Onkyo SKS-4600 Handleiding

Onkyo Speaker SKS-4600

Lees hieronder de 📖 handleiding in het Nederlandse voor Onkyo SKS-4600 (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
En
Thank you for your purchase of the Onkyo speaker
system.
Please read this manual thoroughly before using it.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new speaker system.
Please retain this manual for future reference.
SKF-4600
SKS-4600
Speaker System
Instruction Manual
Before using this unit
• The speaker cabinet is made of wood and is therefore
sensitive to extreme temperatures and humidity.
Avoid placing the speaker systems in locations
subjected to direct sunlight, or in smoky or in humid
places, such as near an air conditioner, humidifier,
bathroom, or kitchen. Doing so may result in damage
to the speaker.
• Place the unit on a rigid, level surface. Placing it on a
slanted surface or weak base not only may cause the
unit to fall, but also results in decreased sound
quality.
• Be sure to turn off your amplifier before connecting
the speaker system. Connecting them with the
amplifier's power on may result in damage to the
amplifier or the speaker system.
• Keep water or other liquids away from the unit. If
water is spilled into the unit, not only the unit but also
the speakers themselves may be damaged.
Precaution on use
• This speaker system can handle the specified input
power when it is used for ordinary music
reproduction. If the following abnormal signals are fed
to the speaker, however, an overcurrent may flow in
the internal circuits, causing burning or breakage of
the wires even if the input power is below the
specified rating.
1. Noise produced when FM station is not tuned in
2. Sound produced when fast-forwarding cassette
tape deck
3. High-frequency sound generated by an oscillator,
an electronic musical instruments, etc.
4. Oscillating amplifier signals
5. Special test signals produced by audio checking
CD, etc.
6. Sound produced when connecting or
disconnecting audio connection cables (Always
turn off the amplifier’s power before connecting or
disconnecting cables.)
7. Howling when a microphone is used
• Do not place magnetic objects such as screwdrivers
and iron parts near the tweeter since they use
speakers with strong magnets. Otherwise, the
objects may be attracted, causing injury or damaging
the diaphragm.
En-2
Model name
SKF-4600
Front speaker system 2×
SKS-4600
Center speaker system SKC-4600 × 1
Surround speaker system SKM-4600 × 2
Connection
• Turn the sound volume to the minimum and disconnect the
power cord from the amplifier before connecting the
speaker cables.
• The nominal impedance of this speaker system is 6 . UseΩ
only amplifiers capable of handling this impedance.
• Use the supplied speaker cables to connect between
speaker’s input terminals and the amplifier’s speaker
terminals as illustrated below.
• Connect the speaker cables securely to the terminals, with
the core wires twisted properly. In this case, make sure that
the core wires do not touch each other. Note that a short
circuit in core wires may result in damage to the amplifier.
Connecting to AV amplifier
SKF-4600
SKC-4600 / SKM-4600
Before turning on the amplifier’s power switch:
• Make sure that the positive (+) and negative (-) speaker
cables do not contact each other. Otherwise, a short-circuit
may occur, causing damage to the amplifier.
• Be sure to connect the speaker cables with correct polarity
(connect the speaker’s positive (+) and negative (-) binding
posts with the amplifier’s corresponding speaker
terminals). Reversed polarity results in impaired bass-
range reproduction, causing mislocalization of the sound
image. Also, be sure to connect the Right and Left
speakers with the amplifier’s corresponding speaker
terminals.
• Pull lightly on the speaker cables to ensure that they are
connected firmly.
L
27122965
REMOTE
CON TROL
CAUT ION: SP EAKER IMPEDANCE
6 OHMS MIN . /SPEAKER
ANT ENNA
FM
75
AM
COAXIALOPTI CAL
12
IN IN IN IN FRONT SURR CENTER
SUB
WOOFER
VID EO 2 VIDEO 1
OUT
DIG ITAL INP UT
DVD
MONIT OR
OUT
DVD
TAP ECD
SUBWOOFER
PRE OUT
L
R
R
VID EO 3
VID EO 2VID EO 3 VID EO 1
VID EO
OPTI CAL
ININ IN I N
DIG IT AL
OUT PUT
IN
IN PUT 1IN PUT 2 OUTPUT
COMPONENT VID EO
P
R
P
B
Y
OUT
OUT
DIG IT AL
INPUT
L
R
S VID EO
FRONT
SPEAKERS
SURROUND
SPEAKERS
CENT ER
SPEAKER
R
L
R
L
A B
SURROUND BACK
SPEAKER
R
L
AC OUT LET S
SWITCHED
TOTAL 100W MAX.
AC 230-240
V
50
Hz
SURROUND BACK
SPEAKER
+–+–
+–
+–+–
FRONT
SPEAKERS
SURROUND
SPEAKERS
CENTER
SPEAKER
R
L
R
L
A B
R
L
SKF-4600
Front right
speaker
SKC-4600
Center speaker
SKM-4600
Surround right
speaker
SKF-4600
Front left
speaker
SKM-4600
Surround left speaker
Red
Green
Blue
Gray
AV Amplifier
White
1. Strip the insulation of speaker cables,
and twist the core wires tightly.
2. While pressing the lever, insert the wire
into the hole, and then release the lever.
3. Make sure that the terminals are gripping
the core wires, not the insulation.
15 mm
1. Strip the
insulation of
speaker
cables, and
twist the core
wires tightly.
2. Loosen the
terminal screw, and
insert the wire into
the hole (until the
core wires are
inserted fully).
3. Fasten the
terminal
screw.
En-3
Attaching the speaker stands (for SKF-4600 only)
Attach the supplied speaker stand at the bottom of each speaker
cabinet using the supplied screws as shown in the figure below.
For better sound quality, you are recommended to attach the supplied
cork spacer on the speaker stand.
In addition to the sound quality improvement, attaching the cork
spacers also provide non-sliding and stabilizing effects for the speaker
cabinet.
Attaching and detaching the speaker grilles
This speaker system uses detachable grilles. Use the following
method to attach or detach the grilles.
1. While holding the bottom edge of the speaker grille with your both
