in temperatures

below freezing.

REMOTE SENSOR

The sensor collects temperature readings approx. every

40 seconds and sends them to the main unit. The main

unit can collect data from up to 3 sensors.

To set up the sensor:

1. Remove the screws from the battery door.

2. Insert the batteries, matching the polarity ( ).+ / -

3. Select a channel. Make sure you use a different channel

for each sensor.

4. Place the sensor near the main unit. Press on RESET

the sensor.

5. Simultaneously press CHANNEL and MEM on the main

unit to initiate signal sending between the sensor and

main unit.

6. Close the battery door and secure the screws

7. Place the sensor in the desired location using the table

stand or wall mount.

For best results:

• Place the sensor out of direct sunlight and moisture.

• Do not place the sensor more than 30 m (100 ft) from

the main (indoor) unit.

• Position the sensor so that it faces the main (indoor)

unit, minimizing obstructions such as doors, walls, and

furniture.

• Place the sensor in a location with a clear view to the

sky, away from metallic or electronic objects.

• Position the sensor close to the main unit during cold

winter months as below-freezing temperatures may

affect battery performance and signal transmission.

Data is sent from the sensor(s) every 40 seconds. The

sensor reception icon in the remote sensor area shows

the status.

ICON DESCRIPTION

and “- - . -“

(Outdoor

temperature area)

The sensor cannot be found.

Search for the sensor or check

batteries

To search for a sensor:

Simultaneously, press and hold and for MEM CHANNEL

2 seconds.

NOTE If the sensor is still not found, check the batteries,

obstructions, and remote unit location.

CLOCK

CLOCK RECEPTION

This product is designed to synchronize its date and time

automatically once it is within range of the WWVB-60 signal

from the atomic clock in Boulder, Colorado.

The sensor collects the radio signals whenever it is within

1500 km (932 miles) of a signal.

NOTE Initial reception takes 2-10 minutes for rst set up

or when RESET is pressed. Once complete, the reception

icon will stop blinking. If the signal is weak, it can take up

to 24 hours to get a valid signal.

RECEPTION SIGNAL

To enable and force a signal search:

Press and hold for 2 seconds.

To disable the signal reception:

Press and hold for 2 seconds.

ashes when it is disabled.

STRONG SIGNAL WEAK SIGNAL NO SIGNAL

SET CLOCK

To manually set the clock make sure the clock signal

reception is disabled.

1. Press and hold for 2 seconds.MODE

2. Select the US time zone (Pacic (P), Eastern (E),

Central (C) and Mountain (M)), hour, minute, year,

month, day and language. Press or to change the

setting.

3. Press to conrm.MODE

NOTE The language options are English (E), German (D),

French (F), Italian (I), and Spanish (S).

Press to choose between the clock with seconds MODE

and clock with weekday display modes.

1. Pressure trend

2. Weather forecast

3. Comfort zone

4. Pressure icon

5. Altitude icon

6. Pressure / Altitude unit

7. UV index icon

USER MANUAL

3. : Switch remote sensor displayCHANNEL

4. HEAT INDEX: Display heat index

5. : Change settings / displayMODE

6. : View alarm status; set alarmALARM

7. Battery compartment

8. : Vie w cu rrent , maximum a nd minimum MEM

temperature / humidity

9. : Select pressure unit; set altitudePRESSURE

10. °C / °F: Select temperature unit

11. RESET: Reset unit to default settings

The transmission range may vary depending on many

factors. You may need to experiment with various locations

to get the best results.

Standard Alkaline batteries contain signicant amounts of

water. Because of this they will freeze in low temperatures

of approximately -12°C (10°F). Disposable Lithium

batteries have a much lower threshold for temperature

with an estimated freezing range of below -30°C (-22°F).

Wireless ranges can be impacted by a variety of factors

such as extremely cold temperatures. Extreme cold may

temporarily reduce the effective range between the sensor

and the base station. If the unit's performance fails due to

low temperature, the unit will resume proper functioning

as the temperature rises to within the normal temperature

range (i.e. no permanent damage will occur to the unit due

to low temperatures).

Sensor 1 is sending data

A channel has been found

Main unit is searching

for the sensor(s)

Clock signal reception indicator:

086L004255-016

SPECIFICATIONS

MAIN UNIT

TYPE DESCRIPTION

241 g (8.5 oz) without battery

117 x 80 x 171 mm

(4.78 x 3.27 x 6.98 in)

°C / °F

0.1°C (0.2°F)

-5°C to 50°C (23°F to 122°F)

WWVB-60 (US)

Weight

L x W x H

Temperature unit

Resolution

Temperature range

Clock frequency

Synchronization

Signal frequency

Clock

Humidity range

Humidity resolution

MEM

Alarm duration

Snooze

Clock display

Hour format

Calendar

Power

L x W x H

Weight

Transmission range

Auto or disabled

433 MHz

Auto or manual (disabled)