hands, pull it gently toward you to remove the bottom of the grille.
2. In the same way, gently pull the upper edge of the speaker grille
toward you to remove it from the main unit.
3. To replace the grill, push the projections at the corners into the
grille plug holes on the speaker cabinet.
Use with a TV set
In general, Braun tubes used for color television sets, etc. are
extremely sensitive and can be affected even by the magnetism of the
earth. If a speaker system is used near them, therefore, discoloration
or distortion of pictures will occur. To allow use with color television
sets, etc., this speaker system is provided with magnetic shielding.
Even so, discoloration may still result, depending on the installation
environment. If discoloration occurs, turn off the power of the television
set, wait for 15 to 30 minutes and then turn it on again. This activates
the self-demagnetizing function of the television set, improving the
display condition. If discoloration persists even after performing this
remedy, move the speaker apart from the television set. Discoloration
may also be caused when a magnet or other magnetizing object exists
near the television because of the combined effect.
Speaker care
Your Onkyo speakers are finished with a very high quality polymer
laminate covering that serves to protect the wood speaker cabinet.
Wipe the cabinet periodically with a dry, silicon-embedded or plain soft
cloth.
The covering may be cleaned with a soft cloth moistened with water
and a mild soap. Avoid the use of furniture polishes or harsh
cleansers. Use a soft brush or hand vacuum cleaner to remove dust
and lint from the grille material.
Placement
SKF-4600 Front speaker system
The sound quality a speaker system reproduces varies greatly
depending on the construction and area of the room where it is
installed, as well as the location and size of the furniture. For better-
quality sound, observe the following precautions.
•Avoid placing the speaker system on an elevated object such as
on concrete blocks. Instead, place it on a rigid floor surface with
minimal vibration. Also note that high-quality bass cannot be
obtained if the speaker system is unstably positioned. Generally
speaking, placing the speaker system on several small-diameter
supports results in better bass than placing it directly on the
installation surface. Moreover, if you feel the bass reproduced by
the system is too weak, move the speaker system closer to the
wall behind it. You can thus control the strength of the reproduced
bass by the position of the speakers.
•In many rooms, the furniture and wall affect the reproduced sound
quality. For stereo sound reproduction, placing the Right and Left
speakers in the same condition produces the best results. If they
are placed in extremely different conditions, the Right- and Left-
channel balance will be adversely affected.
•The ideal placement of the speaker system is as follows: Imagine
an equilateral triangle and position the Right and Left speakers on
both ends of the base. The ideal listening position is at or slightly
to the rear of the triangle apex.
•Glazed doors or surrounding walls in front of the speaker system may
cause the resonance of specific frequency ranges due to reflected
sound. To eliminate this resonance, place some sound-absorbing
material such as a thick curtain in front of the doors or walls.
SKC-4600 Center speaker and SKM-4600 Surround
speaker system
For better-quality sound, observe the following precautions when you
install the speaker system:
•Placing the speaker system on several small-diameter supports
generally results in better sound than placing it directly on a wide
installation surface. Also note that high quality bass cannot be
obtained if the speaker system is unstably positioned. Always use
the cork spacers or thin metal discs (such as coins) to seat the
speaker stably.
•Place the Right and Left surround speakers in similar conditions. If
they are placed in extremely different conditions, left right channel
balance will be adversely affected.
SKC-4600 Center Speaker
Place the SKC-4600 as close as possible to your television set, for
example, above or below the television set. Be sure to set the SKC-
4600 firmly on the television set or other equipment so that it cannot
slip and fall. This is especially important if you have small children. If
the SKC-4600 is to be placed on a television set, be sure that:
•The supporting area of the TV is larger than that of the SKC-4600.
•The TV's support surface is flat and level.
•The TV is not placed on an unstable support.
SKM-4600 Surround Speaker
If the speakers are to be wall-mounted, make sure that the walls are
strong enough to support the speaker's weight. The weight that
mounting screws can support varies greatly depending on the wall
material and the position of the reinforcing ribs embedded in the wall.
Use the thickest and longest possible mounting screws with mounting
screw head diameters less than 10 mm and shank diameters less than
4 mm (consult with your interior designer or contractor).
SKF-4600
Removal Replacement
Screw M6 × 20 mm
Speaker stand
Speaker cabinet
Cork spacer


Product specificaties

Merk: Onkyo
Categorie: Speaker
Model: SKS-4600

Heb je hulp nodig?

Als je hulp nodig hebt met Onkyo SKS-4600 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Onkyo

Handleiding Speaker

Nieuwste handleidingen voor Speaker

Braun

Braun LE03 Handleiding

23 November 2024
HK Audio

HK Audio L5-112X Handleiding

23 November 2024
Sony

Sony SS-SPG01 Handleiding

22 November 2024
Sony

Sony SS-MB200H Handleiding

22 November 2024
Sony

Sony SS-MB300H Handleiding

22 November 2024
JBL

JBL Studio 690 Handleiding

22 November 2024
JBL

JBL Studio 680 Handleiding

22 November 2024