25% - 95%

Min / Max relative humidity and

temperature

2 minutes

8 minutes

HH:MM:SS

HH:MM: Day of Week

12 / 24 hour format

MM / DD or DD / MM

language selectable:

E, D, F, I and S

3 x UM-3 (AA) 1.5 V batteries

92 x 60 x 20 mm

(3.6 x 2.4 x 0.8 in)

62 g (2.22 ounces)

30 m (100 ft) unobstructed

REMOTE UNIT

Temperature Range

Power

-30°C to 60°C

(-22°F to 140°F)

2 x UM-4 (AAA) 1.5 V batteries

NOTE We recommend that you use alkaline batteries

with this product for longer usage and lithium batteries in

temperatures below freezing.

ABOUT OREGON SCIENTIFIC

Visit our website (www.oregonscientic.com) to learn more

about Oregon Scientic products such as digital cameras;

MP3 players; children’s electronic learning products and

games; projection clocks; health and tness gear; weather

stations; and digital and conference phones. The website

also includes contact information for our Customer Care

department in case you need to reach us, as well as fre-

quently asked questions and customer downloads.

We hope you will nd all the information you need on our

website, however if you’re in the US and would like to

contact the Oregon Scientic Customer Care department

directly, please visit:

www2.oregonscientic.com/service/default.asp

Call 1-800-853-8883.

For international inquiries, please visit:

www2.oregonscientic.com/about/international.asp

FCC STATEMENT

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) This

device must accept any interference received, including

interference that may cause undesired operation.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

WARNING Changes or modifications not expressly

approved by the party responsible for compliance could

void the user's authority to operate the equipment.

NOTE This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and u sed in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio / TV

technician for help.

DECLARATION OF CONFORMITY

The following information is not to be used as contact for

support or sales. Please call our customer service number

(listed on our website at www.oregonscientic.com), or

on the warranty card for this product) for all inquiries

instead.

Name: Oregon Scientic, Inc.

Address: 19861 SW 95th Ave.,Tua latin,

Oregon 97062 USA

Telephone No.: 1-800-853-8883

declare that the product

Product No.: BAR688HGA

Product Name: Wireless Weather Station with

Temperature / Humidity Display

and Self - Setting Atomic Clock

Manufacturer: IDT Technology Limited

Address: Block C, 9/F, Kaiser Estate,

Phase 1,41 Man Yue St.,

Hung Hom, Kowloon,

Hong Kong

is in conformity with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: 1) This device

may not cause harmful interference. 2) This device must

accept any interference received, including interference

that may cause undesired operation.

SET ALTITUDE

To ensure barometric readings are reliable set the altitude

to reect distance from sea level at your position.

1. Press and hold for 2 seconds.PRESSURE

2. Use and to set the altitude in 10 m (33 ft) increments

from 100 m (328 ft) to 2500 m (8202 ft).

3. Press to conrm.PRESSURE

WEATHER FORECAST

This product forecasts the next 12 to 24 hours of weather

within a 30-50 km (19-31 mile) radius based on barometric

pressure trend readings.

ICON DESCRIPTION

TEMPERATURE AND HUMIDITY

To toggle temperature unit:

Slide °C / °F to the desired setting. The setting for the main

unit overrides the remote sensor setting.

MAXIMUM / MINIMUM RECORDS

To view records:

1. Press to select a sensor.CHANNEL

2. Press to toggle maximum / minimum and current MEM

settings for the sensor selected.

To clear maximum and minimum records press and hold

MEM for 2 seconds.

ICE WARNING

If the channel 1 sensor falls between 3°C to –2°C (37°F

to 28°F), ashes to warn you that the temperature is

approaching freezing.

NOTE The warning will automatically stop if the temperature

goes outside the ice-warning range.

TEMPERATURE, HUMIDITY AND PRESSURE TREND

The temperature, humidity and pressure trend icons are

based on recent sensor readings.

RISING STEADY FALLING

To set alarm ON / OFF:

1. Press and hold TEMP / HUMIDITY HI / LO .

2. Use and to select high / low temperature / humidity

alarm. Press TEMP / HUMIDITY HI / LO to conrm.

3. Press / to set alarm ON / OFF and press TEMP /

HUMIDITY HI / LO to conrm.

4. If alarm has been activated, use and to select the

temperature / humidity.

5. Press to conrm.TEMP / HUMIDITY HI / LO

To silence the hi / lo alarm:

Press any key. The alarm resets automatically and will

resound if the hi / lo temperature selected is recorded

again.

HEAT INDEX

The heat index combines temperature and humidity data

to describe the actual temperature felt.

Clear

Cloudy

Rainy

Partially Cloudy

WARNING HEAT INDEX MEANING

Extreme

danger

Strong risk of

dehydration / sun

stroke

54.5°C / (130°F)

or above

Danger Heat exhaustion

likely

40.5 - 54°C

(105 - 129°F)

Extreme

caution

Possibility of heat

dehydration

32.2 - 40°C

(90 - 104°F)

Caution Possibility of heat

exhaustion

26.6 - 31.7°C

(80 - 89°F)

• To display the heat index, press HEAT INDEX.

• To toggle between current / maximum / minimum

readings, press HEAT INDEX CHANNEL, then press

to select channel 1-3 or indoor, followed by .MEM

• To toggle between temperature / humidity and heat index

display, press and hold HEAT INDEX for 2 seconds.

Press HEAT INDEX again to stop this feature.

NOTE If the heat index is below 80°F / 26°C, or the desired

channel is not working, the heat index will display NA .

COMFORT ZONE

The comfort zone assesses the climate based on current

temperature and humidity measurements.

ICON TEMPERATURE HUMIDITY

> 70%Any

40 - 70%

20 - 25°C

(68 - 77°F)

< 40%Any

MOON PHASE

• When calendar is set press or to view the moon

phase for the next / previous day.

• Press and hold or to scan through the years (2001

to 2099).

Waxing Crescent

New Moon

Waxing Gibbous

First quarter

Full Moon

Last quarter

Waning Gibbous

Waning Crescent

RESET

Press to return the unit to the default settings.RESET

PRECAUTIONS

This prod uct is engineered to give you years of

satisfactory service if you handle it carefully. Here are a

few precautions:

• Do not subject the unit to excessive force, shock,

dust, temperature or humidity, which may result in

malfunction, shorter electronic life span, damaged

battery and distorted parts.

• Do not immerse the unit in water. If you spill liquid over

it, dry it immediately with a soft, lint-free cloth.

• Do not clean the unit with abra sive or corr osive

materials.

• Do not tamper with the unit’s internal components.

Doing so will invalidate the warranty on the unit and

may cause unnecessary damage. The unit contains no

user-serviceable parts.

ALARM

To set the alarm:

1. Press and hold for 2 seconds.ALARM

2. Press / to set hour / minute.

3. Press or to conrm. indicates alarm ALARM MODE

is ON.

To toggle alarms ON / OFF:

1. Press to display alarm timeALARM

2. Press again to turn alarm ON / OFF.ALARM

To silence the alarm:

• Press to silence it for 8 minutesSNOOZE

• Press any key except to turn the alarm off SNOOZE

and activate it again after 24 hours.

BAROMETER

Barometer readings from the past 24 hours are stored by

the main unit and used to provide weather forecast.

To select barometer measurement unit:

Press to toggle between mb and inHg.PRESSURE

HI / LO TEMPERATURE /HUMIDITY ALARMS

Temperature and humidity alerts can be set to sound

if sensor set to channel 1 records above or below a

temperature/humidity of your choice.

• Only use fresh batteries as specied in the user’s

instructions. Do not mix new and old batteries.

• Due to printing limitations, the displays shown in this

manual may differ from the actual display.

• The contents of this manual may not be reproduced

without the permission of the manufacturer.

NOTE The technical specications for this product and

the contents of the user manual are subject to change

without notice.

Product specificaties

Merk:	Oregon Scientific
Categorie:	Weerstation
Model:	BAR688HGA

Heb je hulp nodig?

Als je hulp nodig hebt met Oregon Scientific BAR688HGA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Weerstation Oregon Scientific

Oregon Scientific Alizé BAR268HGA Handleiding

14 December 2024

Oregon Scientific RAA 501 H Handleiding

14 November 2024

Oregon Scientific WMR 300 Handleiding

14 November 2024

Oregon Scientific THC138 Handleiding

14 November 2024

Oregon Scientific RMR203HG Handleiding

14 November 2024

Oregon Scientific WMR180 Handleiding

14 November 2024

Oregon Scientific BAR206X Handleiding

9 April 2024

Oregon Scientific BAR 888A Handleiding

5 April 2024

Oregon Scientific AP 928 - WMR928NX Handleiding

16 Oktober 2023

Oregon Scientific BA200A Handleiding

16 Oktober 2023

Handleiding Weerstation

Nieuwste handleidingen voor Weerstation

Steinberg SBS-RS-40 Handleiding

15 December 2024

Steinberg SBS-WS-600 Handleiding

15 December 2024

TFA Life 35.1153.02 Handleiding

14 December 2024

TFA Connect 35.1143.01 Handleiding

14 December 2024

TFA 35.1133.01 Handleiding

14 December 2024

TFA 35.1089 Handleiding

14 December 2024

TFA 35.1078.10 Handleiding

14 December 2024

TFA Weather Boy 35.1159.02 Handleiding

14 December 2024

TFA 30.3034.01 Handleiding

14 December 2024

EMOS E0531 Handleiding

13 December 2024